Friction and Heat Transfer Characteristics of Helical Turbulent Air Flow in Annuli

1989 ◽  
Vol 111 (2) ◽  
pp. 337-344 ◽  
Author(s):  
N. S. Gupte ◽  
A. W. Date
Keyword(s):  
Heat Transfer ◽  
Swirl Flow ◽  
Twisted Tape ◽  
Pumping Power ◽  
Poor Agreement ◽  
Principle Of Superposition ◽  
Pressure Drops ◽  
Transfer Rates ◽  
Turbulent Air Flow ◽  
Heat And Momentum Transfer

Friction and Nusselt number data have been measured and semi-empirically evaluated for twisted tape generated helical flow in annuli. Results have been obtained for radius ratios of 0.41 and 0.61 and twist ratios of ∞, 5.302, 5.038, and 2.659. The increase in pressure drop and heat transfer rates obtained are comparable to those reported for twisted tape generated swirl flow in tubes. Also, for the same heat transfer rates the pumping power requirements compare favorably with those for empty annuli. The analytical predictions based on the principle of superposition of pressure drops and analogy between heat and momentum transfer have yielded excellent predictions for y = ∞ and 5.302 but somewhat poor agreement at y = 2.659.

scholarly journals Execution of a Smart Prediction Tool to Evaluate Thermal Performance in a heat exchanger by using Single Elliptical Leaf Strips with altered Angle

2019 ◽  
Vol 8 (11) ◽  
pp. 123-131
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
Industrial Applications ◽  
Generalized Regression Neural Network ◽  
Prediction Tool ◽  
Pressure Drops ◽  
Transfer Rates ◽  
Mass Flow Rates

Heat exchangers are prominent industrial applications where engineering science of heat transfer and Mass transfer occurs. It is a contrivance where transfer of energy occurs to get output in the form of energy transfer. This paper aims at finding a solution to improve the thermal performance in a heat exchanger by using passive method techniques. This experimental and numerical analysis deals with finding the temperature outlets of cold and hot fluid for different mass flow rates and also pressure drop in the tube and the annular side by adding an elliptical leaf strip in the pipe at various angles. The single elliptical leaf used in experiment has major to minor axes ratios as 2:1 and distance of 50 mm between two leaves are arranged at different angular orientations from 0 0 to 1800 with 100 intervals. Since it’s not possible to find the heat transfer rates and pressure drops at every orientation of elliptical leaf so a generalized regression neural network (GRNN) prediction tool is used to get outputs with given inputs to avoid experimentation. GRNN is a statistical method of determining the relationship between dependent and independent variables. The values obtained from experimentation and GRNN nearly had precise values to each other. This analysis is a small step in regard with encomiastic approach for enhancement in performance of heat exchangers

Influence of Short Helical Tape on Local Convective Heat Transfer and Thermal Performance Characteristics in Turbulent Decaying Swirl Flow

2010 ◽  
Vol 8 (1) ◽  
Author(s):  
Smith Eiamsa-ard ◽  
Vichan Kongkaitpaiboon ◽  
Khwanchit Wongcharee
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Thermal Performance ◽  
Swirl Flow ◽  
Transfer Rates ◽  
Friction Factors ◽  
Plain Tube ◽  
Uniform Wall ◽  
Uniform Wall Heat Flux

This paper reports the experimental investigation of local convective heat transfer enhancement, flow friction and thermal performance factor behaviors in the tube fitted with the short helical tapes (SHTs) acting as decaying swirl flow generators. The tapes with three different helical tape angles (? = 90°, 135° and 180°) and three different channel numbers (N = 2, 3 and 4 channels) were tested under the uniform wall heat flux condition. The performance of each tape is compared with the performance of the plain tube subject to the same pumping power. The experimental results show that the heat transfer rates and friction factors of the tube with SHTs are respectively in range of 1.15 to 1.9 and 1.49 to 2.31 times of those in the plain, corresponding to thermal performances between 0.98 and 1.46. The correlations for Nusselt number (Nu) as a function of Reynolds number (Re), Prandtl number (Pr), helical tape angle (?) and the number of channel (N) are also developed.

Analytical Prediction of Heat Transfer in Tape Generated Swirl Flow

2017 ◽  
Author(s):  
R. J. Yadav ◽  
Sandeep Kore ◽  
V. N. Riabhole
Keyword(s):  
Heat Transfer ◽  
Circular Tube ◽  
Swirl Flow ◽  
Twisted Tape ◽  
Analytical Prediction ◽  
Transfer Coefficients ◽  
Numerical Predictions ◽  
Twisted Tapes ◽  
Wide Range ◽  
Prandtl Numbers

Heat transfer and pressure drop characteristics in a circular tube with twisted tapes have been investigated experimentally and numerically using different working fluids by many researchers for wide range of Reynolds number. The swirl was generated by tape inserts of various twist ratios. The various twist ratios are considered Many researchers formed generalized correlations to predict friction factors and convective heat transfer coefficients with twisted tapes in a tube for a wide range of Reynolds numbers and Prandtl numbers. Satisfactory agreement was obtained between the present correlations and the data of others validate the proposed correlations. The experimental or numerical predictions were compared with earlier correlations revealing good agreement between them. From the literature review it is observed that most studies are mainly focused on the heat transfer enhancement using twisted tape by experimental or numerical solution. An investigation with analytical approach is rarely reported. Therefore, the main aim of the present work is to form a correlation from theoretical approach for Nusselt number for circular tube with twisted tape. Application of dimensional analysis to heat transfer in tape generated swirl flow is carried out.

scholarly journals Effect of Conical Strip Inserts and ZrO2/DI-Water Nanofluid on Heat Transfer Augmentation: An Experimental Study

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4554
Author(s):  
Mohamed Iqbal Shajahan ◽  
Jee Joe Michael ◽  
M. Arulprakasajothi ◽  
Sivan Suresh ◽  
Emad Abouel Nasr ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Test Section ◽  
Volume Concentration ◽  
Swirl Flow ◽  
Performance Ratio ◽  
Transfer Rates ◽  
Heat Transfer Augmentation ◽  
Twist Ratio ◽  
Constant Wall Heat Flux

There is a significant enhancement of the heat transfer rate with the usage of nanofluid. This article describes a study of the combination of using nanofluid with inserts, which has proved itself in attaining higher benefits in a heat exchanger, such as the radiator in automobiles, industries, etc. Nanofluids are emerging as alternative fluids for heat transfer applications due to enhanced thermal properties. In this paper, the thermal hydraulic performance of ZrO2, awater-based nanofluid with various volume concentrations of 0.1%, 0.25%, and 0.5%, and staggered conical strip inserts with three different twist ratios of 2.5, 3.5, and 4.5 in forward and backward flow patterns were experimentally tested under a fully developed laminar flow regime of 0–50 lphthrough a horizontal test pipe section with a length of 1 m with a constant wall heat flux of 280 W as the input boundary condition. The temperatures at equidistant position and across the test section were measured using K-type thermocouples. The pressure drop across the test section was measured using a U-tube manometer. The observed results showed that the use of staggered conical strip inserts improved the heat transfer rates up to that of 130.5%, 102.7%, and 64.52% in the forward arrangement, and similarly 145.03%, 116.57%, and 80.92% in the backward arrangement with the twist ratios of 2.5, 3.5, and 4.5 at the 0.5% volume concentration of ZrO2 nanofluid. It was also seen that the improvement in heat transfer was comparatively lower for the other two volume concentrations considered in this study. The twist ratio generates more swirl flow, disrupting the thermal hydraulic boundary layer. Nanofluids with a higher volume concentration lead to higher heat transfer due to higher effective thermal conductivity of the prepared nanofluid. The thermal performance factor (TPF) with conical strip inserts at all volume concentrations of nanofluids was perceived as greater than 1. A sizable thermal performance ratio of 1.62 was obtained for the backward-arranged conical strip insert with 2.5 as the twist ratio and a volume concentration of 0.5% ZrO2/deionized water nanofluid. Correlations were developed for the Nusselt number and friction factor based on the obtained experimental data with the help of regression analysis.

scholarly journals Heat Transfer Enhancement by Detached S-Ribs for Twin-Pass Parallelogram Channel

Inventions ◽  
2018 ◽  
Vol 3 (3) ◽  
pp. 50 ◽  
Author(s):  
Shyy Chang ◽  
Wei-Ling Cai ◽  
Ruei-Jhe Wu
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Reynolds Numbers ◽  
Test Channel ◽  
Pressure Drops ◽  
Transfer Rates ◽  
Performance Factors ◽  
Nusselt Numbers ◽  
Friction Factors ◽  
Measured Pressure

Detached S-ribs are proposed to arrange in the stagger manner along two parallelogram straight channels interconnecting with a 180° smooth-walled sharp bend for heat transfer enhancements. The detailed Nusselt number distributions over the two opposite channel endwalls at Reynolds numbers of 5000, 7500, 10,000, 12,500, 15,000 and 20,000 are measured using the steady-state infrared thermography method. The accompanying Fanning friction factors are evaluated from the measured pressure drops across the entire test channel. Having acquired the averaged heat transfer properties and Fanning friction factors, the thermal performance factors are determined under the criterion of constant pumping power consumptions. With the regional accelerated flows between the detached S-ribs and the channel endwall, the considerable heat transfer elevations from the Dittus–Boelter correlation levels are achieved. The comparative thermal performances between the two similar twin-pass parallelogram channels with detached 90° and S-ribs disclose the higher regional heat transfer rates over the turning region and the larger Fanning frictions factors, leading to the lower thermal performance factors, for present test channel with the detached S-ribs. To assist design applications, two sets of empirical correlations evaluating the regionally averaged Nusselt numbers and Fanning friction factors are devised for present twin-pass parallelogram channel with the detached S-ribs.

Prediction of Swirl Flow and Heat Transfer through Square Duct with Twisted Tape Insert

2013 ◽  
Vol 284-287 ◽  
pp. 888-893 ◽  
Author(s):  
Ho Keun Kang ◽  
Soo Whan Ahn ◽  
Myung Sung Lee
Keyword(s):  
Heat Transfer ◽  
Turbulent Flows ◽  
Flow Direction ◽  
Swirl Flow ◽  
Hydraulic Diameter ◽  
Twisted Tape ◽  
Square Duct ◽  
Square Channel ◽  
Numerical Predictions ◽  
Commercial Code

Numerical predictions of characteristics of turbulent flows through a square duct (30 30 mm) with twisted tape inserts and with twisted tape inserts plus interrupted ribs are conducted to investigate regionally averaged heat transfer and friction factors by using CFX 11.0 commercial code. The validity of the numerical results is confirmed by measurement. Reynolds numbers are varied between 8,900 and 29,000. A rib height-to-channel hydraulic diameter (e/Dh) of 0.067 and a length-to hydraulic diameter (L/Dh) of 30 are considered. The square ribs are arranged to follow the trace of the twisted tape and along the flow direction defined as axial interrupted ribs. The twisted tape is 0.1 mm thick carbon steel sheet with diameter of 28mm, length of 900mm and 2.5 turns. Each wall of the square channel is composed of the isolated aluminum section. The present study demonstrates that the twisted tape with interrupted ribs provides a greater overall heat transfer performance over the twisted tape with no ribs in the square duct.

Heat Transfer and Pressure Drop Correlations for Twisted-Tape Inserts in Isothermal Tubes: Part I—Laminar Flows

1993 ◽  
Vol 115 (4) ◽  
pp. 881-889 ◽  
Author(s):  
R. M. Manglik ◽  
A. E. Bergles
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Swirl Flow ◽  
Laminar Flows ◽  
Low Flow ◽  
Published Data ◽  
Twisted Tape ◽  
Flow Rates ◽  
Uniform Wall Temperature ◽  
Uniform Wall

Laminar flow correlations for f and Num are developed based on experimental data for water and ethylene glycol, with tape inserts of three different twist ratios. The uniform wall temperature condition is considered, which typifies practical heat exchangers in the chemical and process industry. These and other available data are analyzed to devise flow regime maps that characterize twisted-tape effects in terms of the dominant enhancement mechanisms. Depending upon flow rates and tape geometry, the enhancement in heat transfer is due to the tube partitioning and flow blockage, longer flow path, and secondary fluid circulation; fin effects are found to be negligible in snug- to loose-fitting tapes. The onset of swirl flow and its intensity is determined by a swirl parameter, Sw=Resw/y, that defines the interaction between viscous, convective inertia, and centrifugal forces. Buoyancy-driven free convection that comes into play at low flow rates with large y and ΔTw is shown to scale as Gr/Sw2≫ 1. These parameters, along with numerical baseline solutions for laminar flows with y = ∞, are incorporated into correlations for f and Num by matching the appropriate asymptotic behavior. The correlations describe the experimental data within ±10 to 15 percent, and their generalized applicability is verified by the comparison of predictions with previously published data.

Modeling of Interfacial Shear for Gas Liquid Flows in Annular Film Condensation

1996 ◽  
Vol 63 (2) ◽  
pp. 529-538 ◽  
Author(s):  
A. Narain
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Internal Flow ◽  
Admissible Solution ◽  
Interfacial Shear ◽  
Film Condensation ◽  
Vapor Flow ◽  
Pressure Drops ◽  
Transfer Rates ◽  
Stability Type

Internal flow of pure vapor experiencing film condensation on the walls of a straight horizontal duct is studied. The commonly occurring annular case of turbulent (or laminar) vapor flow in the core and laminar flow of the liquid condensate—with or without waves on the interface—is emphasized. We present a new methodology which models interfacial shear with the help of theory, computations, and reliable experimental data on heat transfer rates. The theory—at the point of onset of condensation—deals with issues of asymptotic form of interfacial shear, nonuniqueness of solutions, and selection of the physically admissible solution by a stability type criteria. Other details of the flow are predicted with the help of the proposed modeling approach. These predictions are shown to be in agreement with relevant experimental data. The trends for film thickness, heat transfer rates, and pressure drops are also made available in the form of power-law correlations.

Thermohydraulic Study of Laminar Swirl Flow Through a Circular Tube Fitted With Twisted Tapes

2001 ◽  
Vol 123 (3) ◽  
pp. 417-427 ◽  
Author(s):  
S. K. Saha ◽  
A. Dutta
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Prandtl Number ◽  
Friction Factor ◽  
Circular Tube ◽  
Swirl Flow ◽  
Short Length ◽  
Full Length ◽  
Twisted Tape ◽  
Twisted Tapes

Heat transfer and pressure drop characteristics in a circular tube fitted with twisted tapes have been investigated experimentally. Laminar swirl flow of a large Prandtl number 205<Pr<518 viscous fluid was considered. The swirl was generated by short-length twisted-tape inserts; regularly spaced twisted-tape elements with multiple twists in the tape module and connected by thin circular rods; and smoothly varying (gradually decreasing) pitch twisted-tapes. The heat transfer test section was heated electrically imposing axially and circumferentially constant wall heat flux (UHF) boundary condition. Reynolds number, Prandtl number, twist ratio, space ratio, number of tuns in the tape module, length of the twisted-tape and smoothness of the swirling pitch govern the characteristics. Friction factor and Nusselt number are lower for short-length twisted-tape than those for full-length twisted-tape. On the basis of constant pumping power and constant heat duty, however, short-length twisted-tapes are found to perform better than full-length twisted-tapes for tighter twists. Thermohydraulic performance shows that twisted-tapes with multiple twists in the tape module is not much different from that with single twist in the tape module. Friction factor and Nusselt number are approximately 15 percent lower for twisted-tapes with smooth swirl having the average pitch same as that of the uniform pitch (throughout) twisted-tape and the twisted-tapes with gradually decreasing pitch perform worse than their uniform-pitch counterparts.

R-22 and Zeotropic R-22/R-142b Mixture Condensation in Microfin, High-Fin, and Twisted Tape Insert Tubes

2002 ◽  
Vol 124 (5) ◽  
pp. 912-921 ◽  
Author(s):  
F. J. Smit ◽  
J. P. Meyer
Keyword(s):  
Heat Transfer ◽  
Saturation Temperature ◽  
Twisted Tape ◽  
Outer Diameter ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Mass Fluxes ◽  
Smooth Tubes ◽  
Enhancement Method

Using mixtures of the zeotropic refrigerant mixture R-22/R-142b, a series of experiments was performed to determine the sectional and average heat transfer coefficients. Experiments were also conducted to compare three different heat transfer enhancement methods to that of smooth tubes. They were microfins, twisted tapes, and high fins. Measurements at different mass fluxes were obtained at six refrigerant mass fractions from 100 percent R-22 up to a 50 percent/50 percent mixture of R-22/R-142b. All condensation measurements were conducted at an isobaric inlet pressure of 2.43 MPa. This pressure corresponds to a saturation temperature of 60°C for R-22. The measurements were taken in 9.53 mm outer diameter smooth tubes and microfin tubes with lengths of 1603 mm. The heat transfer coefficients were determined with the Log Mean Temperature Difference equations. It was found that microfins were more suitable as an enhancement method than twisted tubes or high fins. Also, that the heat transfer coefficients and pressure drops decrease as the mass fraction of R-142b increases.

Sign in / Sign up

Export Citation Format

Share Document