Experimental Investigation of Electrostatic Dispersion and Combustion of Diesel Fuel Jets

1988 ◽  
Vol 110 (3) ◽  
pp. 361-368 ◽  
Author(s):  
C. P. Bankston ◽  
L. H. Back ◽  
E. Y. Kwack ◽  
A. J. Kelly
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Fluid Model ◽  
Operating Conditions ◽  
Injection Technique ◽  
Spray Characteristics ◽  
Model Calculations ◽  
Flow Rates ◽  
Charge Densities

An experimental study of electrostatically atomized and dispersed diesel fuel jets has been conducted. A new electrostatic injection technique has been utilized to generate continuous, stable fuel sprays at charge densities of 1.5–2.0 C/m3 of fluid. Model calculations show that such charge densities may enhance spray dispersion under diesel engine conditions. Fuel jets were injected into room temperature air at one atmosphere at flow rates of 0.25–1.0 cm3/s and delivery pressures of 100–400 kPa. Measured mean drop diameters were near 150 μm with 30 percent of the droplets being less than 100 μm in diameter at typical operating conditions. The electrical power required to generate these sprays was less than 10−6 times the chemical energy available from the fuel. The spray characteristics of an actual diesel engine injector were also studied. The results show considerable differences in spray characteristics between the diesel injector and electrostatic injection. Finally, ignition and stable combustion of electrostatically dispersed diesel fuel jets was achieved. The results show that electrostatic fuel injection can be achieved at practical flow rates, and that the characteristics of the jet breakup and dispersion have potential application to combustion systems.

scholarly journals A Study on Water-Induced Damage Severity on Diesel Engine Injection System Using Emulsified Diesel Fuels

Electronics ◽  
2021 ◽  
Vol 10 (18) ◽  
pp. 2285
Author(s):  
Min-Seop Kim ◽  
Ugochukwu Ejike Akpudo ◽  
Jang-Wook Hur
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Energy Demand ◽  
Fuel Injection ◽  
Nox Reduction ◽  
Cost Effective ◽  
Operating Conditions ◽  
Injection System ◽  
Diesel Fuels ◽  
Diesel Fuel Injection

Diesel engine emissions contribute nearly 30% of greenhouse effects and diverse health and environmental problems. Amidst these problems, it is estimated that there will be a 75% increase in energy demand for transportation by 2040, of which diesel fuel constitutes a major source of energy for transportation. Being a major source of air pollution, efforts are currently being made to curb the pollution spread. The use of water-in-diesel (W/D)-emulsified fuels comes as a readily available (and cost-effective) option with other benefits including engine thermal efficiency, reduced costs, and NOx reduction; nonetheless, the inherent effects—power loss, component wear, corrosion, etc. still pose strong concerns. This study investigates the behavior and damage severity of a common rail (CR) diesel fuel injection system using exploratory and statistical methods under different W/D emulsion conditions and engine speeds. Results reveal that the effect of W/D emulsion fuels on engine operating conditions are reflected in the CR, which provides a reliable avenue for condition monitoring. Also, the effect of W/D emulsion on injection system components-piston, nozzle needle, and ball seat–are presented alongside related discussions.

scholarly journals Compressed Biogas-Diesel Dual-Fuel Engine Optimization Study for Ultralow Emission

2014 ◽  
Vol 6 ◽  
pp. 571063 ◽  
Author(s):  
Hasan Koten ◽  
Mustafa Yilmaz ◽  
M. Zafer Gul
Keyword(s):  
Diesel Engine ◽  
Multiobjective Optimization ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Exhaust Emission ◽  
Dual Fuel ◽  
Optimization Study

The aim of this study is to find out the optimum operating conditions in a diesel engine fueled with compressed biogas (CBG) and pilot diesel dual-fuel. One-dimensional (1D) and three-dimensional (3D) computational fluid dynamics (CFD) code and multiobjective optimization code were employed to investigate the influence of CBG-diesel dual-fuel combustion performance and exhaust emissions on a diesel engine. In this paper, 1D engine code and multiobjective optimization code were coupled and evaluated about 15000 cases to define the proper boundary conditions. In addition, selected single diesel fuel (dodecane) and dual-fuel (CBG-diesel) combustion modes were modeled to compare the engine performances and exhaust emission characteristics by using CFD code under various operating conditions. In optimization study, start of pilot diesel fuel injection, CBG-diesel flow rate, and engine speed were optimized and selected cases were compared using CFD code. CBG and diesel fuels were defined as leading reactants using user defined code. The results showed that significantly lower NOx emissions were emitted under dual-fuel operation for all cases compared to single-fuel mode at all engine load conditions.

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

Fuel Injection Strategy for Clean Diesel Engine Using Ethanol Blended Diesel Fuel

2005 ◽  
Author(s):  
Ali Mohammadi ◽  
Takuji Ishiyama ◽  
Takaaki Kakuta ◽  
Sung-Sub Kee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Strategy ◽  
Clean Diesel

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

Towards Primary Breakup Simulation of a Complete Aircraft Nozzle at Realistic Aircraft Conditions

2020 ◽  
Author(s):  
Katharina Warncke ◽  
Amsini Sadiki ◽  
Max Staufer ◽  
Christian Hasse ◽  
Johannes Janicka
Keyword(s):  
Numerical Simulations ◽  
Liquid Fuel ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Nozzle Geometry ◽  
Nozzle Flow ◽  
Spray Characteristics ◽  
Wide Range ◽  
Primary Breakup ◽  
Turbulent Scales

Abstract Predicting details of aircraft engine combustion by means of numerical simulations requires reliable information about spray characteristics from liquid fuel injection. However, details of liquid fuel injection are not well documented. Indeed, standard droplet distributions are usually utilized in Euler-Lagrange simulations of combustion. Typically, airblast injectors are employed to atomize the liquid fuel by feeding a thin liquid film in the shear zone between two swirled air flows. Unfortunately, droplet data for the wide range of operating conditions during a flight is not available. Focusing on numerical simulations, Direct Numerical simulations (DNS) of full nozzle designs are nowadays out of scope. Reducing numerical costs, but still considering the full nozzle flow, the embedded DNS methodology (eDNS) has been introduced within a Volume of Fluid framework (Sauer et al., Atomization and Sprays, vol. 26, pp. 187–215, 2016). Thereby, DNS domain is kept as small as possible by reducing it to the primary breakup zone. It is then embedded in a Large Eddy Simulation (LES) of the turbulent nozzle flow. This way, realistic turbulent scales of the nozzle flow are included, when simulating primary breakup. Previous studies of a generic atomizer configuration proved that turbulence in the gaseous flow has significant impact on liquid disintegration and should be included in primary breakup simulations (Warncke et al., ILASS Europe, Paris, 2019). In this contribution, an industrial airblast atomizer is numerically investigated for the first time using the eDNS approach. The complete nozzle geometry is simulated, considering all relevant features of the flow. Three steps are necessary: 1. LES of the gaseous nozzle flow until a statistically stationary flow is reached. 2. Position and refinement of the DNS domain. Due to the annular nozzle design the DNS domain is chosen as a ring. It comprises the atomizing edge, where the liquid is brought between inner and outer air flow, and the downstream primary breakup zone. 3. Start of liquid fuel injection and primary breakup simulation. Since the simulation of the two-phase DNS and the LES of the surrounding nozzle flow are conducted at the same time, turbulent scales of the gas flow are directly transferred to the DNS domain. The applicability of eDNS to full nozzle designs is demonstrated and details of primary breakup at the nozzle outlet are presented. In particular a discussion of the phenomenological breakup process and spray characteristics is provided.

Bio Diesel Oil of Mustard

2013 ◽  
Vol 5 (1) ◽  
pp. 37-49
Author(s):  
Liu Hongcong
Keyword(s):  
Renewable Energy ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Irrigation System ◽  
Standard Procedure ◽  
Diesel Oil ◽  
Operating Conditions ◽  
Mustard Oil ◽  
Mustard Seed ◽  
Complex Deformation

This paper represents the mustard oil is a kind of renewable energy and alternative fuel of the future. In order to cope with the current situation of load shedding, and reduce dependence on imported fuels, the Bangladesh government to encourage the use of renewable energy. Because the diesel engine with multiple functions, including small pumping irrigation system and backup generators, diesel fuel is much higher than that of any other gasoline fuel. In Bangladesh, mustard oil used as edible oil has been all over the country. Mustard is a widely grown plants, more than demand in Bangladesh and the mustard seed is produced annually. Therefore, to use the remaining mustard oil diesel fuel as a substitute. Fuel properties determine the standard procedure in fuel testing laboratory. An experimental device, and then a small diesel engine made in a laboratory using different conversion from the properties of biodiesel blend of mustard oil. The study found, biodiesel diesel fuel has a slightly different than the property. Also observed, and bio diesel, engine is able to without difficulty, but deviates from its optimal performance. Biodiesel was different (B20, B30, B50) of the blends have been used in engine or a fuel supply system, in order to avoid the complex deformation. Finally, it has been carried out to compare the performance of different operating conditions with different blends of Biodiesel Engine, in order to determine the optimal blends.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

scholarly journals Eucalyptus Biodiesel as an Alternative to Diesel Fuel: Preparation and Tests on DI Diesel Engine

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Lyes Tarabet ◽  
Khaled Loubar ◽  
Mohand Said Lounici ◽  
Samir Hanchi ◽  
Mohand Tazerout
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Second Phase ◽  
Oil Consumption ◽  
Unburned Hydrocarbon ◽  
Engine Combustion ◽  
Di Diesel Engine

Nowadays, the increasing oil consumption throughout the world induces crucial economical, security, and environmental problems. As a result, intensive researches are undertaken to find appropriate substitution to fossil fuels. In view of the large amount of eucalyptus trees present in arid areas, we focus in this study on the investigation of using eucalyptus biodiesel as fuel in diesel engine. Eucalyptus oil is converted by transesterification into biodiesel. Eucalyptus biodiesel characterization shows that the physicochemical properties are comparable to those of diesel fuel. In the second phase, a single cylinder air-cooled, DI diesel engine was used to test neat eucalyptus biodiesel and its blends with diesel fuel in various ratios (75, 50, and 25 by v%) at several engine loads. The engine combustion parameters such as peak pressure, rate of pressure rise, and heat release rate are determined. Performances and exhaust emissions are also evaluated at all operating conditions. Results show that neat eucalyptus biodiesel and its blends present significant improvements of carbon monoxide, unburned hydrocarbon, and particulates emissions especially at high loads with equivalent performances to those of diesel fuel. However, the NOx emissions are slightly increased when the biodiesel content is increased in the blend.

Sign in / Sign up

Export Citation Format

Share Document