Reduction of Free-Edge Stress Concentration

1985 ◽  
Vol 52 (4) ◽  
pp. 801-805 ◽  
Author(s):  
P. R. Heyliger ◽  
J. N. Reddy
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Free Edge ◽  
Shear Stresses ◽  
Normal Stresses ◽  
Interlaminar Shear ◽  
Three Dimensional Elasticity

A quasi-three dimensional elasticity formulation and associated finite element model for the stress analysis of symmetric laminates with free-edge cap reinforcement are described. Numerical results are presented to show the effect of the reinforcement on the reduction of free-edge stresses. It is observed that the interlaminar normal stresses are reduced considerably more than the interlaminar shear stresses due to the free-edge reinforcement.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

scholarly journals Numerical investigation of plastic flow and residual stresses generated in hydroformed tubes

2021 ◽  
pp. 146442072198974
Author(s):  
A Ktari ◽  
A Abdelkefi ◽  
N Guermazi ◽  
P Malecot ◽  
N Boudeau
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Plastic Flow ◽  
Tube Hydroforming ◽  
Three Dimensional ◽  
Element Model ◽  
Tube Cross Section ◽  
Straight Wall ◽  
Hydroforming Process

During tube hydroforming process, the friction conditions between the tube and the die have a great importance on the material plastic flow and the distribution of residual stresses of the final component. Indeed, a three-dimensional finite element model of a tube hydroforming process in the case of square section die has been performed, using dynamic and static approaches, to study the effect of the friction conditions on both plastic flow and residual stresses induced by the process. First, a comparative study between numerical and experimental results has been carried out to validate the finite element model. After that, various coefficients of friction were considered to study their effect on the thinning phenomenon and the residual stresses distribution. Different points have been retained from this study. The thinning is located in the transition zone cited between the straight wall and the corner zones of hydroformed tube due to the die–tube contact conditions changes during the process. In addition, it is clear that both die–tube friction conditions and the tube bending effects, which occurs respectively in the tube straight wall and corner zones, are the principal causes of the obtained residual stresses distribution along the tube cross-section.

scholarly journals MODELLING FROM THE PAST: THE LEANING SOUTWEST TOWER OF CAERPHILLY CASTLE 1539-2015

2017 ◽  
Vol IV-2/W2 ◽  
pp. 221-227 ◽  
Author(s):  
O. E. C. Prizeman ◽  
V. Sarhosis ◽  
A. M. D’Alri ◽  
C. J. Whitman ◽  
G. Muratore
Keyword(s):  
Finite Element ◽  
Structural Analysis ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Present Condition ◽  
Long Term Stability ◽  
Dimensional Finite Element ◽  
The Uk ◽  
Three Dimensional Finite Element

Caerphilly Castle (1268-70) is the first concentric castle in Britain and the second largest in the UK. The dramatic inclination of its ruinous south west tower has been noted since 1539. Comparing data from historical surveys and a terrestrial laser scan undertaken in 2015, this paper seeks to review evidence for the long-term stability of the tower. Digital documentation and archival research by architects is collated to provide data for structural analysis by engineers. A terrestrial laser scan was used to create a detailed three dimensional finite element model to enable structural analysis of the current shape of the tower made by tetrahedral elements. An automated strategy has been implemented for the transformation of the complex three dimensional point cloud into a three dimensional finite element model. Numerical analysis has been carried out aiming at understanding the main structural weaknesses of the tower in its present condition. Comparisons of four sets of data: 1539, 1830, 1870 and 2015 enabled us to determine change albeit between very different methods of measurement.

Sign in / Sign up

Export Citation Format

Share Document