Experimental Heat Transfer Investigation Around the Film-Cooled Leading Edge of a High-Pressure Gas Turbine Rotor Blade

1985 ◽  
Vol 107 (4) ◽  
pp. 1016-1021 ◽  
Author(s):  
C. Camci ◽  
T. Arts
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Rotor Blade ◽  
Free Stream ◽  
Leading Edge ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
Turbine Rotor Blade ◽  
Experimental Heat ◽  
Experimental Heat Transfer

This paper describes an experimental heat transfer investigation around the leading edge of a high-pressure film-cooled gas turbine rotor blade. The measurements were performed in the VKI isentropic compression tube facility using platinum thin film gauges painted on a blade made of machinable glass ceramic. Free-stream to wall temperature ratio, Reynolds, and Mach numbers were selected from actual aeroengines conditions. Heat transfer data obtained without and with film cooling in a stationary frame are presented. The effects of coolant to free-stream mass weight ratio and temperature ratio were successively investigated. Heat transfer modifications due to incidence angle variations were interpreted with the aid of inviscid flow calculation methods.

scholarly journals Navier–Stokes Analysis of Turbine Blade Heat Transfer

1991 ◽  
Vol 113 (3) ◽  
pp. 392-403 ◽  
Author(s):  
R. J. Boyle
Keyword(s):  
Heat Transfer ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Free Stream Turbulence ◽  
Eddy Viscosity Model ◽  
Experimental Heat ◽  
Experimental Heat Transfer

Comparisons with experimental heat transfer and surface pressures were made for seven turbine vane and blade geometries using a quasi-three-dimensional thin-layer Navier–Stokes analysis. Comparisons are made for cases with both separated and unseparated flow over a range of Reynolds numbers and free-stream turbulence intensities. The analysis used a modified Baldwin-Lomax turbulent eddy viscosity model. Modifications were made to account for the effects of: (1) free-stream turbulence on both transition and leading edge heat transfer; (2) strong favorable pressure gradients on relaminarizations; and (3) variable turbulent Prandtl number on heat transfer. In addition, the effect on heat transfer of the near-wall model of Deissler is compared with the Van Driest model.

Toward Improved Film Cooling Prediction

2002 ◽  
Vol 124 (2) ◽  
pp. 193-199 ◽  
Author(s):  
G. Medic ◽  
P. A. Durbin
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Rotor Blade ◽  
Energy Production ◽  
Turbulence Models ◽  
Turbine Rotor ◽  
Turbulence Energy ◽  
Turbine Rotor Blade ◽  
Flow And Heat Transfer

Computations of flow and heat transfer for a film-cooled high pressure gas turbine rotor blade geometry are presented with an assessment of several turbulence models. Details of flow and temperature field predictions in the vicinity of cooling holes are examined. It is demonstrated that good predictions can be obtained when spurious turbulence energy production by the turbulence model is prevented.

Comparison of Time-Resolved Turbine Rotor Blade Heat Transfer Measurements and Numerical Calculations

1991 ◽  
Author(s):  
R. S. Abhari ◽  
G. R. Guenette ◽  
A. H. Epstein ◽  
M. B. Giles
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Time History ◽  
Turbine Rotor ◽  
Numerical Calculations ◽  
Test Facility ◽  
Time Resolved ◽  
Turbine Rotor Blade ◽  
History Of

Time-resolved turbine rotor blade heat transfer data are compared with ab initio numerical calculations. The data was taken on a transonic, 4-to-1 pressure ratio, uncooled, single-stage turbine in a short duration turbine test facility. The data consists of the time history of the heat transfer distribution about the rotor chord at midspan. The numerical calculation is a time accurate, 2-D, thin shear layer, multiblade row code known as UNSFLO. UNSFLO uses Ni’s Lax-Wendroff algorithm, conservative boundary conditions, and a time tilting algorithm to facilitate the calculation of the flow in multiple blade rows of arbitrary pitch ratio with relatively little computer time. The version used for this work had a simple algebraic Baldwin-Lomax turbulence model. The code is shown to do a good job of predicting the quantitative time history of the heat flux distribution. The wake/boundary layer and transonic interaction regions for suction and pressure surfaces are identified and the shortcomings of the current algebraic turbulence modelling in the code are discussed. The influence of hardware manufacturing tolerance on rotor heat transfer variation is discussed. A physical reasoning explaining the discrepancies between the unsteady measurement and the calculations for both the suction and pressure surfaces are given, which may be of use in improving future calculations and design procedures.

scholarly journals Analysis of Gas Turbine Rotor Blade Tip and Shroud Heat Transfer

1996 ◽  
Author(s):  
A. A. Ameri ◽  
E. Steinthorsson
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Stokes Equations ◽  
Computer Code ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Turbine Rotor Blade ◽  
Blade Tip

Predictions of the rate of heat transfer to the tip and shroud of a gas turbine rotor blade are presented. The simulations are performed with a multiblock computer code which solves the Reynolds Averaged Navier-Stokes equations. The effect of inlet boundary layer thickness as well as rotation rate on the tip and shroud heat transfer is examined. The predictions of the blade tip and shroud heat transfer are in reasonable agreement with the experimental measurements. Areas of large heat transfer rates are identified and physical reasoning for the phenomena presented.

Comparison of Time-Resolved Turbine Rotor Blade Heat Transfer Measurements and Numerical Calculations

1992 ◽  
Vol 114 (4) ◽  
pp. 818-827 ◽  
Author(s):  
R. S. Abhari ◽  
G. R. Guenette ◽  
A. H. Epstein ◽  
M. B. Giles
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Time History ◽  
Turbine Rotor ◽  
Numerical Calculations ◽  
Test Facility ◽  
Time Resolved ◽  
Turbine Rotor Blade ◽  
History Of

Time-resolved turbine rotor blade heat transfer data are compared with ab initio numerical calculations. The data were taken on a transonic, 4-to-1 pressure ratio, uncooled, single-stage turbine in a short-duration turbine test facility. The data consist of the time history of the heat transfer distribution about the rotor chord at midspan. The numerical calculation is a time accurate, two-dimensional, thin shear layer, multiblade row code known as UNSFLO. UNSFLO uses Ni’s Lax-Wendroff algorithm, conservative boundary conditions, and a time tilting algorithm to facilitate the calculation of the flow in multiple blade rows of arbitrary pitch ratio with relatively little computer time. The version used for this work had a simple algebraic Baldwin-Lomax turbulence model. The code is shown to do a good job of predicting the quantitative time history of the heat flux distribution. The wake/boundary layer and transonic interaction regions for suction and pressure surfaces are identified and the shortcomings of the current algebraic turbulence modeling in the code are discussed. The influence of hardware manufacturing tolerance on rotor heat transfer variation is discussed. A physical reasoning explaining the discrepancies between the unsteady measurement and the calculations for both the suction and pressure surfaces are given, which may be of use in improving future calculations and design procedures.

Sign in / Sign up

Export Citation Format

Share Document