Instantaneous Properties of Multi-Degrees-of-Freedom Motions—Point Trajectories

1987 ◽  
Vol 109 (1) ◽  
pp. 107-115 ◽  
Author(s):  
Ashitava Ghosal ◽  
Bernard Roth
Keyword(s):  
General Framework ◽  
Degrees Of Freedom ◽  
Rigid Bodies ◽  
Global Motion ◽  
Analysis Techniques ◽  
Trajectory Point ◽  
Prismatic Joints ◽  
Point Trajectories ◽  
Three Degrees Of Freedom

A general framework is presented for the study of the properties of trajectories generated by points embedded in rigid bodies undergoing multi-degrees-of-freedom motions. Quantities are developed to characterize point trajectories generated by different mechanisms and to distinguish between different positions along the same trajectory. Point trajectories are classified into three types according to whether the number of degrees of freedom is less than, equal to, or greater than the dimension of the space in which the motion takes place. Local and global motion properties are developed for each of these three cases. A new way of using the redundant degrees of freedom in (redundant) mechanisms is presented. These analysis techniques are applied to two- and three-degrees-of-freedom mechanisms containing rotary and prismatic joints.

scholarly journals A Translational Three-Degrees-of-Freedom Parallel Mechanism With Partial Motion Decoupling and Analytic Direct Kinematics

2020 ◽  
Vol 12 (2) ◽  
Author(s):  
Huiping Shen ◽  
Damien Chablat ◽  
Boxiong Zeng ◽  
Ju Li ◽  
Guanglei Wu ◽  
...  
Keyword(s):  
Parallel Mechanism ◽  
Design Theory ◽  
Degrees Of Freedom ◽  
Analytic Solutions ◽  
Inverse Kinematic ◽  
Kinematic Modeling ◽  
Topological Design ◽  
Prismatic Joints ◽  
Topological Characteristics ◽  
Three Degrees Of Freedom

Abstract According to the topological design theory and the method of parallel mechanism (PM) based on position and orientation characteristic (POC) equations, this paper studied a three-degrees-of-freedom (3-DOF) translational PM that has three advantages, i.e., (i) it consists of three fixed actuated prismatic joints, (ii) the PM has analytic solutions to the direct and inverse kinematic problems, and (iii) the PM is of partial motion decoupling property. First, the main topological characteristics, such as the POC, degree-of-freedom, and coupling degree, were calculated for kinematic modeling. Thanks to these properties, the direct and inverse kinematic problems can be readily solved. Further, the conditions of the singular configurations of the PM were analyzed, which corresponds to its partial motion decoupling property.

The Qualitative Synthesis of Parallel Manipulators

2004 ◽  
Vol 126 (4) ◽  
pp. 617-624 ◽  
Author(s):  
Jorge Angeles
Keyword(s):  
Degrees Of Freedom ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Qualitative Reasoning ◽  
Rigid Bodies ◽  
Three Dimensions ◽  
Qualitative Synthesis ◽  
Motion Representation ◽  
Six Degrees Of Freedom ◽  
Three Degrees Of Freedom

As shown in this paper, when designing parallel manipulators for tasks involving less than six degrees of freedom, the topology can be laid out by resorting to qualitative reasoning. More specifically, the paper focuses on cases whereby the manipulation tasks pertain to displacements with the algebraic structure of a group. Besides the well-known planar and spherical displacements, this is the case of displacements involving: rotation about a given axis and translation in the direction of the same axis (cylindrical subgroup); translation in two and three dimensions (two- and three-dimensional translation subgroups); three independent translations and rotation about an axis of fixed direction, what is known as the Scho¨nflies subgroup; and similar to the Scho¨nflies subgroup, but with the rotation and the translation in the direction of the axis of rotation replaced by a screw displacement. For completeness, the fundamental concepts of motion representation and groups of displacements, as pertaining to rigid bodies, are first recalled. Finally, the concept of Π-joint, introduced elsewhere, is generalized to two and three degrees of freedom, thereby ending up with the Π2-and the Π3-joints, respectively.

Instantaneous Properties of Multi-Degrees-of-Freedom Motions—Line Trajectories

1987 ◽  
Vol 109 (1) ◽  
pp. 116-124 ◽  
Author(s):  
Ashitava Ghosal ◽  
Bernard Roth
Keyword(s):  
Rigid Body ◽  
General Framework ◽  
Degrees Of Freedom ◽  
Rigid Bodies ◽  
Two Degrees Of Freedom ◽  
Global Properties ◽  
New Concepts ◽  
Line Trajectory

A general framework is presented for the study of the properties of trajectories generated by lines embedded in rigid bodies undergoing multi-degrees-of-freedom motions. Several new concepts, such as a line’s angular and linear velocities and accelerations, are introduced and used to (1) characterize the differences between line trajectories generated by different mechanisms; (2) distinguish trajectories generated by different lines in the same rigid body; (3) distinguish properties at different positions in the same trajectory. Line trajectories are classified according to the number of degrees of freedom of the motion, and local and global properties are discussed. These techniques are illustrated in an example of a line trajectory generated by a two-degrees-of-freedom manipulator.

Mobility, Kinematic Analysis, and Dimensional Optimization of New Three-Degrees-of-Freedom Parallel Manipulator With Actuation Redundancy

2017 ◽  
Vol 9 (4) ◽  
Author(s):  
Lingmin Xu ◽  
Qinchuan Li ◽  
Ningbin Zhang ◽  
Qiaohong Chen
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Force Transmission ◽  
Transmission Index ◽  
Prismatic Joints ◽  
Redundantly Actuated ◽  
Force Transmissibility ◽  
Solution Velocity ◽  
Three Degrees Of Freedom

Parallel manipulators (PMs) with redundant actuation are attracting increasing research interest because they have demonstrated improved stiffness and fewer singularities. This paper proposes a new redundantly actuated parallel manipulator that has three degrees-of-freedom (DOFs) and four limbs. The proposed manipulator is a 2UPR-2PRU parallel manipulator (where P represents an actuated prismatic joint, R represents a revolute joint, and U represents a universal joint) that is actuated using four prismatic joints; two of these joints are mounted on the base to reduce the movable mass. Mobility analysis shows that the moving platform has two rotational DOFs and one translational DOF. First, the inverse displacement solution, velocity, and singularity analyses are discussed. Next, the local transmission index (LTI) and the good transmission workspace are used to evaluate the motion/force transmissibility of the 2UPR-2PRU parallel manipulator. Finally, the parameter-finiteness normalization method (PFNM) is used to produce an optimal design that considers the good transmission workspace. It is thus shown that the motion/force transmission of the proposed manipulator is improved by optimizing the link parameters.

Mobility and singularity analyses of a symmetric multi-loop mechanism for space applications

2021 ◽  
pp. 095440622199555
Author(s):  
Chuanyang Li ◽  
Jorge Angeles ◽  
Hongwei Guo ◽  
Huiyin Yan ◽  
Dewei Tang ◽  
...  
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Singularity Analysis ◽  
Space Applications ◽  
Aerospace Applications ◽  
Constraint Analysis ◽  
Multi Stage ◽  
Prismatic Joints ◽  
The Subject ◽  
Three Degrees Of Freedom

A symmetric, double-tripod multi-loop mechanism (DTMLM), for aerospace applications, is the subject of this paper. Its mobility and singularity are analyzed, while introducing a novel tool, the cell-division method for singularity analysis, applicable to multi-loop mechanisms. The key principle of this method lies in replacing the singularity analysis of the original multi-loop mechanism with: (1) that of an equivalent simpler parallel mechanism; (2) the constraint analysis between loops; and (3) the singularity analysis of simpler kinematic subchains. Then, the mechanism is transformed into a simpler, equivalent parallel mechanism with three identical kinematic subchains. Its mobility and singularity are analyzed based on screw algebra, which leads to a key conclusion about the geometric properties of this mechanism. Results show that: (a) the DTMLM has three degrees of freedom (dof), i.e., two rotational dof around two intersecting axes lying in the middle plane of the mechanism, and one translational dof along the normal to the said plane (2R1T); and (b) the singularities of the 3-RSR parallel mechanism are avoided in the DTMLM by means of prismatic joints, singularities in the DTMLM occurring on the boundary of its workspace. Thus, the DTMLM has a 2R1T mobility everywhere within its workspace. When a set of multi-loop mechanisms of this kind are stacked as modules to assemble a multi-stage manipulator for space applications, the modules can be designed so that, under paradigm operations, all individual loops operate within their workspace, safe from singularities.

scholarly journals Active Disturbance Rejection for a Three Degrees of Freedom Gyroscope

2018 ◽  
Vol 51 (13) ◽  
pp. 372-377 ◽  
Author(s):  
Juan E. Andrade García ◽  
Alejandra Ferreira de Loza ◽  
Luis T. Aguilar ◽  
Ramón I. Verdés
Keyword(s):  
Disturbance Rejection ◽  
Degrees Of Freedom ◽  
Active Disturbance Rejection ◽  
Three Degrees Of Freedom

scholarly journals Cyclic Deformation of Microcantilevers Using In-Situ Micromanipulation

2021 ◽  
Author(s):  
A. H. S. Iyer ◽  
M. H. Colliander
Keyword(s):  
Degrees Of Freedom ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Structural Components ◽  
Cyclic Testing ◽  
Phase Boundaries ◽  
Bulk Specimen ◽  
Arbitrary Position ◽  
Three Degrees Of Freedom

Abstract Background The trend in miniaturisation of structural components and continuous development of more advanced crystal plasticity models point towards the need for understanding cyclic properties of engineering materials at the microscale. Though the technology of focused ion beam milling enables the preparation of micron-sized samples for mechanical testing using nanoindenters, much of the focus has been on monotonic testing since the limited 1D motion of nanoindenters imposes restrictions on both sample preparation and cyclic testing. Objective/Methods In this work, we present an approach for cyclic microcantilever bending using a micromanipulator setup having three degrees of freedom, thereby offering more flexibility. Results The method has been demonstrated and validated by cyclic bending of Alloy 718plus microcantilevers prepared on a bulk specimen. The experiments reveal that this method is reliable and produces results that are comparable to a nanoindenter setup. Conclusions Due to the flexibility of the method, it offers straightforward testing of cantilevers manufactured at arbitrary position on bulk samples with fully reversed plastic deformation. Specific microstructural features, e.g., selected orientations, grain boundaries, phase boundaries etc., can therefore be easily targeted.

Sign in / Sign up

Export Citation Format

Share Document