Heat Transfer Coefficients and Patterns of Fluid Flow for Contacting Spheres at Various Angles of Attack

1983 ◽  
Vol 105 (1) ◽  
pp. 48-55 ◽  
Author(s):  
E. M. Sparrow ◽  
R. F. Prieto
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Separated Flow ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Features ◽  
Baseline Information ◽  
Single Sphere ◽  
Parameter Ranges

Wind tunnel experiments were performed to determine heat transfer coefficients and fluid flow patterns for two contacting spheres. The experiments were carried out at three different angles of attack and for Reynolds numbers in the range from 4000 to 26,000. Three heat transfer conditions were considered: (a) both spheres thermally active, (b) forwardmost sphere thermally active and rearmost sphere adiabatic, and (c) forwardmost sphere adiabatic and rearmost sphere thermally active. Complementary experiments for a single sphere, encompassing the same parameter ranges, yielded baseline information for comparison with the two-sphere results. It was found that the largest effects of the sphere-to-sphere interaction on the heat transfer occurred when the two spheres were in line. At this orientation and for higher Reynolds numbers in the investigated range, there was substantial enhancement of the heat transfer with respect to that for the single sphere. At the other angles of attack, there was lesser enhancement. The visualization studies revealed such key fluid flow features as the reattachment of the separated flow from the first sphere on the second, the presence of strong recirculations, and the delay of separation due to pressure-driven transverse flows.

A Numerical and Experimental Investigation of Turbulent Heat Transport Downstream From an Abrupt Pipe Expansion

1983 ◽  
Vol 105 (4) ◽  
pp. 862-869 ◽  
Author(s):  
R. S. Amano ◽  
M. K. Jensen ◽  
P. Goel
Keyword(s):  
Heat Transfer ◽  
Numerical Solutions ◽  
Numerical Study ◽  
Separated Flow ◽  
Flow Region ◽  
Reynolds Numbers ◽  
Turbulent Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Pipe Expansion

An experimental and numerical study is reported on heat transfer in the separated flow region created by an abrupt circular pipe expansion. Heat transfer coefficients were measured along the pipe wall downstream from an expansion for three different expansion ratios of d/D = 0.195, 0.391, and 0.586 for Reynolds numbers ranging from 104 to 1.5 × 105. The results are compared with the numerical solutions obtained with the k ∼ ε turbulence model. In this computation a new finite difference scheme is developed which shows several advantages over the ordinary hybrid scheme. The study also covers the derivation of a new wall function model. Generally good agreement between the measured and the computed results is shown.

Heat Transfer from a Plate Elevated above a Host Surface and Washed by a Separated Flow Induced by the Elevation Step

1981 ◽  
Vol 103 (3) ◽  
pp. 441-447 ◽  
Author(s):  
E. M. Sparrow ◽  
F. Samie ◽  
S. C. Lau
Keyword(s):  
Heat Transfer ◽  
Flow Separation ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Active Surface ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Reynolds Number Flow ◽  
Heat Transfer Coefficients ◽  
High Reynolds

Wind tunnel experiments were performed to determine heat transfer coefficients and fluid flow patterns for a thermally active surface elevated above a parallel host surface. The step-like blockage associated with the elevation causes flow separation and recirculation on the forward portion of the thermally active surface. Four parameters were varied during the course of the experiments, including the angle of attack of the oncoming airflow relative to the surface, the step height, the extent of the host surface which frames the active surface (i.e., the skirt width), and the Reynolds number. Flow visualization studies, performed with the oil-lampblack technique, showed that the streamwise extent of the separation zone increases with decreasing angle of attack, with larger step heights and skirt widths, and at higher Reynolds numbers. At larger angles of attack, separation does not occur. The experimentally determined heat transfer coefficients were found to increase markedly due to the flow separation, and separation-related enhancements as large as a factor of two were encountered. The enhancement was accentuated at small angles of attack, at large step heights and skirt widths, and at high Reynolds numbers. A main finding of the study is that the separation-affected heat transfer coefficients are generally greater than those for no separation, so that the use of the latter may underestimate the heat transfer rates. For an application such as a retrofit solar collector, such an underestimation of the wind-related heat loss would yield an optimistic prediction of the collector efficiency.

Heat Transfer in a Surfactant Drag-Reducing Solution—A Comparison With Predictions for Laminar Flow

2005 ◽  
Vol 128 (6) ◽  
pp. 557-563 ◽  
Author(s):  
Paul L. Sears ◽  
Libing Yang
Keyword(s):  
Heat Transfer ◽  
Laminar Flow ◽  
Reynolds Numbers ◽  
High Heat ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Drag Reducing Additive ◽  
Good Agreement

Heat transfer coefficients were measured for a solution of surfactant drag-reducing additive in the entrance region of a uniformly heated horizontal cylindrical pipe with Reynolds numbers from 25,000 to 140,000 and temperatures from 30to70°C. In the absence of circumferential buoyancy effects, the measured Nusselt numbers were found to be in good agreement with theoretical results for laminar flow. Buoyancy effects, manifested as substantially higher Nusselt numbers, were seen in experiments carried out at high heat flux.

Heat Transfer and Pressure Drop Correlations for Square Channels With 45 Deg Ribs at High Reynolds Numbers

2009 ◽  
Vol 131 (7) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Huitao Yang ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Turbine Blade Cooling ◽  
Square Channel ◽  
Heat Transfer Coefficients ◽  
High Reynolds ◽  
Cooling Passage

Systematic experiments are conducted to measure heat transfer enhancement and pressure loss characteristics on a square channel (simulating a gas turbine blade cooling passage) with two opposite surfaces roughened by 45 deg parallel ribs. Copper plates fitted with a silicone heater and instrumented with thermocouples are used to measure regionally averaged local heat transfer coefficients. Reynolds numbers studied in the channel range from 30,000 to 400,000. The rib height (e) to hydraulic diameter (D) ratio ranges from 0.1 to 0.18. The rib spacing (p) to height ratio (p/e) ranges from 5 to 10. Results show higher heat transfer coefficients at smaller values of p/e and larger values of e/D, though at the cost of higher friction losses. Results also indicate that the thermal performance of the ribbed channel falls with increasing Reynolds numbers. Correlations predicting Nusselt number (Nu) and friction factor (f¯) as a function of p/e, e/D, and Re are developed. Also developed are correlations for R and G (friction and heat transfer roughness functions, respectively) as a function of the roughness Reynolds number (e+), p/e, and e/D.

Heat Transfer and Friction in Channels With Very High Blockage 45° Staggered Turbulators

2003 ◽  
Author(s):  
Jeremy C. Bailey ◽  
Ronald S. Bunker
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Flow Area ◽  
Test Technique ◽  
Heat Transfer Coefficients ◽  
Smooth Channel ◽  
Constant Pitch ◽  
Transfer Behavior ◽  
Very High

Heat transfer and friction coefficients have been measured within a rectangular passage of aspect ratio 0.4 containing 45-degree staggered turbulators of very high blockage. Using a constant pitch-to-height ratio of 10 for all geometries, turbulator height-to-channel hydraulic diameter ratios from 0.193 to 0.333 were investigated. This range of e/D creates actual channel blockage ratios e/H from 0.275 to 0.475, presenting significant flow area restrictions. A liquid crystal test technique is used to obtain both detailed heat transfer behavior on the surfaces between turbulators, as well as averaged fully developed heat transfer coefficients. Reynolds numbers from 20000 to 100000 were tested. Nusselt number enhancements of up to 3.6 were obtained over that of a smooth channel, with friction coefficient enhancements of as much as 65. In contrast to low-blockage turbulated channels, the 45-degree turbulated Nu is found to be lower than that at 90-degree orientation, given very similar e/D and e/H values.

Heat Transfer in Rotating Serpentine Coolant Passage With Ribbed Walls at Low Mach Numbers

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Salam Azad ◽  
Ching-Pang Lee
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Low Mach Number ◽  
Heat Transfer Coefficients ◽  
Rotation Numbers ◽  
Wide Range ◽  
Mach Numbers

This paper experimentally investigates the effect of rotation on heat transfer in typical turbine blade serpentine coolant passage with ribbed walls at low Mach numbers. To achieve the low Mach number (around 0.01) condition, pressurized Freon R-134a vapor is utilized as the working fluid. The flow in the first passage is radial outward, after the 180 deg tip turn the flow is radial inward to the second passage, and after the 180 deg hub turn the flow is radial outward to the third passage. The effects of rotation on the heat transfer coefficients were investigated at rotation numbers up to 0.6 and Reynolds numbers from 30,000 to 70,000. Heat transfer coefficients were measured using the thermocouples-copper-plate-heater regional average method. Heat transfer results are obtained over a wide range of Reynolds numbers and rotation numbers. An increase in heat transfer rates due to rotation is observed in radially outward passes; a reduction in heat transfer rate is observed in the radially inward pass. Regional heat transfer coefficients are correlated with Reynolds numbers for nonrotation and with rotation numbers for rotating condition, respectively. The results can be useful for understanding real rotor blade coolant passage heat transfer under low Mach number, medium–high Reynolds number, and high rotation number conditions.

Experimental Investigation of Local Heat Transfer Distribution on Smooth and Roughened Surfaces Under an Array of Angled Impinging Jets

2001 ◽  
Author(s):  
Lamyaa A. El-Gabry ◽  
Deborah A. Kaminski
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Cross Flow ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Impinging Jets ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Roughened Surface

Abstract Measurements of the local heat transfer distribution on smooth and roughened surfaces under an array of angled impinging jets are presented. The test rig is designed to simulate impingement with cross-flow in one direction which is a common method for cooling gas turbine components such as the combustion liner. Jet angle is varied between 30, 60, and 90 degrees as measured from the impingement surface, which is either smooth or randomly roughened. Liquid crystal video thermography is used to capture surface temperature data at five different jet Reynolds numbers ranging between 15,000 and 35,000. The effect of jet angle, Reynolds number, gap, and surface roughness on heat transfer efficiency and pressure loss is determined along with the various interactions among these parameters. Peak heat transfer coefficients for the range of Reynolds number from 15,000 to 35,000 are highest for orthogonal jets impinging on roughened surface; peak Nu values for this configuration ranged from 88 to 165 depending on Reynolds number. The ratio of peak to average Nu is lowest for 30-degree jets impinging on roughened surfaces. It is often desirable to minimize this ratio in order to decrease thermal gradients, which could lead to thermal fatigue. High thermal stress can significantly reduce the useful life of engineering components and machinery. Peak heat transfer coefficients decay in the cross-flow direction by close to 24% over a dimensionless length of 20. The decrease of spanwise average Nu in the crossflow direction is lowest for the case of 30-degree jets impinging on a roughened surface where the decrease was less than 3%. The decrease is greatest for 30-degree jet impingement on a smooth surface where the stagnation point Nu decreased by more than 23% for some Reynolds numbers.

Periodically Converging-Diverging Tubes and Their Turbulent Heat Transfer, Pressure Drop, Fluid Flow, and Enhancement Characteristics

1984 ◽  
Vol 106 (1) ◽  
pp. 55-63 ◽  
Author(s):  
P. Souza Mendes ◽  
E. M. Sparrow
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Surface Area ◽  
Equal Mass ◽  
Turbulent Heat Transfer ◽  
Turbulent Heat ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Friction Factors

A comprehensive experimental study was performed to determine entrance region and fully developed heat transfer coefficients, pressure distributions and friction factors, and patterns of fluid flow in periodically converging and diverging tubes. The investigated tubes consisted of a succession of alternately converging and diverging conical sections (i.e., modules) placed end to end. Systematic variations were made in the Reynolds number, the taper angle of the converging and diverging modules, and the module aspect ratio. Flow visualizations were performed using the oil-lampblack technique. A performance analysis comparing periodic tubes and conventional straight tubes was made using the experimentally determined heat transfer coefficients and friction factors as input. For equal mass flow rate and equal transfer surface area, there are large enhancements of the heat transfer coefficient for periodic tubes, with accompanying large pressure drops. For equal pumping power and equal transfer surface area, enhancements in the 30–60 percent range were encountered. These findings indicate that periodic converging-diverging tubes possess favorable enhancement characteristics.

scholarly journals Теплообмен при смешанной конвекции расплава соли в присутствии магнитных полей

2019 ◽  
Vol 45 (10) ◽  
pp. 27
Author(s):  
И.А. Беляев ◽  
Д.А. Бирюков ◽  
А.В. Котляр ◽  
Е.А. Белавина ◽  
П.А. Сардов ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Temperature Fluctuations ◽  
Reynolds Numbers ◽  
Transverse Magnetic ◽  
Statistical Characteristics ◽  
Transfer Coefficients ◽  
Gravitational Flow ◽  
Heat Transfer Coefficients ◽  
The Magnetic Field

The results of an experimental study of the salt melt downflow in a uniformly heated pipe under the influence of a strong transverse magnetic field are presented. The changes of heat transfer coefficients and statistical characteristics of temperature fluctuations under the influence of the magnetic field are investigated. The peculiarities of the transition of the viscous-gravitational flow in the viscous-inertial-gravitational flow at Reynolds numbers (Re=3000-5000) under the influence of the magnetic field (Ha=17) were studied.

scholarly journals Experimental Study of Forced Convective Heat Transfer in a Coiled Flow Inverter Using TiO2–Water Nanofluids

2020 ◽  
Vol 10 (15) ◽  
pp. 5225
Author(s):  
Barbara Arevalo-Torres ◽  
Jose L. Lopez-Salinas ◽  
Alejandro J. García-Cuéllar
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Convective Thermal ◽  
Convective Heat Transfer Coefficients

The curved geometry of a coiled flow inverter (CFI) promotes chaotic mixing through a combination of coils and bends. Besides the heat exchanger geometry, the heat transfer can be enhanced by improving the thermophysical properties of the working fluid. In this work, aqueous solutions of dispersed TiO2 nanometer-sized particles (i.e., nanofluids) were prepared and characterized, and their effects on heat transfer were experimentally investigated in a CFI heat exchanger inserted in a forced convective thermal loop. The physical and transport properties of the nanofluids were measured within the temperature and volume concentration domains. The convective heat transfer coefficients were obtained at Reynolds numbers (NRe) and TiO2 nanoparticle volume concentrations ranging from 1400 to 9500 and 0–1.5 v/v%, respectively. The Nusselt number (NNu) in the CFI containing 1.0 v/v% nanofluid was 41–52% higher than in the CFI containing pure base fluid (i.e., water), while the 1.5 v/v% nanofluid increased the NNu by 4–8% compared to water. Two new correlations to predict the NNu of TiO2–water nanofluids in the CFI at Reynolds numbers of 1400 ≤ NRe ≤ 9500 and nanoparticle volume concentrations ranges of 0.2–1.0 v/v% and 0.2–1.5 v/v% are proposed.

Sign in / Sign up

Export Citation Format

Share Document