Effects of Tip Endwall Contouring on the Three-Dimensional Flow Field in an Annular Turbine Nozzle Guide Vane: Part 2—Numerical Investigation

1986 ◽  
Vol 108 (2) ◽  
pp. 426-428 ◽  
Author(s):  
T. Arts
Keyword(s):  
Flow Field ◽  
Numerical Investigation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

scholarly journals Effects of Tip Endwall Contouring on the Three Dimensional Flow Field in an Annular Turbine Nozzle Guide Vane: Part 2 — Numerical Investigation

1985 ◽  
Author(s):  
Tony Arts
Keyword(s):  
Flow Field ◽  
Numerical Investigation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Contour Plots ◽  
Endwall Contouring ◽  
Nozzle Guide

This paper describes the numerical investigation of the three dimensional flow through a low speed, low aspect ratio, high turning annular turbine nozzle guide vane with meridional tip endwall contouring. This rotational flow field has been simulated using a finite volume discretization and a time marching technique to solve the three dimensional, time dependent Euler equations expressed in a cylindrical coordinates system. The results are presented under the form of contour plots, spanwise pitch-averaged distributions and blade static pressure distributions. Detailed comparisons with the measurements described in part I of the paper are also provided.

Effects of Tip Endwall Contouring on the Three-Dimensional Flow Field in an Annular Turbine Nozzle Guide Vane: Part 1—Experimental Investigation

1985 ◽  
Vol 107 (4) ◽  
pp. 983-990 ◽  
Author(s):  
E. Boletis
Keyword(s):  
Experimental Investigation ◽  
Aspect Ratio ◽  
Guide Vane ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Low Aspect Ratio ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

Tip endwall contouring is one of the most effective methods to improve the performance of low aspect ratio turbine vanes [1]. In view of the wide variety of geometric parameters, it appears that only the physical understanding of the three-dimensional flow field will allow us to evaluate the probable benefits of a particular endwall contouring. The paper describes the experimental investigation of the three-dimensional flow through a low-speed, low aspect ratio, high-turning annular turbine nozzle guide vane with meridional tip endwall contouring. The full impact of the effects of tip contouring is evaluated by comparison with the results of a previous study in an annular turbine nozzle guide vane of the same blade and cascade geometry with cylindrical endwalls [12]. In parallel, the present experimental study provides a fully three-dimensional test case for comparison with advanced theoretical calculation methods [15]. The flow is explored by means of double-head, four-hole pressure probes in five axial planes from far upstream to downstream of the blade row. The results are presented in the form of contour plots and spanwise pitch-averaged distributions.

The Influence of Endwall Contouring on the Performance of a Turbine Nozzle Guide Vane

1998 ◽  
Author(s):  
Vincenzo Dossena ◽  
Antonio Perdichizzi ◽  
Marco Savini
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Guide Vane ◽  
Three Dimensional ◽  
Angle Distribution ◽  
Secondary Effects ◽  
Three Dimensional Flow ◽  
Nozzle Height ◽  
Dimensional Flow ◽  
Endwall Contouring

The paper presents the results of a detailed investigation of the flow field in a gas turbine linear cascade. A comparison between a contoured and a planar configuration of the same cascade has been performed, and differences in the three-dimensional flow field are here analyzed and discussed. The flow evolution downstream of the trailing edge was surveyed by means of probe traversing while a 3-D Navier-Stokes solver was employed to obtain information on flow structures inside the vaned passages. The experimental measurements and the numerical simulation of the three-dimensional flow field has been performed for two cascades; one with planar endwalls, and the other with one planar and one profiled endwall, so as to present a reduction of the nozzle height. The investigation was carried out at an isentropic downstream Mach number of 0.6. Airfoils of both cascades were scaled from the same high pressure gas turbine inlet guide vane. Measurements of the three-dimensional flow field have been performed on five planes downstream of the cascades by means of a miniaturized five-hole pressure probe. The presence of endwall contouring strongly influences the secondary effects; the vortex generation and their development is inhibited by the stronger acceleration taking place throughout the cascade. The results show that the secondary effects on the contoured side of the passage are confined in the endwall region, while on the flat side the secondary vortices display characteristics similar to the ones occurring downstream of the planar cascade. The spanwise outlet angle distribution presents a linear variation for most of the nozzle height, with quite low values approaching the contoured endwall. The analysis of mass averaged losses shows a significant performance improvement in the contoured cascade. This has to be ascribed not only to lower secondary losses but also to a reduction of the profile losses.

Numerical Analysis on Effects of the Contoured Endwall on the Three Dimensional Flow Characteristics in an Annular Turbine Nozzle Vane

2007 ◽  
Author(s):  
Wu Sang Lee ◽  
Jin Taek Chung ◽  
Dae Hyun Kim ◽  
Seung Joo Choe
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Leading Edge ◽  
Secondary Flows ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The three-dimensional flow in a turbine nozzle guide vane passage causes large secondary loss through the passage and increased heat transfer on the blade surface. In order to reduce or control these secondary flows, a linear turbine with contoured endwall configurations was used and changes in the three-dimensional flow field were analyzed and discussed. Contoured endwalls are installed at a location downstream of the saddle point near the leading edge of the pressure side blade and several positions along the centerline of the passage at constant distance. The objective of this study is to document the development of the three-dimensional flow in a turbine nozzle guide vane cascade with modified endwall. In addition, it proposes and appropriates endwall contouring which shows best overall loss reduction performance among the simulated contoured endwall. The results of this study show that the development of passage vortex and cross flow in the cascade composed of one flat and one contoured endwalls are affected by the acceleration which occurs in contoured endwall side. The overall loss is reduced near the flat endwall rather than contoured endwall, the best performance was shown for the case of 10–15% contoured for span-wise, 40–70% length of chord from trailing edge.

The Influence of Endwall Contouring on the Performance of a Turbine Nozzle Guide Vane

1999 ◽  
Vol 121 (2) ◽  
pp. 200-208 ◽  
Author(s):  
V. Dossena ◽  
A. Perdichizzi ◽  
M. Savini
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Guide Vane ◽  
Three Dimensional ◽  
Angle Distribution ◽  
Secondary Effects ◽  
Three Dimensional Flow ◽  
Nozzle Height ◽  
Dimensional Flow ◽  
Endwall Contouring

The paper presents the results of a detailed investigation of the flow field in a gas turbine linear cascade. A comparison between a contoured and a planar configuration of the same cascade has been performed, and differences in the three-dimensional flow field are here analyzed and discussed. The flow evolution downstream of the trailing edge was surveyed by means of probe traversing while a three-dimensional Navier–Stokes solver was employed to obtain information on flow structures inside the vaned passages. The experimental measurements and the numerical simulation of the three-dimensional flow field have been performed for two cascades; one with planar endwalls, and the other with one planar and one profiled endwall, so as to present a reduction of the nozzle height. The investigation was carried out at an isentropic downstream Mach number of 0.6. Airfoils of both cascades were scaled from the same high-pressure gas turbine inlet guide vane. Measurements of the three-dimensional flow field have been performed on five planes downstream of the cascades by means of a miniaturized five-hole pressure probe. The presence of endwall contouring strongly influences the secondary effects; the vortex generation and their development are inhibited by the stronger acceleration taking place throughout the cascade. The results show that the secondary effects on the contoured side of the passage are confined in the endwall region, while on the flat side the secondary vortices display characteristics similar to the ones occurring downstream of the planar cascade. The spanwise outlet angle distribution presents a linear variation for most of the nozzle height, with quite low values approaching the contoured endwall. The analysis of mass-averaged losses shows a significant performance improvement in the contoured cascade. This can be ascribed not only to lower secondary losses but also to a reduction of the profile losses.

Flow Measurements in a Nozzle Guide Vane Passage With a Low Aspect Ratio and Endwall Contouring

2000 ◽  
Author(s):  
Steven W. Burd ◽  
Terrence W. Simon
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Guide Vane ◽  
Flow Measurements ◽  
Vast Number ◽  
Aspect Ratios ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

The vast number of turbine cascade studies in the literature has been performed in straight-endwall, high-aspect-ratio, linear cascades. As a result, there has been little appreciation for the role of, and added complexity imposed by, reduced aspect ratios. There also has been little documentation of endwall profiling at these reduced spans. To examine the role of these factors on cascade hydrodynamics, a large-scale nozzle guide vane simulator was constructed at the Heat Transfer Laboratory of the University of Minnesota. This cascade is comprised of three airfoils between one contoured and one flat endwall. The geometries of the airfoils and endwalls, as well as the experimental conditions in the simulator, are representative of those in commercial operation. Measurements with hot-wire anemometry were taken to characterize the flow approaching the cascade. These measurements show that the flow field in this cascade is highly elliptic and influenced by pressure gradients that are established within the cascade. Exit flow field measurements with triple-sensor anemometry and pressure measurements within the cascade indicate that the acceleration imposed by endwall contouring and airfoil turning is able to suppress the size and strength of key secondary flow features. In addition, the flow field near the contoured endwall differs significantly from that adjacent to the straight endwall.

scholarly journals Wake Region Measurements of a Highly Three-Dimensional Nozzle Guide Vane Tested at DRA Pyestock Using Particle Image Velocimetry

1994 ◽  
Author(s):  
M. Funes-Gallanzi ◽  
P. J. Bryanston-Cross ◽  
K. S. Chana
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Guide Vane ◽  
Three Dimensional ◽  
Light Sheet ◽  
Test Facility ◽  
Velocity Mapping ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Annular Cascade

The quantitative whole field flow visualization technique of PIV has over the last few years been successfully demonstrated for transonic flow applications. A series of such measurements has been made at DRA Pyestock. Several of the development stages critical to a full engine application of the work have now been achieved using the Isentropic Light Piston Cascade (ILPC) test facility operating with high inlet turbulence levels: • A method of seeding the flow with 0.5μm diameter styrene particles has provided an even coverage of the flow field. • A method of projecting a 1 mm thick high power Nd/YAG laser light sheet within the turbine stator cascade. This has enabled a complete instantaneous intra-blade velocity mapping of the flow field to be visualized, by a specially developed diffraction-limited optics arrangement. • Software has been developed to automatically analyze the data. Due to the sparse nature of the data obtained, a spatial approach to the extraction of the velocity vector data was employed. • Finally, a comparison of the experimental results with those obtained from a three-dimensional viscous flow program of Dawes; using the Baldwin-Lomax model for eddy viscosity and assuming fully turbulent flow. The measurements provide an instantaneous quantitative whole field visualization of a high-speed unsteady region of flow in a highly three-dimensional nozzle guide vane; which has been successfully compared with a full viscous calculation. This work represents the first such measurements to be made in a full-size transonic annular cascade at engine representative conditions.

Experimental Study of the Flow Field Behind an Annular Turbine Nozzle Guide Vane With and Without Downstream Rotor

1984 ◽  
Author(s):  
E. Boletis ◽  
C. H. Sieverding
Keyword(s):  
Flow Field ◽  
Guide Vane ◽  
Three Dimensional ◽  
Rotor Blades ◽  
Pressure Probe ◽  
Flow Conditions ◽  
Nozzle Guide Vane ◽  
Contour Plots ◽  
Real Flow ◽  
Nozzle Guide

Measurements of the three dimensional flow field in annular turbine nozzle guide vanes present an important step in the simulation of the real flow conditions in turbomachinery bladings. This paper seeks to determine whether the installation of a rotor closely behind a high hub-to-tip ratio cascade (DH/DT=0.8) is indispensable for establishing correct flow conditions at the cascade exit or whether the use of an axial diffuser of a certain length is sufficient. Also, an attempt is made to separate the possible effects of the rotor blades from that of the rotating rotor disc. The tests are carried out on a low speed, low aspect ratio, high turning nozzle guide vane. The flow is explored by means of a double head four-hole pressure probe and the results are presented in the form of contour plots and spanwise pitch-averaged distributions of losses, flow angles and static pressure.

Flow Measurements in a Nozzle Guide Vane Passage With a Low Aspect Ratio and Endwall Contouring

2000 ◽  
Vol 122 (4) ◽  
pp. 659-666 ◽  
Author(s):  
Steven W. Burd ◽  
Terrence W. Simon
Keyword(s):  
Aspect Ratio ◽  
Flow Field ◽  
Large Scale ◽  
Guide Vane ◽  
Flow Measurements ◽  
Aspect Ratios ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

Most turbine cascade studies in the literature have been performed in straight-endwall, high-aspect-ratio, linear cascades. As a result, there has been little appreciation for the role of, and added complexity imposed by, reduced aspect ratios. There also has been little documentation of endwall profiling with these reduced spans. To examine the role of these factors on cascade hydrodynamics, a large-scale nozzle guide vane simulator was constructed at the Heat Transfer Laboratory of the University of Minnesota. This cascade is comprised of three airfoils between one contoured and one flat endwall. The geometries of the airfoils and endwalls, as well as the experimental conditions in the simulator, are representative of those in commercial operation. Measurements with hot-wire anemometry were taken to characterize the flow approaching the cascade. These measurements show that the flow field in this cascade is highly elliptic and influenced by pressure gradients that are established within the cascade. Exit flow field measurements with triple-sensor anemometry and pressure measurements within the cascade indicate that the acceleration imposed by endwall contouring and airfoil turning is able to suppress the size and strength of key secondary flow features. In addition, the flow field near the contoured endwall differs significantly from that adjacent to the straight endwall. [S0889-504X(00)01104-1]

Sign in / Sign up

Export Citation Format

Share Document