An Experimental Study of Natural Convection in an Inclined Rectangular Cavity Filled With Water at Its Density Extremum

1984 ◽  
Vol 106 (1) ◽  
pp. 109-115 ◽  
Author(s):  
H. Inaba ◽  
T. Fukuda
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Water Layer ◽  
Flow Patterns ◽  
Maximum Density ◽  
Rectangular Cavity ◽  
Density Inversion ◽  
Different Temperatures ◽  
Inclination Angles

An experimental investigation pertaining to the effect of the density inversion of water on steady natural convective flow patterns and heat transfer in an inclined rectangular cavity whose two opposing walls are kept at different temperatures is carried out. Water as a testing fluid has its maximum density at about 4 °C. The temperature of one wall is maintained at 0 °C, while that of the opposing hot wall is varied from 2 to 20 °C. Photographs of the flow patterns, temperature distribution in the water layer, and average Nusselt number are presented under various hot wall temperatures and inclination angles of the cavity. The present results could indicate that the density inversion of water has an influential effect on the natural convective heat transfer in the prescribed water layer. Moreover, the average Nusselt number is a peculiar function of the temperature difference between the cold and hot walls and inclination angle, unlike the previous results for common fluids without density inversion.

Localized Heat Transfer in Buoyancy Driven Convection in Open Cavities

2006 ◽  
Vol 129 (2) ◽  
pp. 167-178 ◽  
Author(s):  
Wilson Terrell ◽  
Ty A. Newell
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Ambient Air ◽  
Nusselt Numbers ◽  
Transient Nature ◽  
Inclination Angles ◽  
Buoyancy Driven Convection ◽  
The Heat Transfer Coefficient

Background. An experimental study of buoyancy driven convection heat transfer in an open cavity was conducted. Method of Approach. Test cavities were constructed with calorimeter plates bonded to Styrofoam insulation. The inside of the cavities was heated and then exposed to ambient air for approximately thirty minutes. Different size cavities were examined at inclination angles of 0, 45, and 90deg. The heat transfer coefficient was determined from an energy balance on each calorimeter plate. The cavity’s plate temperatures varied spatially due to the transient nature of the tests. A parameter describing the nonisothermal cavity wall temperature variation was defined in order to compare with isothermal cavity heat transfer results. Results. Results showed that the cavity Nusselt number, based on a cavity averaged temperature, was insensitive to the transient development of nonisothermal conditions within the cavity. Comparison of cavity-average Nusselt number for the current study, where the Rayleigh number ranged from 5×106 to 2×108, to data from the literature showed good agreement. Cavity-average Nusselt number relations for inclination angles of 0, 45, and 90deg in the form of NuH,cav=CRa1∕3 resulted in coefficients of 0.091, 0.105, 0.093, respectively. The 45deg inclination angle orientation yielded the largest Nusselt numbers, which was similar to previous literature results. Trends in the local plate Nusselt numbers were examined and found similar to data from the literature.

scholarly journals Effect of Various Tilted Positions of a Thin Fin on Natural Convection of Laminar Viscous Flow in a Square Cavity

2021 ◽  
Vol 39 (5) ◽  
pp. 1634-1642
Author(s):  
Syed Fazuruddin ◽  
Seelam Sreekanth ◽  
G Sankara Sekhar Raju
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Finite Difference ◽  
Average Nusselt Number ◽  
Vertical Position ◽  
Inclination Angles ◽  
Rayleigh Numbers

An exhaustive numerical investigation is carried out to analyze the role of an isothermal heated thin fin on fluid flow and temperature distribution visualization in an enclosure. Natural convection within square enclosures finds remarkable pragmatic applications. In the present study, a finite difference approach is performed on two-dimensional laminar flow inside an enclosure with cold side walls and adiabatic horizontal walls. The fluid flow equations are reconstructed into vorticity - stream function formulation and these equations are employed utilizing the finite-difference strategy with incremental time steps. The parametric study includes a wide scope of Rayleigh number, Ra, and inclination angle ϴ of the thin fin. The effect of different Rayleigh numbers ranging Ra = 104-106 with Pr=0.71 for all the inclination angles from 0°-360° with uniform rotational length of angle 450 of an inclined heated fin on fluid flow and heat transfer have been investigated. The heat transfer rate within the enclosure is measured by means of local and average Nusselt numbers. Regardless of inclination angles of the thin fin, a slight enhancement in the average Nusselt number is observed when Rayleigh number increased for both the cases of the horizontal and vertical position of the thin fin. When the fin has inclined no change in average Nusselt number is noticed for distinct Rayleigh numbers.

Experimental Study on Natural Convection Heat Transfer With Density Inversion of Water Between Two Horizontal Concentric Cylinders

1975 ◽  
Vol 97 (4) ◽  
pp. 556-561 ◽  
Author(s):  
N. Seki ◽  
S. Fukusako ◽  
M. Nakaoka
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Nusselt Number ◽  
Natural Convection ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Density Inversion ◽  
Concentric Cylinders

An experimental investigation concerning the effect of density inversion on steady natural convection heat transfer of water between two horizontal concentric cylinders with diameter ratio ranging from 1.18 to 6.39 is carried out. Water, as a testing fluid, has the maximum density at 4°C. Temperature of the inner cylinder is maintained at 0°C, while temperatures of the outer cylinder are varied from 1 to 15°C, with Grashof number ranging from 3.2 × 101 to 2.7 × 105. Photographs and qualitative description of the flow patterns, temperature profiles, local and average Nusselt number are presented. From the present experimental investigation, it is demonstrated that the effect of density inversion is unexpectedly large and the average Nusselt number is a peculiar function of temperature difference between outer and inner cylinder, unlike the previous results on common fluids without density inversion.

Natural convection in an inclined square cavity in regions of density inversion of water

1984 ◽  
Vol 142 ◽  
pp. 363-381 ◽  
Author(s):  
Hideo Inaba ◽  
Takeyuki Fukuda
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Water Layer ◽  
Density Inversion ◽  
Transfer Coefficients ◽  
Square Cavity ◽  
Average Heat ◽  
Heat Transfer Coefficients ◽  
Inclination Angles ◽  
Laminar Natural Convection

The steady laminar natural convection of water in an inclined square cavity is investigated experimentally and analytically at temperatures in the neighbourhood of maximum density near 4°C. One hot wall of the square cavity is maintained at various uniform temperatures from 2 to 20°C and the opposing cold wall is kept at a uniform temperature of 0°C, while the other walls are thermally insulated. Photographs and analytical descriptions of the flow patterns, temperature profiles in the water layer and average heat-transfer coefficients are presented in this paper for various surface temperatures Th of the hot wall and inclination angles of the square cavity θ from 0° (heated from below) to 180° (heated from above) by 30° intervals. From this study it should be noted that the density inversion of water has a strong effect on the natural convection occurring in the inclined square cavity, and the average heat-transfer coefficient is a peculiar function of the surface temperature of the hot wall, unlike previous results for Boussinesq fluids without density inversion. Solutions of the governing equations for steady two-dimensional laminar natural convection are obtained numerically, and the results obtained agree reasonably well with the experimental ones in the ranges of 30° < θ ≤ 180° for Th > 8°C, 0° ≤ θ ≤ 120° for Th < 8°C, and 0° ≤ θ ≤ 180° for Th = 8°C.

Influence of Partition Length on Natural Convection in Partially Divided Square Enclosure

2007 ◽  
Vol 129 (11) ◽  
pp. 1592-1599 ◽  
Author(s):  
C. D. Sankhavara ◽  
H. J. Shukla
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Average Nusselt Number ◽  
Square Enclosure ◽  
Thermal Boundary Conditions ◽  
Different Temperatures ◽  
Vertical Walls ◽  
Good Agreement

Numerical investigation is carried out for natural convection in square enclosures consisting of partitions protruding from the end walls with different thermal boundary conditions at the end walls and partitions. The vertical walls were maintained isothermal at different temperatures. The Rayleigh number varies from 104 to 106 and the Prandtl number is 0.71. The thickness of the partition is fixed and is equal to one-tenth of the width of the enclosure. Their nondimensional length (l∕H) varies from 0 (a nonpartitioned enclosure) to 0.5 (two separate enclosures). A good agreement was found between the results in the present study and those published previously. The partitions were found to significantly influence the convective heat transfer. The average Nusselt number is less in the presence of partitions, and it decreases with increasing partition length (l∕H) from 0 to 0.5.

Forced convection heat transfer study of a blunt-headed cylinder in non-Newtonian power-law fluids

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Jaspinder Kaur ◽  
Roderick Melnik ◽  
Anurag Kumar Tiwari
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Drag Coefficient ◽  
Power Law ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Convection Heat ◽  
Total Drag ◽  
Shear Thinning Fluids ◽  
Power Law Fluids

Abstract In this present work, forced convection heat transfer from a heated blunt-headed cylinder in power-law fluids has been investigated numerically over the range of parameters, namely, Reynolds number (Re): 1–40, Prandtl number (Pr): 10–100 and power-law index (n): 0.3–1.8. The results are expressed in terms of local parameters, like streamline, isotherm, pressure coefficient, and local Nusselt number and global parameters, like wake length, drag coefficient, and average Nusselt number. The length of the recirculation zone on the rear side of the cylinder increases with the increasing value of Re and n. The effect of the total drag coefficient acting on the cylinder is seen to be higher at the low value of Re and its effect significant in shear-thinning fluids (n < 1). On the heat transfer aspect, the rate of heat transfer in fluids is increased by increasing the value of Re and Pr. The effect of heat transfer is enhanced in shear-thinning fluids up to ∼ 40% and it impedes it’s to ∼20% shear-thickening fluids. In the end, the numerical results of the total drag coefficient and average Nusselt number (in terms of J H −factor) have been correlated by simple expression to estimate the intermediate value for the new application.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

Investigating the effect of nanoparticles diameter on turbulent flow and heat transfer properties of non-Newtonian carboxymethyl cellulose/CuO fluid in a microtube

2019 ◽  
Vol 29 (5) ◽  
pp. 1699-1723 ◽  
Author(s):  
Ali Rahimi Gheynani ◽  
Omid Ali Akbari ◽  
Majid Zarringhalam ◽  
Gholamreza Ahmadi Sheikh Shabani ◽  
Abdulwahab A. Alnaqi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Electronic Devices ◽  
Convection Heat Transfer ◽  
Reynolds Numbers ◽  
Vlsi Circuits ◽  
Convection Heat Transfer Coefficient ◽  
Content Type ◽  
Competing Interests

Purpose Although many studies have been conducted on the nanofluid flow in microtubes, this paper, for the first time, aims to investigate the effects of nanoparticle diameter and concentration on the velocity and temperature fields of turbulent non-Newtonian Carboxymethylcellulose (CMC)/copper oxide (CuO) nanofluid in a three-dimensional microtube. Modeling has been done using low- and high-Reynolds turbulent models. CMC/CuO was modeled using power law non-Newtonian model. The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices. Design/methodology/approach Present numerical simulation was performed with finite volume method. For obtaining higher accuracy in the numerical solving procedure, second-order upwind discretization and SIMPLEC algorithm were used. For all Reynolds numbers and volume fractions, a maximum residual of 10−6 is considered for saving computer memory usage and the time for the numerical solving procedure. Findings In constant Reynolds number and by decreasing the diameter of nanoparticles, the convection heat transfer coefficient increases. In Reynolds numbers of 2,500, 4,500 and 6,000, using nanoparticles with the diameter of 25 nm compared with 50 nm causes 0.34 per cent enhancement of convection heat transfer coefficient and Nusselt number. Also, in Reynolds number of 2,500, by increasing the concentration of nanoparticles with the diameter of 25 nm from 0.5 to 1 per cent, the average Nusselt number increases by almost 0.1 per cent. Similarly, In Reynolds numbers of 4,500 and 6,000, the average Nusselt number increases by 1.8 per cent. Research limitations/implications The numerical simulation was carried out for three nanoparticle diameters of 25, 50 and 100 nm with three Reynolds numbers of 2,500, 4,500 and 6,000. Constant heat flux is on the channel, and the inlet fluid becomes heated and exists from it. Practical implications The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices. Originality/value This manuscript is an original work, has not been published and is not under consideration for publication elsewhere. About the competing interests, the authors declare that they have no competing interests.

Heat Transfer and Flow Friction Characteristics for Compact Cold Plates

2003 ◽  
Vol 125 (1) ◽  
pp. 104-113 ◽  
Author(s):  
Chang-Yuan Liu ◽  
Ying-Huei Hung
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Nusselt Number ◽  
Thermal Resistance ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Average Nusselt Number ◽  
Cold Plate ◽  
Air Mass

Both experimental and theoretical investigations on the heat transfer and flow friction characteristics of compact cold plates have been performed. From the results, the local and average temperature rises on the cold plate surface increase with increasing chip heat flux or decreasing air mass flow rate. Besides, the effect of chip heat flux on the thermal resistance of cold plate is insignificant; while the thermal resistance of cold plate decreases with increasing air mass flow rate. Three empirical correlations of thermal resistance in terms of air mass flow rate with a power of −0.228 are presented. As for average Nusselt number, the effect of chip heat flux on the average Nusselt number is insignificant; while the average Nusselt number of the cold plate increases with increasing Reynolds number. An empirical relationship between Nu¯cp and Re can be correlated. In the flow frictional aspect, the overall pressure drop of the cold plate increases with increasing air mass flow rate; while it is insignificantly affected by chip heat flux. An empirical correlation of the overall pressure drop in terms of air mass flow rate with a power of 1.265 is presented. Finally, both heat transfer performance factor “j” and pumping power factor “f” decrease with increasing Reynolds number in a power of 0.805; while they are independent of chip heat flux. The Colburn analogy can be adequately employed in the study.

Sign in / Sign up

Export Citation Format

Share Document