Fatigue Crack Growth of Duplex Stainless Steel Castings at 4 K

1985 ◽  
Vol 107 (2) ◽  
pp. 161-165 ◽  
Author(s):  
P. T. Purtscher ◽  
Y. W. Cheng ◽  
P. N. Li
Keyword(s):  
Stainless Steel ◽  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Duplex Stainless Steel ◽  
Crack Growth ◽  
Growth Rates ◽  
Constant Load ◽  
Steel Castings ◽  
Constant Load Amplitude ◽  
Crack Growth Rates

Constant-load-amplitude stage II fatigue crack growth rates at 4 K were measured for duplex stainless steel castings. The results show that at a ΔK of 60 MPa•m1/2, da/dN = 7.6 × 10−4 mm/cycle for an alloy with 1 percent ferrite. For an alloy with 8 percent ferrite, da/dN is 35 percent, and for an alloy with 29 percent ferrite, da/dN is 260 percent greater than for the 1 percent ferrite alloy. However, the exponent in the Paris equation does not change appreciably (less than 18 percent) as the ferrite content changes from 1 to 29 percent.

Fatigue Crack Growth in Type 316 Stainless Steel at High Temperature

1971 ◽  
Vol 93 (4) ◽  
pp. 976-980 ◽  
Author(s):  
P. Shahinian ◽  
H. H. Smith ◽  
H. E. Watson
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Growth Rates ◽  
316 Stainless Steel ◽  
Arrhenius Relation ◽  
Crack Growth Rates

The dependence of fatigue crack growth rates on range of stress intensity factor (ΔK) in Type 316 stainless steel was investigated over the temperature range of 75 to 1100 deg F. The data for the most part could be described by a power law relationship. An increase in temperature generally increased crack growth rate for a given ΔK and decreased fatigue life. The dependence of crack growth rate on temperature is not described adequately by an Arrhenius relation over the range investigated. On the other hand, by normalizing ΔK with respect to Young’s modulus, E, the crack growth rates for the various temperatures tend to fall within a single band.

scholarly journals Advantageous Description of Short Fatigue Crack Growth Rates in Austenitic Stainless Steels with Distinct Properties

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 475
Author(s):  
Lukáš Trávníček ◽  
Ivo Kuběna ◽  
Veronika Mazánová ◽  
Tomáš Vojtek ◽  
Jaroslav Polák ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Stainless Steels ◽  
Growth Rates ◽  
Large Scale ◽  
J Integral ◽  
Scale Yielding ◽  
Residual Fatigue ◽  
Crack Growth Rates

In this work two approaches to the description of short fatigue crack growth rate under large-scale yielding condition were comprehensively tested: (i) plastic component of the J-integral and (ii) Polák model of crack propagation. The ability to predict residual fatigue life of bodies with short initial cracks was studied for stainless steels Sanicro 25 and 304L. Despite their coarse microstructure and very different cyclic stress–strain response, the employed continuum mechanics models were found to give satisfactory results. Finite element modeling was used to determine the J-integrals and to simulate the evolution of crack front shapes, which corresponded to the real cracks observed on the fracture surfaces of the specimens. Residual fatigue lives estimated by these models were in good agreement with the number of cycles to failure of individual test specimens strained at various total strain amplitudes. Moreover, the crack growth rates of both investigated materials fell onto the same curve that was previously obtained for other steels with different properties. Such a “master curve” was achieved using the plastic part of J-integral and it has the potential of being an advantageous tool to model the fatigue crack propagation under large-scale yielding regime without a need of any additional experimental data.

Sign in / Sign up

Export Citation Format

Share Document