scholarly journals Discussion: “Experimental Evaluation of a Mixed Friction Hydrostatic Mechanical Face Seal Model Considering Radial Taper, Thermal Taper, and Wear” (Young, L. A., and Lebeck, A. O., 1982, ASME J. Lubr. Technol., 104, pp. 439–447)

1982 ◽  
Vol 104 (4) ◽  
pp. 447-448
Author(s):  
I. Etsion
Keyword(s):  
Experimental Evaluation ◽  
Face Seal ◽  
Mixed Friction ◽  
Mechanical Face Seal

Experimental Evaluation of a Mixed Friction Hydrostatic Mechanical Face Seal Model Considering Radial Taper, Thermal Taper, and Wear

1982 ◽  
Vol 104 (4) ◽  
pp. 439-447 ◽  
Author(s):  
L. A. Young ◽  
A. O. Lebeck
Keyword(s):  
Surface Roughness ◽  
Radial Profile ◽  
Surface Characteristics ◽  
Experimental Investigations ◽  
Test Duration ◽  
Face Seal ◽  
Mixed Friction ◽  
Face Seals ◽  
Water Test ◽  
Mechanical Face Seal

In this paper the results of experimental investigations of the effects of radial taper on mechanical face seals are presented and compared to theory. The previously published theory considers the effects of thermal taper caused by a temperature gradient in the seal rings; mixed friction in the case where load support is shared between hydrostatic support and partial contact of the seal faces; surface roughness, which affects both load sharing and leakage; and wear, which alters the radial profile. Fifteen tests were run using a 100 mm diameter carbon versus tungsten carbide seal at 1800 rpm and 3.45 MPa in water. Test duration was up to 100 hr. Varying amounts of radial taper were used. Tests were run at balance ratios of 1.00 and 0.75. Initial and final surface profiles were recorded. Seal torque, leakage, and face temperatures were recorded as functions of time. Results show that theory predicts initial torque and leakage as functions of initial taper quite well, given knowledge of seal surface characteristics. Predicted equilibrium thermal taper as a function of torque for a balance ratio of 1.0 is good. For a seal having a balance ratio of 0.75, predicted equilibrium thermal rotation shows some agreement but more experimental data are needed. The results of 1.00 balance ratio tests suggest that after a long period of operation, any initial taper will be worn away and the seal would continue to operate as a parallel face seal. Results from long-term tests indicate that the wear coefficient is not a constant. While the experimental results support the basic concepts of the model, the results show where further work must be done to better understand the role of surface roughness and wear processes in mechanical face seals.

A Mixed Friction Hydrostatic Face Seal Model With Phase Change

1980 ◽  
Vol 102 (2) ◽  
pp. 133-138 ◽  
Author(s):  
A. O. Lebeck
Keyword(s):  
Phase Change ◽  
Design Parameters ◽  
Face Seal ◽  
Mechanical Contact ◽  
Two Phase ◽  
Mixed Friction ◽  
Mechanical Face Seal ◽  
Higher Temperature ◽  
And Performance ◽  
Very High

A mixed friction hydrostatic mechanical face seal model is presented. Load support and friction due to mechanical contact and the effect of a phase change are considered. The results show that a phase change within the seal interface leads to a greater fraction of the load being supported by fluid film pressure than for an all liquid or all gas phase seal. As seal operating temperature approaches the boiling point of the sealed fluid, very high leakage is predicted. An explanation for puffing is offered. The effect of various design parameters on two phase seal operation is examined. On a theoretical basis, operation at a higher temperature reduces seal wear rate and friction. The model can be used by seal designers to predict instability and performance for a two phase seal.

Thermoelastohydrodynamic Behavior of Mechanical Gas Face Seals Operating at High Pressure

2007 ◽  
Vol 129 (4) ◽  
pp. 841-850 ◽  
Author(s):  
Sébastien Thomas ◽  
Noël Brunetière ◽  
Bernard Tournerie
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Numerical Modeling ◽  
Face Seal ◽  
Inertia Effects ◽  
Real Gas ◽  
Choked Flow ◽  
Face Seals ◽  
Mechanical Face Seal ◽  
Gas Expansion

A numerical modeling of thermoelastohydrodynamic mechanical face seal behavior is presented. The model is an axisymmetric one and it is confined to high pressure compressible flow. It takes into account the behavior of a real gas and includes thermal and inertia effects, as well as a choked flow condition. In addition, heat transfer between the fluid film and the seal faces is computed, as are the elastic and thermal distortions of the rings. In the first part of this paper, the influence of the coning angle on mechanical face seal characteristics is studied. In the second part, the influence of the solid distortions is analyzed. It is shown that face distortions strongly modify both the gap geometry and the mechanical face seal’s performance. The mechanical distortions lead to a converging gap, while the gas expansion, by cooling the fluid, creates a diverging gap.

scholarly journals Lubrication and Wear Characteristics of Mechanical Face Seals under Random Vibration Loading

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1285
Author(s):  
Wentao He ◽  
Shaoping Wang ◽  
Chao Zhang ◽  
Xi Wang ◽  
Di Liu
Keyword(s):  
Dynamic Model ◽  
Random Vibration ◽  
Experimental Studies ◽  
Lumped Parameter Model ◽  
Axial Stiffness ◽  
Face Seal ◽  
Wear Characteristics ◽  
Vibration Loading ◽  
Face Seals ◽  
Mechanical Face Seal

The service life of mechanical face seals is related to the lubrication and wear characteristics. The stable analytical methods are commonly used, but they cannot address effects of random vibration loading, which, according to experimental studies, are important factors for lubrication and wear of mechanical face seals used in air and space vehicles. Hence, a dynamic model for mechanical face seals is proposed, with a focus on the effects of random vibration loading. The mechanical face seal in the axial direction is described as a mass-spring-damping system. Spectrum analysis specified for random vibration is then performed numerically to obtain the response power spectral density (PSD) of the mechanical face seal and calculate the root mean square (RMS) values under random vibration conditions. A lumped parameter model is then developed to examine how dynamic parameters such as stiffness and damping affect the lubrication regimes of mechanical face seals. Based on the dynamic model and Archard wear equation, a numerical wear simulation method is proposed. The results elucidated that the increase of input acceleration PSDs, the decrease of axial damping, and the increase of axial stiffness lead to the probability of the mechanical face seal operating under full film lubrication regime increase and finally the decrease of wear. This research provides a guideline for improving the adaptability of mechanical face seals under random vibration environments.

Sign in / Sign up

Export Citation Format

Share Document