Notch-Tip Stresses in a Creeping Solid

1984 ◽  
Vol 51 (3) ◽  
pp. 475-480 ◽  
Author(s):  
J. L. Bassani
Keyword(s):  
Strain Rate ◽  
Power Law ◽  
High Stress ◽  
Shear Loading ◽  
Antiplane Shear ◽  
Sharp Notch ◽  
Hyperbolic Sine ◽  
Notch Tip ◽  
As Stress ◽  
Sine Law

At high stress levels the creep strain rate for many materials varies as the exponential of stress while at low stresses it varies as stress to some power. An analysis is presented for a sharp notch under antiplane shear loading in a material that deforms by hyperbolic-sine-law creep, ε˙c = ε˙0[sinh(σ/σ0)]n. The asymptotic notch-tip stress intensification is weaker and the strain-rate intensification is stronger than for a power-law creeping material.

Correspondence Relations for the Interface Crack in Monoclinic Composites Under Mixed Loading

1990 ◽  
Vol 57 (4) ◽  
pp. 894-900 ◽  
Author(s):  
Kuang-Chong Wu ◽  
Shyh-Jye Hwang
Keyword(s):  
Interface Crack ◽  
Crack Problem ◽  
Shear Loading ◽  
Antiplane Shear ◽  
Intensity Factors ◽  
Plane Shear ◽  
Applied Loading ◽  
As Stress ◽  
Crack Faces ◽  
Quantities Of Interest

A correspondence is established between the problem of an interface crack in mon-oclinic composites and that of an interface crack in isotropic composites. The interface crack considered is subjected to a combined tension-compression, in-plane shear and antiplane shear loading at the crack faces. Under the applied loading, the interface crack is assumed to be partially opened. Through the correspondence, quantities of interest such as stress intensity factors, sizes of the contact zones, for monoclinic composites can be obtained from the results of the isotropic interface crack problem.

Singular stresses at the tip of a sharp notch in power-law-hardening materials under antisymmetric loading

1996 ◽  
Vol 31 (6) ◽  
pp. 693-701 ◽  
Author(s):  
N. V. Kouzniak ◽  
H. P. Rossmanith ◽  
M. P. Savruk
Keyword(s):  
Power Law ◽  
Sharp Notch ◽  
Antisymmetric Loading

Applicability of power law for describing the rheology of soils of different origins and characteristics

2009 ◽  
Vol 46 (9) ◽  
pp. 1011-1023 ◽  
Author(s):  
Sueng Won Jeong ◽  
Serge Leroueil ◽  
Jacques Locat
Keyword(s):  
Strain Rate ◽  
Power Law ◽  
Debris Flows ◽  
Rheological Behaviour ◽  
Strain Rate Range ◽  
Rate Dependent ◽  
Different Origins ◽  
Power Law Index ◽  
Soil Behaviour ◽  
Low Activity

The rate-dependent rheological behaviour of soils of different origins and characteristics was studied and the applicability of the power law model was examined. The studied soils were divided into three groups: (i) low-activity soils, (ii) high-activity soils, and (iii) silt-rich soils. The results show that the power law applies to all these soils and is representative of soil behaviour in a strain rate range corresponding to debris flows, which is generally not the case with the Bingham model. For low-activity clays, the power law index, n, is typically equal to 0.12 and seems to increase with the plasticity index; it is larger (i.e., in the range of 0.2–0.6) for silt-rich soils. Comparison of n values for tests performed on intact and remoulded low-activity clay specimens indicates that the power law index is possibly strain-rate dependent.

Simulation of Influence of Friction Coefficient on Extrusion of TC4 Alloy

2013 ◽  
Vol 470 ◽  
pp. 244-249
Author(s):  
Chang Dong Liu ◽  
Yi Du Zhang
Keyword(s):  
Friction Coefficient ◽  
Strain Rate ◽  
Effective Strain ◽  
High Stress ◽  
Extrusion Process ◽  
Extrusion Pressure ◽  
Tc4 Alloy ◽  
Stress Zone ◽  
D Model ◽  
High Stress Zone

Based on Simufact11.0, a 3-D model of T profile extrusion is established and the extrusion process of TC4 is investigated using finite volumemethod(FVM) of Euler mesh description. Effects of different friction coefficients on the effective stress, extrusion pressure, effective strain and effective strain rate have been studied. The study shows that there is a high-stress zone at a certain distance from the entrance of the forming area and a high strain rate zone around that area. With the increase of friction coefficient, the value of the stress increased and the deformation is more uneven. The track of extrusion pressure shows that extrusion increase with the increase of friction coefficient.

Investigation of PDC Cutter Interface Geometry Using 3D FEM Modelling

2017 ◽  
Vol 29 ◽  
pp. 45-53 ◽  
Author(s):  
Seyed Ali Heydarshahy ◽  
Shivakumar Karekal
Keyword(s):  
Strain Distribution ◽  
High Stress ◽  
Polycrystalline Diamond ◽  
Shear Loading ◽  
Stress And Strain ◽  
3D Fem ◽  
Interface Shear ◽  
Interface Elements ◽  
Premature Failure ◽  
Stress And Strain Distribution

Polycrystalline Diamond Compact (PDC) cutters have been popularly used in recent times due to their resistance against mechanical and thermal wear. This paper was focused on interface geometries between the substrate and the diamond table. Various types of interfaces were designed, to investigate how different interface geometries influence distribution of stress and strain under shear loading. The interface geometries examined in this paper included castle interface, dent interface, honeycomb interface and chase interface. Parallel to the interface, shear loading was applied to the top of diamond table to mimic the shear loading component from the rock cutting. To apply the shear loading, two locations were considered for each of the geometries. These locations differed depending on the interface features. Stress and strain distribution and values across different interface geometries were analysed with the aid of 3D Finite Element Method (FEM). The numerical simulations indicated that stress and strain magnitudes and distribution patterns varied in relation to different geometries. Some substrates showed relatively lower plastic strain representing higher durability of the geometries. Concentration of stress and strain distribution showed the areas where one could expect weakness. It also implies that rotating the PDC cutter assemblies around their cylindrical axis helps avoiding fatigue of interface elements in regions of high stress concentration; and thus, preventing premature failure of interface elements.

Strength and deformation of frozen saturated sand at −30 °C

1982 ◽  
Vol 19 (1) ◽  
pp. 104-107 ◽  
Author(s):  
V. R. Parameswaran ◽  
M. Roy
Keyword(s):  
Strain Rate ◽  
Power Law ◽  
Quartz Sand ◽  
Peak Strength ◽  
Strain Rates ◽  
Saturated Sand ◽  
Ideal Plastic ◽  
Strength And Deformation ◽  
Power Law Equation

Frozen saturated quartz sand containing 20% moisture by weight, when deformed at −30 °C at various strain rates, showed various modes of behaviour such as visco-plastic, almost ideal plastic, and brittle with little plasticity with increasing order of strain rate. The values of peak strength observed for strain rates between 5 × 10−7 and 6 × 10−3 s−1 were in the range 15–42 MPa, stress being related to strain rate by a power-law equation.

scholarly journals Strain rate and thermal softening effects in shear testing of AA7075-T6 sheet

2018 ◽  
Vol 183 ◽  
pp. 02037 ◽  
Author(s):  
Taamjeed Rahmaan ◽  
Ping Zhou ◽  
Cliff Butcher ◽  
Michael J. Worswick
Keyword(s):  
Strain Rate ◽  
High Speed ◽  
Rate Sensitivity ◽  
Thermal Conditions ◽  
Shear Loading ◽  
Image Correlation ◽  
High Rate ◽  
Strain Rates ◽  
Shear Testing ◽  
Plane Shear

Shear tests were performed at strain rates ranging from quasi-static (0.01 s-1) to 500 s-1 for AA7075-T6 sheet metal alloy at room temperature. A miniature sized shear specimen was used in this work to perform high strain rate shear testing. Digital image correlation (DIC) techniques were employed to measure the strains in the experiments. At maximum in-plane shear strains greater than 20%, the AA7075-T6 alloy demonstrated a reduced work hardening rate at elevated strain rates. At lower strains, the AA7075-T6 alloy showed mild positive rate sensitivity. The strain to localization (using the Zener-Holloman criterion), measured using the DIC technique, decreased with strain rate in shear loading. The strain at complete failure, however, exhibited an increase at the highest strain rate (500 s-1). The current work also focused on characterization of the thermal conditions occurring during high rate loading in shear with in situ high speed thermal imaging. Experimental results from the highest strain rate (500 s-1) tests showed a notable increase in temperature within the specimen gauge region as a result of the conversion of plastic deformation energy into heat.

Sign in / Sign up

Export Citation Format

Share Document