Distinction Between Different Types of Impeller and Diffuser Rotating Stall in a Centrifugal Compressor With Vaneless Diffuser

1984 ◽  
Vol 106 (2) ◽  
pp. 468-474 ◽  
Author(s):  
P. Frigne ◽  
R. Van Den Braembussche
Keyword(s):  
Experimental Data ◽  
Experimental Investigation ◽  
Centrifugal Compressor ◽  
Rotating Stall ◽  
Rotating Flow ◽  
Hot Wire ◽  
Vaneless Diffuser ◽  
Velocity Fluctuations ◽  
Different Types ◽  
Induced Velocity

This paper describes the results of an experimental investigation of the sub-synchronous rotating flow patterns in a centrifugal compressor with vaneless diffuser. Several compressor configurations have been examined by means of hot wire anemometry, Fourier analysis allowed one to distinguish between the different modes of unstable operation. For both impeller and diffuser rotating stall, comparison is made between the amplitude, frequency, and periodicity of the induced velocity fluctuations. The results are further cross-checked with other experimental data.

Geometric considerations in the capture of localized flow reversal in centrifugal compressor vaneless diffusers using steady state simulations

2016 ◽  
Vol 231 (21) ◽  
pp. 3959-3973
Author(s):  
Chris Clarke ◽  
Russell Marechale ◽  
Abraham Engeda ◽  
Michael Cave
Keyword(s):  
Experimental Data ◽  
Steady State ◽  
Centrifugal Compressor ◽  
Flow Characteristics ◽  
Rotating Stall ◽  
Flow Reversal ◽  
Contour Plot ◽  
Vaneless Diffuser ◽  
Impeller Blade ◽  
Steady State Simulation

A steady state simulation procedure is proposed to capture localized flow reversal inside of a centrifugal compressor vaneless diffuser. The procedure was performed on 12 compressor stages of varying geometry for speed lines of 13,100, 19,240, and 21,870 r/min. The simulations were run for all points from choke to surge including the experimentally determined rotating stall onset point. The experimental data and geometry were provided by Solar Turbines Inc. San Diego, CA. It was found possible to capture localized flow reversal inside of a vaneless diffuser using a steady state simulation. The results showed that using a geometric parameter, comparing the diffuser width, b4, to the impeller blade pitch distance, dpitch, it could be determined whether or not a steady state simulation could capture localized flow reversal. For values of b4/dpitch beneath 0.152 flow reversal could not be captured. But, for values of b4/dpitch above 0.177 localized flow reversal was captured. For values between 0.152 and 0.177, no conclusions could be drawn. Where possible, experimental data were compared against the diffuser inlet and outlet numerical profiles and the meridional contour plot. These comparisons served to validate the approach used in this article. These validations showed that the procedure defined herein is accurate and trustworthy within a specific range of geometric and flow characteristics. There are two other conclusions. First, the b4/dpitch parameter helps to define the type of flow breakdown. For b4/dpitch below 0.152, the flow breaks down in the circumferential direction, but for values of b4/dpitch above 0.177, the flow breaks down in the span-wise direction. Second, the simulations were able to capture instances of localized flow reversal before rotating stall onset. This concludes that localized flow reversal is not the determining factor in rotating stall onset as has been suggested by other investigators.

A Distinction Between Different Types of Stall in a Centrifugal Compressor Stage

1986 ◽  
Vol 108 (1) ◽  
pp. 83-92 ◽  
Author(s):  
N. Ka¨mmer ◽  
M. Rautenberg
Keyword(s):  
Energy Transfer ◽  
Centrifugal Compressor ◽  
High Frequency ◽  
Low Frequency ◽  
Rotating Stall ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Pressure Transducers ◽  
Different Types ◽  
Probe Measurements

The flow at the stall line of a centrifugal compressor with vaneless diffuser was investigated at different speeds. A distinction between three kinds of stall phenomena could be made. One type of stall with regurgitation of fluid at the impeller inlet was of a nonperiodic character, whereas two different types of periodic stall appeared at higher speeds. The rotating nature of these two types of stall was verified from a comparison of signals of peripherally spaced pressure transducers. The low-frequency rotating stall exhibited features of diffuser generated stall and a lobe number of three was measured. From a detailed investigation of the high-frequency rotating stall, which included unsteady probe measurements upstream and downstream of the impeller, it can be shown that this type of rotating stall is generated in the impeller by a periodic breakdown of energy transfer from the rotor to the flow. This conclusion is supported by the distribution of shroud static pressures.

Experimental Investigation and Characterization of the Rotating Stall in a High Pressure Centrifugal Compressor: Part IV — Impeller Influence on Diffuser Stability

2003 ◽  
Author(s):  
A. Cellai ◽  
G. Ferrara ◽  
L. Ferrari ◽  
C. P. Mengoni ◽  
L. Baldassarre
Keyword(s):  
Experimental Investigation ◽  
High Pressure ◽  
Centrifugal Compressor ◽  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Stall Inception ◽  
Last Stage ◽  
And Diffusion

Vaneless diffuser rotating stall is a major problem for centrifugal compressors since it is a limit to their working range. In particular the last stage seems to be the most critical. In the literature some good correlations for predicting stall inception can be found but they do not adequately cover the case of the last stage configuration, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. Extensive research has been performed to define diffuser stall limits for this family of stages: three impellers characterized by different blade-outlet-width-to-impeller-radius-ratios are tested with different diffuser configurations (different pinch shapes, diffuser widths and diffusion ratios). Part I and II report the results of these geometry modifications on diffuser stability for the first impeller. Part III, those for the second impeller. In this part the comparison of these results in terms of impeller influence on diffuser stability is reported.

scholarly journals Comparative Rotating Stall and Surge Characteristic of a Centrifugal Compressor With Three Different Types of Diffusers

1997 ◽  
Author(s):  
Abraham Engeda
Keyword(s):  
Centrifugal Compressor ◽  
Rotating Stall ◽  
Straight Channel ◽  
Vaneless Diffuser ◽  
Curved Channel ◽  
Vaned Diffuser ◽  
Channel Geometry ◽  
Different Types ◽  
Specific Geometry ◽  
Tip Radius

The diffuser system of a centrifugal compressor comes basically in two general categories either as vaneless or vaned diffuser. Vaned diffusers can further be subdivided into two depending on channel geometry as straight channel or curved channel, or depending on solidity. Three different diffuser types: a vaneless, conventional vaned and a low solidity vaned were tested in the present study. All diffusers were tested downstream of the same impeller. All the diffusers had the same diffuser exit radius to impeller tip radius ratio. The influence of each type of diffuser on the performance and stall characteristics of the inducer and impeller as a whole was studied. In addition, diffuser stall characteristics of each type diffuser were also studied. The type of diffuser had no significant effect on inducer and impeller stall. The inducer was more stable with the conventional vaned diffuser configuration. Rotating Stall was detected with the vaneless diffuser configuration at the onset of surge. Four stall cells rotated in the same direction as the impeller at 122 Hz. Numerous works have been documented on rotating stall and surge for centrifugal compressors. Prediction of the inception of rotating stall and surge for a specific geometry and operation is not yet fully possible. Therefore, experimental results and correlations are still of great importance.

Experimental Investigation of Rotating Instabilities in a Two-Stage Centrifugal Compressor With Vaneless Diffuser

2001 ◽  
Author(s):  
Vladimir V. Golubev
Keyword(s):  
Experimental Investigation ◽  
Centrifugal Compressor ◽  
Pressure Fluctuations ◽  
Rotating Stall ◽  
Sensitive Area ◽  
Flow Conditions ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Two Stage ◽  
Multi Stage

Abstract This paper examines unsteady response of an experimental two-stage centrifugal compressor with vaneless diffusers. A thorough investigation of pressure fluctuations along the compressor channel is carried out in order to examine the onset of unstable flow conditions. Rotating stall structures are localized, with special attention paid to identifying the most sensitive area of the multi-stage compressor channel which may serve as a precursor to unstable compressor operation. It is shown that both stages may develop rotating stall structures simultaneously, however the 2nd stage tends to destabilize first and reveals higher magnitudes of the unsteady response.

The Influence of a Diffuser Width on the Unsteady Performance of a Centrifugal Compressor Stage

2002 ◽  
Author(s):  
Abraham Engeda
Keyword(s):  
Centrifugal Compressor ◽  
Time Domain ◽  
Rotating Stall ◽  
Compressor Stage ◽  
Relative Speed ◽  
Vaneless Diffuser ◽  
Flow Rates ◽  
Centrifugal Compressor Stage ◽  
Different Types ◽  
Unsteady Performance

An experimental investigation was conducted to determine the effect of the vaneless diffuser width on the unsteady flow performance of a centrifugal compressor stage. Two compressor configurations with different vaneless diffuser width were investigated at four different impeller speeds and compared in the frequency and time domain. Only one diffuser rotating stall but different types of impeller rotating stalls were detected. The experiments show that the diffuser has a strong influence on the flow in the impeller including in areas way upstream. Analysis of the results indicated: • With increasing diffuser width the onset of impeller rotating stall was shifted to lower flow rates. • With increasing diffuser width the frequencies of the rotating stalls decreased. • There is a common tendency in most of the experiments to lower numbers of rotating cells with increasing relative speed. The impeller rotating stalls can be subdivided in a slow pattern with a relative speed to the impeller of 0.21 to 0.29 and a fast pattern with a relative speed of 0.50 to 0.56. This occurrence of two rotating pressure patterns confirms analytical results presented in previous investigations.

Separation in oscillating laminar boundary-layer flows

1971 ◽  
Vol 47 (1) ◽  
pp. 21-31 ◽  
Author(s):  
R. A. Despard ◽  
J. A. Miller
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Reverse Flow ◽  
Oscillation Amplitude ◽  
Hot Wire ◽  
Boundary Layer Flows ◽  
Laminar Boundary Layers ◽  
History Of

The results of an experimental investigation of separation in oscillating laminar boundary layers is reported. Instantaneous velocity profiles obtained with multiple hot-wire anemometer arrays reveal that the onset of wake formation is preceded by the initial vanishing of shear at the wall, or reverse flow, throughout the entire cycle of oscillation. Correlation of the experimental data indicates that the frequency, Reynolds number and dynamic history of the boundary layer are the dominant parameters and oscillation amplitude has a negligible effect on separation-point displacement.

Effects of Non-Axisymmetric Volute on Rotating Stall in the Vaneless Diffuser of a Centrifugal Compressor

2020 ◽  
Author(s):  
Zitian Niu ◽  
Zhenzhong Sun ◽  
Baotong Wang ◽  
Xinqian Zheng
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Stability Boundary ◽  
Rotating Stall ◽  
Evolution Process ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Centrifugal Compressors ◽  
Specific Location

Abstract Rotating stall is an important unstable flow phenomenon that leads to performance degradation and limits the stability boundary in centrifugal compressors. The volute is one of the sources to induce the non-axisymmetric flow in a centrifugal compressor, which has an important effect on the performance of compressors. However, the influence of volute on rotating stall is not clear. Therefore, the effects of volute on rotating stall by experimental and numerical simulation have been explored in this paper. It’s shown that one rotating stall cell generates in a specific location and disappears in another specific location of the vaneless diffuser as a result of the distorted flow field caused by the volute. Also, the cells cannot stably rotate in a whole circle. The frequency related to rotating stall captured in the experiment is 43.9% of the impeller passing frequency (IPF), while it is 44.7% of IPF captured by three-dimensional unsteady numerical simulation, which proves the accuracy of the numerical method in this study. The numerical simulation further reveals that the stall cell initialized in a specific location can be split into several cells during the evolution process. The reason for this is that the blockage in the vaneless diffuser induced by rotating stall is weakened by the mainstream from the impeller exit to make one initialized cell disperse into several ones. The volute has an important influence on the generation and evolution process of the rotating stall cells of compressors. By optimizing volute geometry to reduce the distortion of the flow field, it is expected that rotating stall can be weakened or suppressed, which is helpful to widen the operating range of centrifugal compressors.

Flow Behavior of a Centrifugal Compressor With Vaneless Diffuser at Design and Off Design Conditions

2012 ◽  
Author(s):  
Chuang Gao ◽  
Weiguang Huang ◽  
Haiqing Liu ◽  
Hongwu Zhang ◽  
Jundang Shi
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Travelling Waves ◽  
Leading Edge ◽  
Pressure Oscillation ◽  
Rotating Stall ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Flow Recirculation ◽  
Static Performance

This paper concerns with the numerical and experimental aspects of both steady and unsteady flow behavior in a centrifugal compressor with vaneless diffuser and downstream collector. Specifically, the appearance of flow instabilities i.e., rotating stall and surge is investigated in great detail. As the first step, the static performance of both stage and component was analyzed and possible root cause of system surge was put forward based on the classic stability theory. Then the unsteady pressure data was utilized to find rotating stall and surge in frequency domain which could be classified as mild surge and deep surge. With the circumferentially installed transducers at impeller inlet, backward travelling waves during stall ramp could be observed. The modes of stall waves could be clearly identified which is caused by impeller leading edge flow recirculation at Mu = 0.96. However, for the unstable flow at Mu = 1.08, the system instability seems to be caused by reversal flow in vaneless diffuser where the pressure oscillation was strongest. Thus steady numerical simulation were performed and validated with the experimental performance data. With the help of numerical analysis, the conjectures are proved.

scholarly journals Rotating Stall in Centrifugal Compressor Vaneless Diffuser: Experimental Analysis of Geometrical Parameters Influence on Phenomenon Evolution

2004 ◽  
Vol 10 (6) ◽  
pp. 433-442 ◽  
Author(s):  
Giovanni Ferrara ◽  
Lorenzo Ferrari ◽  
Leonardo Baldassarre
Keyword(s):  
Centrifugal Compressor ◽  
Dynamic Pressure ◽  
Pressure Sensors ◽  
Experimental Tests ◽  
Fast Response ◽  
Rotating Stall ◽  
Geometrical Parameters ◽  
Vaneless Diffuser ◽  
Response Dynamic ◽  
Frequency Domains

The rotating stall is a key problem for achieving a good working range of a centrifugal compressor and a detailed understanding of the phenomenon is very important to anticipate and avoid it. Many experimental tests have been planned by the authors to investigate the influence on stall behavior of different geometrical configurations. A stage with a backward channel upstream, a 2-D impeller with a vaneless diffuser and a constant cross-section volute downstream, constitute the basic configuration. Several diffuser types with different widths, pinch shapes, and diffusion ratios were tested. The stage was instrumented with many fast response dynamic pressure sensors so as to characterize inception and evolution of the rotating stall. This kind of analysis was carried out both in time and in frequency domains. The methodology used and the results on phenomenon evolution will be presented and discussed in this article.

Sign in / Sign up

Export Citation Format

Share Document