Closure to “Discussions of ‘Endurance Tests With Large-Bore Tapered-Roller Bearings to 2.2 Million DN’” (1982, ASME J. Lubr. Technol., 104, pp. 298–299)

1982 ◽  
Vol 104 (3) ◽  
pp. 299-299 ◽  
Author(s):  
R. J. Parker ◽  
H. R. Signer ◽  
S. I. Pinel
Keyword(s):  
Roller Bearings ◽  
Endurance Tests ◽  
Tapered Roller ◽  
Tapered Roller Bearings

scholarly journals Endurance Tests With Large-Bore Tapered-Roller Bearings to 2.2 Million DN

1982 ◽  
Vol 104 (3) ◽  
pp. 293-298 ◽  
Author(s):  
R. J. Parker ◽  
H. R. Signer ◽  
S. I. Pinel
Keyword(s):  
High Speed ◽  
Roller Bearings ◽  
Standard Design ◽  
Endurance Tests ◽  
Life Tests ◽  
Tapered Roller ◽  
High Speed Design ◽  
Tapered Roller Bearings ◽  
Hoop Stresses ◽  
Thrust Load

Endurance life tests were run with standard design and optimized high-speed design 120.65-mm- (4.750-in.-) bore tapered-roller bearings at shaft speeds of 12,500 and 18,500 rpm, respectively. Standard design bearings of vacuum melted AISI 4320 and CBS-1000M, and high-speed design bearings of CBS-1000M and through-hardened AISI M-50 were run under heavy combined radial and thrust load until fatigue failure or until a preset cutoff time of 1100 hours was reached. Standard design bearings made from CBS 1000M material ran to a 10-percent life approximately six times rated catalog life. Twelve identical bearings of AISI 4320 material ran to ten times rated calalog life without failure. Cracking and fracture of the cones of AISI M-50 high-speed design bearings occurred at 18,500 rpm due to high tensile hoop stresses. Four CBS 1000M high-speed design bearings ran to twenty-four times rated catalog life without any spalling, cracking or fracture failures.

scholarly journals Geometrical Optimization of the EHL Roller Face/Rib Contact for Energy Efficiency in Tapered Roller Bearings

Lubricants ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 67
Author(s):  
Sven Wirsching ◽  
Max Marian ◽  
Marcel Bartz ◽  
Thomas Stahl ◽  
Sandro Wartzack
Keyword(s):  
Energy Efficiency ◽  
Carrying Capacity ◽  
Tribological Behavior ◽  
Large Radius ◽  
Load Carrying Capacity ◽  
Statistical Design Of Experiments ◽  
Roller Bearings ◽  
Load Carrying ◽  
Tapered Roller ◽  
Tapered Roller Bearings

In the context of targeted improvements in energy efficiency, secondary rolling bearing contacts are gaining relevance. As such, the elastohydrodynamically lubricated (EHL) roller face/rib contact of tapered roller bearings significantly affects power losses. Consequently, this contribution aimed at numerical optimization of the pairing’s macro-geometric parameters. The latter were sampled by a statistical design of experiments (DoE) and the tribological behavior was predicted by means of EHL contact simulations. For each of the geometric pairings considered, a database was generated. Key target variables such as pressure, lubricant gap and friction were approximated by a meta-model of optimal prognosis (MOP) and optimization was carried out using an evolutionary algorithm (EA). It was shown that the tribological behavior was mainly determined by the basic geometric pairing and the radii while eccentricity was of subordinate role. Furthermore, there was a trade-off between high load carrying capacity and low frictional losses. Thereby, spherical or toroidal geometries on the roller end face featuring a large radius paired with a tapered rib geometry were found to be advantageous in terms of low friction. For larger lubricant film heights and load carrying capacity, spherical or toroidal roller on toroidal rib geometries with medium radii were favorable.

Tandem tapered roller bearings no-load torque loss in a rear axle gear transmission

2021 ◽  
Vol 157 ◽  
pp. 106876
Author(s):  
Justino A.O. Cruz ◽  
Pedro M.T. Marques ◽  
Jorge H.O. Seabra ◽  
Ramiro C. Martins
Keyword(s):  
Rear Axle ◽  
Gear Transmission ◽  
Load Torque ◽  
Roller Bearings ◽  
Torque Loss ◽  
Tapered Roller ◽  
Tapered Roller Bearings

scholarly journals In-Process Measurement for the Process Control of the Real-Time Manufacturing of Tapered Roller Bearings

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1371 ◽  
Author(s):  
Francisco Brosed ◽  
A. Zaera ◽  
Emilio Padilla ◽  
Fernando Cebrián ◽  
Juan Aguilar
Keyword(s):  
Real Time ◽  
Measurement Procedure ◽  
Axial Loads ◽  
Machining Processes ◽  
Process Measurement ◽  
Roller Bearings ◽  
Tapered Roller ◽  
Environmental Process ◽  
Tapered Roller Bearings ◽  
Component Assembly

Tapered roller bearings can accommodate high radial loads as well as high axial loads. The manufacturing process consists of machining processes for ring and component assembly. In this contribution, the parameters of influence on the measurement procedure were studied. These parameters of influence were classified as environmental, process, and machine parameters. The main objective of this work was to optimize the process using real-time measurements, which required the study of the influence of several parameters on the measurement uncertainty and how to correct their effects.

Sign in / Sign up

Export Citation Format

Share Document