Hydrodynamic Lubrication of Journal Bearings with a Polymer Melt

1980 ◽  
Vol 102 (4) ◽  
pp. 858-864
Author(s):  
J. V. Accorsi ◽  
T. A. DeRossett
Keyword(s):  
Power Loss ◽  
Hydrodynamic Lubrication ◽  
Axial Flow ◽  
Polymer Melt ◽  
Pressure Profile ◽  
Journal Bearings ◽  
Test Apparatus ◽  
Eccentricity Ratio ◽  
Newtonian Viscosity ◽  
Rate Relation

An experimental investigation of hydrodynamic lubrication of journal bearings was conducted using a polymer melt as the lubricating fluid. The test apparatus monitored the pressure profile, eccentricity ratio, axial flow rate and frictional power loss for a bearing with L/D = 1.5. Due to the non-Newtonian viscosity/shear-rate relation of the polymer, it was necessary to define a generalized Sommerfeld number in order to plot the data. The results provide a tool for the design of polymer lubricated bearings.

Design of Multi-Recess Hydrostatic Journal Bearings for Minimum Total Power Loss

1974 ◽  
Vol 96 (1) ◽  
pp. 226-232 ◽  
Author(s):  
C. Cusano ◽  
T. F. Conry
Keyword(s):  
Rotational Speed ◽  
Power Loss ◽  
Load Capacity ◽  
Maximum Load ◽  
Journal Bearings ◽  
Design Criterion ◽  
Total Power ◽  
Eccentricity Ratio ◽  
Constant Ratio ◽  
Design Charts

The design problem is formulated for multi-recess hydrostatic journal bearings with a design criterion of minimum total power loss. The design is subject to the constraints of constant ratio of the recess area to the total bearing area and maximum load capacity for a given recess geometry. The L/D ratio, eccentricity ratio, ratio of recess area to total bearing area, and shaft rotational speed are considered as parameters. The analysis is based on the bearing model of Raimondi and Boyd [1]. This model is generally valid for low-to-moderate speeds and a ratio of recess area-to-total bearing area of approximately 0.5 or greater. Design charts are presented for bearings having a ratio of recess area-to-total bearing area of 0.6 and employing capillary and orifice restrictors, these being the most common types of compensating elements. A design example is given to illustrate the use of the design charts.

The Effect of Oil Supply Pressure on the Circumferential Pressure Profile in Hydrodynamic Journal Bearing

2013 ◽  
Vol 315 ◽  
pp. 809-814 ◽  
Author(s):  
Mohamad Ali Ahmad ◽  
Salmiah Kasolang ◽  
Rob Dwyer-Joyce ◽  
Nik Rosli Abdullah
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Pressure Profile ◽  
Journal Bearings ◽  
Maximum Pressure ◽  
Oil Supply ◽  
Supply Pressure ◽  
Machine Elements ◽  
Hydrodynamic Journal Bearing ◽  
Circumferential Pressure

In hydrodynamic lubrication, the pressure condition of the fluid is critical to ensure good performance of the lubricated machine elements such as journal bearings. In the present study, an experimental work was conducted to determine the effect of oil supply pressure on pressure profile around the circumference of a journal bearing. A journal diameter of 100mm with a ½ length-to-diameter ratio was used. The oil supply pressure was set at three different values (0.3, 0.5, 0.7 Mpa) and the circumferential pressure results for 400, 600 and 800 RPM at different radial loads were obtained. It was observed that the maximum pressure values were affected by changes in oil supply pressure.

scholarly journals Numerical Analysis of a Hydrodynamic Herringbone Grooved Journal Bearing

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
D. Souchet ◽  
A. Senouci ◽  
H. Zaidi ◽  
M. Amirat
Keyword(s):  
Reynolds Equation ◽  
Journal Bearing ◽  
Numerical Study ◽  
Hydrodynamic Lubrication ◽  
Dynamical Behavior ◽  
Axial Flow ◽  
Journal Bearings ◽  
Film Rupture ◽  
High Rotational Speed ◽  
Fluid Leakage

In hydrodynamic lubrication, at very high rotational speed, the phenomenon of axial fluid leakage is often present. This can involve an increase of shear stress in the contact and consequently a considerable increase of the temperature. For that and in order to solve this problem, we took interest in the herringbone grooved journal bearings. The researches made before on these types of groove bearing have shown that they present a good dynamical behavior with a low eccentricity and a low axial flow. In this paper, a numerical study of a herringbone journal bearing operating behavior, under laminar and isothermal regime, is presented. The theoretical model, based on the classical Reynolds equation, is used. In order to include the film rupture and reformation, the Reynolds equation is modified using a mass conservative algorithm. To understand the behavior of these herringbone grooved journal bearings well, numerical modeling, using finite element method, has been developed. Various geometrical shapes of the herringbone grooved journal bearings have been analyzed, allowing us to limit the fluid leakage problem, by working particularly on the contact form.

Feasibility of Gas-Expanded Lubricants for Increased Energy Efficiency in Tilting-Pad Journal Bearings

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Andres Clarens ◽  
Amir Younan ◽  
Shibo Wang ◽  
Paul Allaire
Keyword(s):  
Supercritical Co2 ◽  
Power Loss ◽  
Load Capacity ◽  
Reducing Power ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Eccentricity Ratio ◽  
Power Losses ◽  
Tilting Pad ◽  
Tilting Pad Journal Bearings

Lubricants are necessary in tilting-pad journal bearings to ensure separation between solid surfaces and to dissipate heat. They are also responsible for much of the undesirable power losses that can occur through a bearing. Here, a novel method to reduce power losses in tilting-pad journal bearings is proposed in which the conventional lubricant is substituted by a binary mixture of synthetic lubricant and dissolved CO2. These gas-expanded lubricants (GELs) would be delivered to a reinforced bearing housing capable of withstanding modest pressures less than 10 MPa. For bearings subject to loads that are both variable and predictable, GELs could be used to adjust lubricant properties in real time. High-pressure lubricants, mostly gases, have already been explored in tilting-pad journal bearings as a means to accommodate higher shaft speeds while reducing power losses and eliminating the potential for thermal degradation of the lubricant. These gas-lubricated bearings have intrinsic limitations in terms of bearing size and load capacity. The proposed system would combine the loading capabilities of conventional lubricated bearings with the efficiency of gas-lubricated bearings. The liquid or supercritical CO2 serves as a low-viscosity and completely miscible additive to the lubricant that can be easily removed by purging the gas after releasing the pressure. In this way, the lubricant can be fully recycled, as in conventional systems, while controlling the lubricant properties dynamically by adding liquid or supercritical CO2. Lubricant properties of interest, such as viscosity, can be easily tuned by controlling the pressure inside the bearing housing. Experimental measurements of viscosity for mixtures of polyalkylene glycol (PAG)+CO2 at various compositions demonstrate that significant reductions in mixture viscosity can be achieved with relatively small additions of CO2. The measured parameters are used in a thermoelastohydrodynamic model of tilting-pad journal bearing performance to evaluate the bearing response to GELs. Model estimates of power loss, eccentricity ratio, and pad temperature suggest that bearings would respond quite favorably over a range of speed and preload conditions. Calculated power loss reductions of 20% are observed when compared with both a reference petroleum lubricant and PAG without CO2. Pad temperature is also maintained without significant increases in eccentricity ratio. Both power loss and pad temperature are directly correlated with PAG-CO2 composition, suggesting that these mixtures could be used as “smart” lubricants responsive to system operating conditions.

Load Carrying Efficiency of Floating Ring Journal Bearings

1983 ◽  
Vol 105 (4) ◽  
pp. 605-607 ◽  
Author(s):  
D. F. Wilcock
Keyword(s):  
External Load ◽  
Power Loss ◽  
Full Range ◽  
Journal Bearings ◽  
Length Ratio ◽  
Eccentricity Ratio ◽  
Clearance Ratio ◽  
Isothermal Conditions ◽  
Load Carrying

Floating ring bearings are compared to single film journal bearings over the full range from laminar to turbulent conditions in the films. Isothermal conditions are assumed. Assuming each type carries the same external load and operates at the same eccentricity ratio as determined by the Capacity Number, reductions in the power loss required range from 31 to 64 percent when the clearance ratio C0/(C1 + C2) is held constant and the length is shortened, and from 42 to 63 percent when the length ratio L0/L is held constant and the clearance ratio C0/(C1 + C2) is reduced. Equilibrium ring speeds range from ω0/3 to 0.45 ω0.

Analysis of Pneumatic Instability of Externally Pressurized Porous Gas Journal Bearings

1979 ◽  
Vol 101 (1) ◽  
pp. 48-53 ◽  
Author(s):  
N. S. Rao ◽  
B. C. Majumdar
Keyword(s):  
Theoretical Analysis ◽  
Mass Parameter ◽  
Journal Bearings ◽  
Order Perturbation ◽  
Rigid Rotor ◽  
Eccentricity Ratio ◽  
Dynamic Displacement ◽  
First Order ◽  
Supply Pressure ◽  
First Order Perturbation

A theoretical analysis is presented for the study of pneumatic instability for a rigid rotor supported in externally pressurized porous gas journal bearings. The analysis is based on a first-order perturbation with respect to the amplitude of dynamic displacement of rotor. The variation of threshold mass parameter with feeding parameter is shown. In addition, the effects of supply pressure, eccentricity ratio, L/D ratio, and porosity parameter are investigated and presented in the form of graphs.

Theoretical Prediction of the Lift-Off Speed in Aerodynamic Compliant Foil Journal Bearings

2010 ◽  
Author(s):  
Shemiao Qi ◽  
Y. S. Ho ◽  
Haipeng Geng ◽  
Lie Yu
Keyword(s):  
Theoretical Prediction ◽  
Generalized Solution ◽  
Journal Bearings ◽  
Numerical Results ◽  
Computational Method ◽  
Radial Clearance ◽  
Eccentricity Ratio ◽  
Foil Bearings ◽  
Lift Off ◽  
Air Film

In aerodynamic bearings, since the supporting air film is generated by rotor motion, there is no support at the start of motion. As in all such bearings, there is dry rubbing until the rotor achieves sufficient speed to lift-off. Thus, the lower the lift-off speed, the less will be the rubbing and so the greater will be the life of the bearing. This paper focuses on the theoretical prediction of lift-off speed in aerodynamic compliant foil journal bearings based on a generalized solution of elasto-aerodynamically coupled lubrication for compliant foil bearings. A computational method is presented which is used to predict the lift-off speed in aerodynamic foil journal bearings with eccentricity ratio greater than or equal to 1.0. Special emphasis is placed on investigating the effects of the load imposed on the bearing, the nominal radial clearance and the bearing radius on the lift-off speed. The numerical results obtained indicate that lift-off speed decreases with the decrease of load and nominal radial clearance, but with an increase in bearing radius. The eccentricity ratios are all greater than 1.0 at the lift-off speed for the aerodynamic compliant foil journal bearings used in this study.

Lubrication of Porous Journal Bearings

1972 ◽  
Vol 94 (1) ◽  
pp. 69-73 ◽  
Author(s):  
C. Cusano
Keyword(s):  
Analytical Solution ◽  
Coefficient Of Friction ◽  
Load Capacity ◽  
Journal Bearings ◽  
Performance Characteristics ◽  
Eccentricity Ratio ◽  
Design Variables

An analytical solution for the performance characteristics of finite porous journal bearings is obtained. Results are presented which relate the eccentricity ratio and coefficient of friction as functions of load number for design variables of 0.0001, 0.001, 0.01, and 0.1. The load capacity obtained by using the finite bearing theory is compared to the load capacity obtained by using the short-bearing approximation and the infinite-bearing approximation.

Sign in / Sign up

Export Citation Format

Share Document