scholarly journals Discussion: “Surface Topography Changes in Polymer-Metal Sliding—II” (Jain, V. K., and Bahadur, S., 1983, ASME J. Lubr. Technol., 105, pp. 526–531)

1983 ◽  
Vol 105 (4) ◽  
pp. 531-532
Author(s):  
N. S. Eiss
Keyword(s):  
Surface Topography ◽  
Polymer Metal

Surface Topography Changes in Polymer-Metal Sliding - I

1980 ◽  
Vol 102 (4) ◽  
pp. 520-525 ◽  
Author(s):  
V. K. Jain ◽  
S. Bahadur
Keyword(s):  
Steady State ◽  
Surface Topography ◽  
Radius Of Curvature ◽  
Unsteady State ◽  
Surface Parameters ◽  
Point Analysis ◽  
Stable Conditions ◽  
Steel Disc ◽  
Polymer Metal ◽  
Surface Profiles

The adhesive wear of polymers, sliding against smooth metal surfaces, is influenced by the manner in which the surface topography of sliding surfaces is modified. The variation in the surface topographical parameters with sliding between a ground steel disc and a poly(methyl methacrylate) pin was, therefore, investigated for both the unsteady state and steady state wear conditions. The surface profiles of the unrubbed and rubbed metal disc were recorded, using a profilometer, both along and perpendicular to the direction of sliding. From the profile ordinate data read at 10 μm intervals, the surface roughness parameters, namely, the rms and c.l.a. roughness, asperity radius of curvature, asperity density, and average asperity slope were calculated using a computer program. Three point analysis was used to define a peak and compute the asperity slope and radius of curvature. The distributions of surface parameters were determined using a Weibull distribution approach. The analysis showed that the surface parameters have a large initial variation followed by more or less stable conditions, which explains the transition of unsteady state wear to steady state wear. The changes on the disc surface perpendicular to the sliding direction are minimal. The rms roughness and the average asperity slope were found to have a linear relationship.

The Broad Applications of the Scanning Electron Microscope

1969 ◽  
Vol 27 ◽  
pp. 20-21
Author(s):  
C. T. Nightingale ◽  
S. E. Summers ◽  
T. P. Turnbull
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Light Microscopy ◽  
Surface Topography ◽  
Great Depth ◽  
Resolving Power ◽  
Depth Of Field ◽  
Pictorial Representations ◽  
Scanning Electron

The ease of operation of the scanning electron microscope has insured its wide application in medicine and industry. The micrographs are pictorial representations of surface topography obtained directly from the specimen. The need to replicate is eliminated. The great depth of field and the high resolving power provide far more information than light microscopy.

Effects of Ion Beam Milling on Surface Topography

1973 ◽  
Vol 31 ◽  
pp. 84-85
Author(s):  
P.G. Pawar ◽  
P. Duhamel ◽  
G.W. Monk
Keyword(s):  
Surface Topography ◽  
Ion Beam ◽  
Solid Material ◽  
Beam Current ◽  
Atomic Mass ◽  
Micro Milling ◽  
Ion Milling ◽  
Controlled Atmospheres ◽  
Milling Operations ◽  
Sufficient Energy

A beam of ions of mass greater than a few atomic mass units and with sufficient energy can remove atoms from the surface of a solid material at a useful rate. A system used to achieve this purpose under controlled atmospheres is called an ion miliing machine. An ion milling apparatus presently available as IMMI-III with a IMMIAC was used in this investigation. Unless otherwise stated, all the micro milling operations were done with Ar+ at 6kv using a beam current of 100 μA for each of the two guns, with a specimen tilt of 15° from the horizontal plane.It is fairly well established that ion bombardment of the surface of homogeneous materials can produce surface topography which resembles geological erosional features.

Low-Loss Images in a Stem/Tem Microscope

1976 ◽  
Vol 34 ◽  
pp. 496-497 ◽  
Author(s):  
David C. Joy ◽  
Dennis M. Maher
Keyword(s):  
High Resolution ◽  
Surface Topography ◽  
Beam Direction ◽  
Low Loss ◽  
Specimen Holder ◽  
Glancing Angle ◽  
High Resolution Images ◽  
Set Up ◽  
Conventional Manner ◽  
Objective Type

High-resolution images of the surface topography of solid specimens can be obtained using the low-loss technique of Wells. If the specimen is placed inside a lens of the condenser/objective type, then it has been shown that the lens itself can be used to collect and filter the low-loss electrons. Since the probeforming lenses in TEM instruments fitted with scanning attachments are of this type, low-loss imaging should be possible.High-resolution, low-loss images have been obtained in a JEOL JEM 100B fitted with a scanning attachment and a thermal, fieldemission gun. No modifications were made to the instrument, but a wedge-shaped, specimen holder was made to fit the side-entry, goniometer stage. Thus the specimen is oriented initially at a glancing angle of about 30° to the beam direction. The instrument is set up in the conventional manner for STEM operation with all the lenses, including the projector, excited.

A procedure for cross-sectioning materials for TEM analysis without ion milling

1990 ◽  
Vol 48 (4) ◽  
pp. 742-743
Author(s):  
J.P. Benedict ◽  
Ron Anderson ◽  
S. J. Klepeis
Keyword(s):  
Surface Topography ◽  
Milling Time ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Cleaning Operation ◽  
Tem Analysis ◽  
Platinum Silicide ◽  
Surface Alteration ◽  
Polishing Damage ◽  
Tools And Methods

Traditional specimen preparation procedures for non-biological samples, especially cross section preparation procedures, involves subjecting the specimen to ion milling for times ranging from minutes to tens of hours. Long ion milling time produces surface alteration, atomic number and rough-surface topography artifacts, and high temperatures. The introduction of new tools and methods in this laboratory improved our ability to mechanically thin specimens to a point where ion milling time was reduced to one to ten minutes. Very short ion milling times meant that ion milling was more of a cleaning operation than a thinning operation. The preferential thinning and the surface topography that still existed in briefly ion milled samples made the study of interfaces between materials such as platinum silicide and silicon difficult. These two problems can be eliminated by completely eliminating the ion milling step and mechanically polishing the sample to TEM transparency with the procedure outlined in this communication. Previous successful efforts leading to mechanically thinned specimens have shown that problems center on tool tilt control, removal of polishing damage, and specimen cleanliness.

Sign in / Sign up

Export Citation Format

Share Document