On The Steady State and Dynamic Performance Characteristics of Floating Ring Bearings

1981 ◽  
Vol 103 (3) ◽  
pp. 389-397 ◽  
Author(s):  
Chin-Hsiu Li ◽  
S. M. Rohde
Keyword(s):  
Steady State ◽  
Linear Theory ◽  
High Speed ◽  
Dynamic Performance ◽  
Equations Of Motion ◽  
Nonlinear Behavior ◽  
Journal Bearings ◽  
Transient Problem ◽  
The Stability ◽  
Bearing System

An analysis of the steady state and dynamic characteristics of floating ring journal bearings has been performed. The stability characteristics of the bearing, based on linear theory, are given. The transient problem, in which the equations of motion for the bearing system are integrated in real time was studied. The effect of using finite bearing theory rather than the short bearing assumption was examined. Among the significant findings of this study is the existence of limit cycles in the regions of instability predicted by linear theory. Such results explain the superior stability characteristics of the floating ring bearing in high speed applications. An understanding of this nonlinear behavior, serves as the basis for new and rational criteria for the design of floating ring bearings.

Stability of Multirecess Hybrid-Operating Oil Journal Bearings

1985 ◽  
Vol 107 (1) ◽  
pp. 116-121 ◽  
Author(s):  
Y. S. Chen ◽  
H. Y. Wu ◽  
P. L. Xie
Keyword(s):  
Finite Difference Method ◽  
Dynamic Performance ◽  
Journal Bearings ◽  
Design Parameters ◽  
Stability Threshold ◽  
Damping Coefficients ◽  
Hybrid Bearing ◽  
The Stability ◽  
Stiffness And Damping ◽  
Bearing System

An analysis and a numerical solution using finite difference method to predict the dynamic performance of multirecess hybrid-operating oil journal bearings are presented. The linearized stiffness and damping coefficients of a typical capillary-compensated bearing with four recesses are computed for various design parameters. The corresponding stiffness and the stability threshold of the bearing are then obtained, and the opposite influences of the hydrodynamic action on them are demonstrated. The effect of rotor flexibility on the onset of self-excited whirl is discussed, and a method is given to determine the stability threshold of a rotor-hybrid bearing system.

Performance of Two Lobe Multirecess Hybrid Journal Bearing Compensated With Capillary Restrictor

2007 ◽  
Author(s):  
Prashant Kushare ◽  
Satish C. Sharma ◽  
S. C. Jain ◽  
J. Sharana Basavaraja
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Dynamic Performance ◽  
Journal Bearings ◽  
Performance Characteristics ◽  
Favourable Effect ◽  
Improved Performance ◽  
Stiffness And Damping ◽  
Offset Factor ◽  
Bearing System

Multirecess hydrostatic/hybrid journal bearings are being used in many applications owing to their excellent characteristics. The Noncircular journal bearing configurations too are quite frequently used in high speed machinery as they are efficient, less costly and provide better shaft stability. The Two lobe bearing (elliptical bearing) are among the commonly used noncircular journal bearing configuration. The multilobe multirecess hybrid journal bearings have been developed to combine the features of noncircular and circular hybrid journal bearing configurations. In the present work a theoretical investigation of a two lobe multirecess hydrostatic/hybrid journal bearing system have been carried out. The multilobe journal bearing configuration is designed as an arc of the circle with the centre points placed on the symmetry line of the single lobe. The journal offset has been accounted by defining an offset factor ‘δ’. The finite element method has been used to solve the Reynolds equation governing the flow of lubricant in the clearance space of the journal bearing system. The bearing static and dynamic performance characteristics have been presented for the various values of the offset factors (0.75, 1, 1.25 and 1.50) for hybrid mode of operation of the bearing. The simulated results of the studies reveals that, a two lobe recessed hybrid journal bearing provides an improved performance in respect of fluid film stiffness and damping coefficients as compared to that of circular recessed journal bearing. It has been observed that for a multilobe bearing having offset factor more than one has a favourable effect on the dynamic performance characteristics of the two lobe bearing.

Dynamic Performance of High-Speed Electric Multiple Unit within Multi-Body System Simulation

2019 ◽  
Vol 12 (4) ◽  
pp. 339-349
Author(s):  
Junguo Wang ◽  
Daoping Gong ◽  
Rui Sun ◽  
Yongxiang Zhao
Keyword(s):  
High Speed ◽  
Rapid Development ◽  
Dynamic Performance ◽  
Body System ◽  
High Speed Railway ◽  
Evaluation Indexes ◽  
Actual Operation ◽  
Multiple Unit ◽  
The Stability ◽  
Multi Body

Background: With the rapid development of the high-speed railway, the dynamic performance such as running stability and safety of the high-speed train is increasingly important. This paper focuses on the dynamic performance of high-speed Electric Multiple Unit (EMU), especially the dynamic characteristics of the bogie frame and car body. Various patents have been discussed in this article. Objective: To develop the Multi-Body System (MBS) model of EMU, verify whether the dynamic performance meets the actual operation requirements, and provide some useful information for dynamics and structural design of the proposed EMU. Methods: According to the technical characteristics of a typical EMU, a MBS model is established via SIMPACK, and the measured data of China high-speed railway is taken as the excitation of track random irregularity. To test the dynamic performance of the EMU, including the stability and safety, some evaluation indexes such as wheel-axle lateral forces, wheel-axle lateral vertical forces, derailment coefficients and wheel unloading rates are also calculated and analyzed in detail. Results: The MBS model of EMU has better dynamic performance especially curving performance, and some evaluation indexes of the stability and safety have also reached China’s high-speed railway standards. Conclusion: The effectiveness of the proposed MBS model is verified, and the dynamic performance of the MBS model can meet the design requirements of high-speed EMU.

Non-linear stability analysis of micropolar fluid lubricated journal bearings with turbulent effect

2019 ◽  
Vol 71 (1) ◽  
pp. 31-39
Author(s):  
Subrata Das ◽  
Sisir Kumar Guha
Keyword(s):  
Stability Analysis ◽  
Linear Stability ◽  
Micropolar Fluid ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Turbulent Regime ◽  
Content Type ◽  
Non Linear ◽  
The Stability ◽  
Bearing System

Purpose The purpose of this paper is to investigate the effect of turbulence on the stability characteristics of finite hydrodynamic journal bearing lubricated with micropolar fluid. Design/methodology/approach The non-dimensional transient Reynolds equation has been solved to obtain the non-dimensional pressure field which in turn used to obtain the load carrying capacity of the bearing. The second-order equations of motion applicable for journal bearing system have been solved using fourth-order Runge–Kutta method to obtain the stability characteristics. Findings It has been observed that turbulence has adverse effect on stability and the whirl ratio at laminar flow condition has the lowest value. Practical implications The paper provides the stability characteristics of the finite journal bearing lubricated with micropolar fluid operating in turbulent regime which is very common in practical applications. Originality/value Non-linear stability analysis of micropolar fluid lubricated journal bearing operating in turbulent regime has not been reported in literatures so far. This paper is an effort to address the problem of non-linear stability of journal bearings under micropolar lubrication with turbulent effect. The results obtained provide useful information for designing the journal bearing system for high speed applications.

Bifurcation Theory Applied to Oil Whirl in Plain Cylindrical Journal Bearings

1984 ◽  
Vol 51 (2) ◽  
pp. 244-250 ◽  
Author(s):  
C. J. Myers
Keyword(s):  
Steady State ◽  
Hopf Bifurcation ◽  
Equilibrium Position ◽  
Small Amplitude ◽  
Bifurcation Theory ◽  
Equations Of Motion ◽  
Journal Bearings ◽  
The Self ◽  
Oil Whirl ◽  
Nonlinear Equations Of Motion

An analysis of the self-excited oscillations of a rotor supported in fluid film journal bearings is presented. It is shown that Hopf bifurcation theory may be used to investigate small-amplitude periodic solutions of the nonlinear equations of motion for rotor speeds close to the speed at which the steady-state equilibrium position becomes unstable. A numerical investigation supports the findings of the analytic work.

Non-Linear Transient Stability Analysis of a Rigid Rotor Supported on Journal Bearings With Rectangular Dimples

2015 ◽  
Author(s):  
Ram Turaga
Keyword(s):  
Stability Analysis ◽  
Surface Texture ◽  
Transient Stability ◽  
Equations Of Motion ◽  
Journal Bearings ◽  
Pressure Curve ◽  
Rigid Rotor ◽  
Non Linear ◽  
The Stability ◽  
Transient Stability Analysis

The influence of deterministic surface texture on the sub-synchronous whirl stability of a rigid rotor has been studied. Non-linear transient stability analysis has been performed to study the stability of a rigid rotor supported on two symmetric journal bearings with a rectangular dimple of large aspect ratio. The surface texture parameters considered are dimple depth to minimum film thickness ratio and the location of the dimple on the bearing surface. Journal bearings of different Length to diameter ratios have been studied. The governing Reynolds equation for finite journal bearings with incompressible fluid has been solved using the Finite Element Method under isothermal conditions. The trajectories of the journal center have been obtained by solving the equations of motion of the journal center by the fourth-order Runge-Kutta method. When the dimple is located in the raising part of the pressure curve the positive rectangular dimple is seen to decrease the stability whereas the negative rectangular dimple is seen to improve the stability of the rigid rotor.

Dynamic stability of micropolar lubricated hydrodynamic offset-halves journal bearings

2020 ◽  
pp. 135065012093685
Author(s):  
Sanyam Sharma ◽  
Chimata M Krishna
Keyword(s):  
High Speed ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Critical Mass ◽  
Journal Bearings ◽  
Aspect Ratios ◽  
Input Parameters ◽  
Output Characteristics ◽  
The Stability ◽  
Offset Factor

The plain circular journal bearings are not found to be stable by researchers when used in high speed rotating machineries. Hence, extensive research in the study of stability characteristics of non-circular bearings or lobed bearings assumed importance, of late. Present article deals with the stability analysis of non-circular offset bearing by taking selected set of input and output parameters. Modified Reynolds equation for micropolar lubricated rigid journal bearing system is solved using finite element method. Two kinds of input parameters namely, offset factors (0.2, 0.4) and aspect ratios (1.6, 2.0) have been selected for the study. The important output characteristics such as load, critical mass, whirl frequency ratio, and threshold speed are computed and plotted for various set of values of input parameters. The results obtained indicate that micropolar lubricated circular offset bearing is highly stable for higher offset factor and higher aspect ratio.

Analysis of an Accelerating Rotor-Bearing System With Flexible Damped Supports

1998 ◽  
Author(s):  
Euro L. Casanova ◽  
Luis U. Medina
Keyword(s):  
Steady State ◽  
Numerical Integration ◽  
Equations Of Motion ◽  
Peak Amplitude ◽  
Graphical Form ◽  
Jeffcott Rotor ◽  
Rotor Bearing ◽  
Flexible Supports ◽  
Steady State Predictions ◽  
Bearing System

This paper deals with the dynamics of an accelerating unbalanced Jeffcott rotor-bearing system mounted on damped, flexible supports. The general equations of motion for such a system are presented and discussed. The rotor response was predicted, via numerical integration, for various cases in runup and rundown conditions and presented in graphical form. The effects of acceleration on the rotor peak amplitude and the speed at which the peak occurs is discussed and compared to steady state predictions.

On the linear stability analysis of finite-hydrodynamic porous journal bearings under coupled stress lubrication

2007 ◽  
Vol 221 (7) ◽  
pp. 831-840 ◽  
Author(s):  
S. K. Guha ◽  
A. K. Chattopadhyay
Keyword(s):  
Reynolds Equation ◽  
Dynamic Performance ◽  
Slip Flow ◽  
Tangential Velocity ◽  
Continuum Theory ◽  
Transient State ◽  
Velocity Slip ◽  
Journal Bearings ◽  
The Stability ◽  
Coupled Stress

The objective of the present investigation is to study theoretically, using the finite-difference techniques, the dynamic performance characteristics of finite-hydrodynamic porous journal bearings lubricated with coupled stress fluids. In the analysis based on the Stokes micro-continuum theory of the rheological effects of coupled stress fluids, a modified form of Reynolds equation governing the transient-state hydrodynamic film pressures in porous journal bearings with the effect of slip flow of coupled stress fluid as lubricant is obtained. Moreover, the tangential velocity slip at the surface of porous bush has been considered by using Beavers-Joseph criterion. Using the first-order perturbation of the modified Reynolds equation, the stability characteristics in terms of threshold stability parameter and whirl ratios are obtained for various parameters viz. permeability factor, slip coefficient, bearing feeding parameter, and eccentricity ratio. The results show that the coupled stress fluid exhibits better stability in comparison with Newtonian fluid.

Stability Analysis of High-Speed Railway Vehicle Based on Multibody Dynamics Analysis

2013 ◽  
Vol 392 ◽  
pp. 156-160
Author(s):  
Ju Seok Kang
Keyword(s):  
Stability Analysis ◽  
Multibody Dynamics ◽  
High Speed ◽  
Equations Of Motion ◽  
Contact Forces ◽  
Design Parameters ◽  
Railway Vehicle ◽  
Dynamics Analysis ◽  
Contact Points ◽  
The Stability

Multibody dynamics analysis is advantageous in that it uses real dimensions and design parameters. In this study, the stability analysis of a railway vehicle based on multibody dynamics analysis is presented. The equations for the contact points and contact forces between the wheel and the rail are derived using a wheelset model. The dynamics equations of the wheelset are combined with the dynamics equations of the other parts of the railway vehicle, which are obtained by general multibody dynamics analysis. The equations of motion of the railway vehicle are linearized by using the perturbation method. The eigenvalues of these linear dynamics equations are calculated and the critical speed is found.

Sign in / Sign up

Export Citation Format

Share Document