Criterion for Allowable Lower Ball Joint Angle in Floating Drilling

1980 ◽  
Vol 102 (4) ◽  
pp. 242-250 ◽  
Author(s):  
J. R. Fowler ◽  
T. N. Gardner
Keyword(s):  
Joint Angle ◽  
Drill Pipe ◽  
Ball Joint ◽  
Joint Angles ◽  
Joint Region ◽  
Wear Rates

In drilling from floating vessels, most operators and drilling contractors specify an allowable lower ball joint angle of 3–5 deg for drilling and 1–3 deg for running casing. Presently, no one uses tension in the drill pipe or casing as a factor in setting allowable ball joint angles. The results of the analysis detailed in this paper show that the allowable ball joint angles in use are justified for well depths less than 5000 ft below the ball joint. However, the allowable angle is too high for continual operation for well depths below the ball joint of 10,000 ft or more. The increased drill pipe or casing tension in deeper wells causes high alternating stresses in the drill pipe and high wear rates where the pipe bears against equipment in the ball joint region. The principal conclusion of this paper is that the allowable lower ball joint angle should not be constant, but should vary with the tension in the drill pipe as the well is being drilled.

The Effect of Tool Joint Stiffness on Drill Pipe Fatigue in Riser Ball Joints

1989 ◽  
Vol 111 (4) ◽  
pp. 369-374 ◽  
Author(s):  
A. Ertas ◽  
W. R. Blackstone ◽  
B. K. Majumdar
Keyword(s):  
Fatigue Damage ◽  
Joint Angle ◽  
Drill Pipe ◽  
Joint Stiffness ◽  
Finite Element Models ◽  
Ball Joint ◽  
Marine Riser ◽  
Joint Angles ◽  
Ball Joints ◽  
Tool Joint

It is well known that the ball joint in a marine riser can cause fatigue damage in the drill pipe passing through. Previous investigators have assessed the damage done for a lower ball joint angle of 3–5 degrees (drilling) and 1–3 degrees (running casing). This paper extends that work to deep water operations in which an upper ball joint is also present. Also, it is shown, via finite element models, that tool joint bending stiffness can have a significant effect on fatigue life. Fatigue damage calculations, including this heretofore unconsidered effect, are presented for various ball joint angles and drill pipe tensions.

scholarly journals Genome-Wide Association Studies Based on Equine Joint Angle Measurements Reveal New QTL Affecting the Conformation of Horses

Genes ◽  
2019 ◽  
Vol 10 (5) ◽  
pp. 370 ◽  
Author(s):  
Annik Imogen Gmel ◽  
Thomas Druml ◽  
Rudolf von Niederhäusern ◽  
Tosso Leeb ◽  
Markus Neuditschko
Keyword(s):  
Joint Angle ◽  
Association Studies ◽  
Genome Wide Association ◽  
Cranial Morphology ◽  
Genome Wide Association Studies ◽  
Joint Angles ◽  
Mineral Density ◽  
Mixed Effect ◽  
Stifle Joint ◽  
Genome Wide

The evaluation of conformation traits is an important part of selection for breeding stallions and mares. Some of these judged conformation traits involve joint angles that are associated with performance, health, and longevity. To improve our understanding of the genetic background of joint angles in horses, we have objectively measured the angles of the poll, elbow, carpal, fetlock (front and hind), hip, stifle, and hock joints based on one photograph of each of the 300 Franches-Montagnes (FM) and 224 Lipizzan (LIP) horses. After quality control, genome-wide association studies (GWASs) for these traits were performed on 495 horses, using 374,070 genome-wide single nucleotide polymorphisms (SNPs) in a mixed-effect model. We identified two significant quantitative trait loci (QTL) for the poll angle on ECA28 (p = 1.36 × 10−7), 50 kb downstream of the ALX1 gene, involved in cranial morphology, and for the elbow joint on ECA29 (p = 1.69 × 10−7), 49 kb downstream of the RSU1 gene, and 75 kb upstream of the PTER gene. Both genes are associated with bone mineral density in humans. Furthermore, we identified other suggestive QTL associated with the stifle joint on ECA8 (p = 3.10 × 10−7); the poll on ECA1 (p = 6.83 × 10−7); the fetlock joint of the hind limb on ECA27 (p = 5.42 × 10−7); and the carpal joint angle on ECA3 (p = 6.24 × 10−7), ECA4 (p = 6.07 × 10−7), and ECA7 (p = 8.83 × 10−7). The application of angular measurements in genetic studies may increase our understanding of the underlying genetic effects of important traits in equine breeding.

scholarly journals Experimental and Numerical Study of Fracture Behavior of Rock-Like Material Specimens with Single Pre-Set Joint under Dynamic Loading

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2690
Author(s):  
Bo Pan ◽  
Xuguang Wang ◽  
Zhenyang Xu ◽  
Lianjun Guo ◽  
Xuesong Wang
Keyword(s):  
Crack Initiation ◽  
Crack Propagation ◽  
Joint Angle ◽  
Simulation Software ◽  
Dissipated Energy ◽  
Energy Structure ◽  
Joint Angles ◽  
Crack Penetration ◽  
Before And After ◽  
The Impact

The Split Hopkinson Pressure Bar (SHPB) is an apparatus for testing the dynamic stress-strain response of the cement mortar specimen with pre-set joints at different angles to explore the influence of joint attitudes of underground rock engineering on the failure characteristics of rock mass structure. The nuclear magnetic resonance (NMR) has also been used to measure the pore distribution and internal cracks of the specimen before and after the testing. In combination with numerical analysis, the paper systematically discusses the influence of joint angles on the failure mode of rock-like materials from three aspects of energy dissipation, microscopic damage, and stress field characteristics. The result indicates that the impact energy structure of the SHPB is greatly affected by the pre-set joint angle of the specimen. With the joint angle increasing, the proportion of reflected energy moves in fluctuation, while the ratio of transmitted energy to dissipated energy varies from one to the other. NMR analysis reveals the structural variation of the pores in those cement specimens before and after the impact. Crack propagation direction is correlated with pre-set joint angles of the specimens. With the increase of the pre-set joint angles, the crack initiation angle decreases gradually. When the joint angles are around 30°–75°, the specimens develop obvious cracks. The crushing process of the specimens is simulated by LS-DYNA software. It is concluded that the stresses at the crack initiation time are concentrated between 20 and 40 MPa. The instantaneous stress curve first increases and then decreases with crack propagation, peaking at different times under various joint angles; but most of them occur when the crack penetration ratio reaches 80–90%. With the increment of joint angles in specimens through the simulation software, the changing trend of peak stress is consistent with the test results.

A Comparison of Fracture Mechanics and S–N Curve Approaches in Designing Drill Pipe

1992 ◽  
Vol 114 (3) ◽  
pp. 205-211 ◽  
Author(s):  
A. Ertas ◽  
G. Mustafa ◽  
O. Cuvalci
Keyword(s):  
Fracture Mechanics ◽  
Fatigue Damage ◽  
Drill Pipe ◽  
Ball Joint ◽  
Marine Riser ◽  
Deep Drilling ◽  
Miner’S Rule ◽  
Miner's Rule ◽  
Total Damage ◽  
Dynamic Fatigue

It is well known that the upper ball joint in a marine riser, in deep drilling, can cause fatigue damage in the drill pipe passing through it. A study of fracture mechanics and S–N curve approaches has been undertaken to determine the dynamic fatigue damage in the drill pipe. Miner’s rule is utilized in both methods to determine the total damage. The results of both methods are compared.

Marine Riser Monitoring With The Acoustic Ball Joint Angle-Azimuth Indicator

1971 ◽  
Author(s):  
Mark A. Childers ◽  
Gale A. Hazlewood ◽  
W.T. Lifrey
Keyword(s):  
Joint Angle ◽  
Ball Joint ◽  
Marine Riser

Gyroscope-Free Link Parameter Measurement Using Accelerometers and Magnetometer

2014 ◽  
Author(s):  
Vishesh Vikas ◽  
Carl D. Crane
Keyword(s):  
Angular Velocity ◽  
Joint Angle ◽  
Inertial Sensors ◽  
Angular Acceleration ◽  
Parameter Measurement ◽  
Joint Angles ◽  
Symmetry Constraint ◽  
Estimation Techniques ◽  
Angular Velocities ◽  
Joint Parameters

Knowledge of joint angles, angular velocities is essential for control of link mechanisms and robots. The estimation of joint angles and angular velocity is performed using combination of inertial sensors (accelerometers and gyroscopes) which are contactless and flexible at point of application. Different estimation techniques are used to fuse data from different inertial sensors. Bio-inspired sensors using symmetrically placed multiple inertial sensors are capable of instantaneously measuring joint parameters (joint angle, angular velocities and angular acceleration) without use of any estimation techniques. Calibration of inertial sensors is easier and more reliable for accelerometers as compared to gyroscopes. The research presents gyroscope-less, multiple accelerometer and magnetometer based sensors capable of measuring (not estimating) joint parameters. The contribution of the improved sensor are four-fold. Firstly, the inertial sensors are devoid of symmetry constraint unlike the previously researched bio-inspired sensors. However, the accelerometer are non-coplanarly placed. Secondly, the accelerometer-magnetometer combination sensor allows for calculation of a unique rotation matrix between two link joined by any kind of joint. Thirdly, the sensors are easier to calibrate as they consist only of accelerometers. Finally, the sensors allow for calculation of angular velocity and angular acceleration without use of gyroscopes.

scholarly journals A Workspace Visualization Method for a Multijoint Industrial Robot Based on the 3D-Printing Layering Concept

2020 ◽  
Vol 10 (15) ◽  
pp. 5241
Author(s):  
Guoqiang Fu ◽  
Chun Tao ◽  
Tengda Gu ◽  
Caijiang Lu ◽  
Hongli Gao ◽  
...  
Keyword(s):  
3D Printing ◽  
Joint Angle ◽  
Industrial Robot ◽  
Selection Method ◽  
Forward Kinematics ◽  
Visualization Method ◽  
Joint Angles ◽  
Boundary Extraction ◽  
Simulation And Experiment ◽  
Constraint Information

The workspace of a robot provides the necessary constraint information for path planning and reliable control of the robot. In this paper, a workspace visualization method for a multijoint industrial robot is proposed to obtain a detailed workspace by introducing the 3D-printing layering concept. Firstly, all possible joint-angle groups of one pose in the joints’ ranges are calculated in detail according to the POE (product of exponential) theory-based forward-kinematics expressions of the multijoint industrial robot. Secondly, a multisolution selection method based on the key degree of the joint is proposed to select the appropriate joint-angle groups. The key degrees of all joints and their key order are obtained according to the sensitivity expressions of all joint angles, calculated from the Jacobian matrix of the robot. One principle based on the smallest differences of the nominal angle is established to select the possible solutions for one joint from the possible solutions for the joint with the smaller key order. The possible solutions for the joint with the highest key order are the appropriate joint-angle group. Thirdly, a workspace visualization method based on the layering concept of 3D printing is presented to obtain a detailed workspace for a multijoint industrial robot. The boundary formula of each layer is derived by forward kinematics, which is expressed as a circle or a ring. The maximum and minimum values of the radius are obtained according to the travel range of the joint angles. The height limitations of all layers are obtained with forward kinematics. A workspace boundary-extraction method is presented to obtain the array of path points of the boundary at each layer. The proposed postprocessing method is used to generate the joint-angle code of each layer for direct 3D printing. Finally, the effectiveness of the multisolution selection method and the workspace visualization method were verified by simulation and experiment.

scholarly journals Estimation of Continuous Joint Angles of Upper Limb Based on sEMG by Using GA-Elman Neural Network

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Junhong Wang ◽  
Qiqi Hao ◽  
Xugang Xi ◽  
Jiuwen Cao ◽  
Anke Xue ◽  
...  
Keyword(s):  
Neural Network ◽  
Genetic Algorithm ◽  
Elbow Joint ◽  
Joint Angle ◽  
Wavelet Packet ◽  
Upper Limbs ◽  
Joint Angles ◽  
Semg Signal ◽  
Elman Neural Network ◽  
Shoulder Movement

The estimation of continuous and simultaneous multijoint angle based on surface electromyography (sEMG) signal is of considerable significance in rehabilitation practice. However, there are few studies on the continuous joint angle of multiple joints at present. In this paper, the wavelet packet energy entropy (WPEE) of the special subspace was investigated as a feature of the sEMG signal. An Elman neural network optimized by genetic algorithm (GA) was established to estimate the joint angle of shoulder and elbow. First, the accuracy of the method is verified by estimating the angle of the shoulder joint. Then, this method was used to simultaneously and continuously estimate the shoulder and elbow joint angle. Six subjects flexed and extended the upper limbs according to the intended movements of the experiment. The results show that this method can obtain a decent performance with a RMSE of 3.4717 and R2 of 0.8283 in shoulder movement and with a RMSE of 4.1582 and R2 of 0.8114 in continuous synchronous movement of the shoulder and elbow.

Analysis of the mero-carpopodite joint of the American lobster and snow crab. II. Kinematics, morphometrics and moment arms

2003 ◽  
Vol 83 (6) ◽  
pp. 1249-1259 ◽  
Author(s):  
S.C. Mitchell ◽  
M.E. DeMont
Keyword(s):  
Joint Angle ◽  
Snow Crab ◽  
Moment Arm ◽  
Scaling Effects ◽  
Joint Angles ◽  
Positive Allometry ◽  
Moment Arms ◽  
Arm Reaching ◽  
Flexion Extension ◽  
The Moment

This research reports on the kinematics of lobster and snow crab walking, documents changes in the moment arms of the mero-carpopodite joint during rotation, and examines scaling effects of morphological and mechanical variables in these crustacean species. Forward walking lobsters and lateral walking crabs were recorded and images analysed to describe the kinematics of these animals, and subsequently morphometric and moment arm measurements made. During forward walking the lobster maintains fixed mero-carpopodite joint angles during both the power and recovery strokes, though each of the walking legs maintains different joint angles. Legs 3 and 5 are maintained at angles which appear to equalize the flexor and extensor moment arms, and leg 4 joint angle appears to maximize the extensor moment arm. The snow crab has a joint excursion angle of between approximately 50° to 150° and, during flat bed walking, the leading and trailing legs move through similar excursion angles. The length of the meropodite for both species are longer for the anterior two leg pairs relative to the posterior two pairs and the rate of growth of the meropodite is largely isometric for the lobster while consistently increases with positive allometry in the crab. The flexor and extensor moment arms generated as the joint undergoes flexion/extension show two distinct patterns with the extensor moment arm being maximized at relatively low joint angles (55°–115°) and the flexor moment arm reaching a plateau at joint extension with angles between 95° and 155°. The flexor apodeme possesses the largest moment arms in all legs for both species, suggesting the flexors are able to generate greater torques. It appears that, mechanically, these laterally moving animals may be ‘pulling’ with the leading legs to a greater extent than ‘pushing’ with the trailing legs.

Minimizing Casing Wear in Dog Legs

1977 ◽  
Vol 99 (1) ◽  
pp. 215-223 ◽  
Author(s):  
W. B. Bradley
Keyword(s):  
Drill Pipe ◽  
Field Measurements ◽  
Experimental Information ◽  
Wear Performance ◽  
Wear Rates ◽  
Casing Wear

Procedures are presented for estimating the amount of casing wear produced in wells by the rotation of tool joints, drill pipe, and drill pipe protectors against casing. The procedures are based upon experimental information and limited field measurements developed over a period of several years [1–5]. The procedures have been used with moderate success in predicting the casing wear rates seen in the field for a limited number of cases. The paper again emphasizes that with the proper use of drill pipe protectors casing wear can be minimized. In addition, the paper presents suggested procedures for selecting drill pipe protectors to assure consistent casing wear performance.

Sign in / Sign up

Export Citation Format

Share Document