Fault Growth and Acoustic Emissions in Confined Granite

1992 ◽  
Vol 45 (3S) ◽  
pp. S165-S173 ◽  
Author(s):  
David A. Lockner ◽  
James D. Byerlee
Keyword(s):  
Acoustic Emission ◽  
Fault Plane ◽  
Process Zone ◽  
Failure Process ◽  
Acoustic Emissions ◽  
Strain Curve ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Fracture Front ◽  
Fault Growth

The failure process in a brittle granite was studied by using acoustic emission techniques to obtain three dimensional locations of the microfracturing events. During a creep experiment the nucleation of faulting coincided with the onset of tertiary creep, but the development of the fault could not be followed because the failure occurred catastrophically. A technique has been developed that enables the failure process to be stabilized by controlling the axial stress to maintain a constant acoustic emission rate. As a result the post-failure stress-strain curve has been followed quasi-statically, extending to hours the fault growth process that normally would occur violently in a fraction of a second. The results from the rate-controlled experiments show that the fault plane nucleated at a point on the sample surface after the stress-strain curve reached its peak. Before nucleation, the microcrack growth was distributed throughout the sample. The fault plane then grew outward from the nucleation site and was accompanied by a gradual drop in stress. Acoustic emission locations showed that the fault propagated as a fracture front (process zone) with dimensions of 1 to 3 cm. As the fracture front passed by a given fixed point on the fault plane, the subsequent acoustic emission would drop. When growth was allowed to progress until the fault bisected the sample, the stress dropped to the frictional strength. These observations are in accord with the behavior predicted by Rudnicki and Rice’s bifurcation analysis but conflict with experiments used to infer that shear localization would occur in brittle rock while the material is still hardening.

scholarly journals Proposed Constitutive Law of Uniaxial Compression for Concrete under Deterioration Effects

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2048 ◽  
Author(s):  
Yiwei Gao ◽  
Xuhua Ren ◽  
Jixun Zhang ◽  
Lingwei Zhong ◽  
Shuyang Yu ◽  
...  
Keyword(s):  
Uniaxial Compression ◽  
Failure Process ◽  
Strain Curve ◽  
Ductile Deformation ◽  
Deformation Capacity ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
New Model ◽  
Freeze Thaw ◽  
Prediction Curve

In order to study the ductile deformation characteristics and failure process of plain concrete under uniaxial compression, this paper proposes a new constitutive model. The new model was used to fit and analyze the constitutive curve of concrete under uniaxial compressive under various degradation forms and was compared with the traditional constitutive models. Finally, the new model was used to quantitatively analyze and predict the stress–strain curve of concrete in different degradation periods of a set of freeze–thaw measured data. The results show that, compared with the traditional constitutive model, the new model is simple in form and has few parameters, and the numerical value of the parameter can reflect the ductile deformation capacity of concrete. The fitting curve of the new model has the highest fitting degree with the measured stress–strain curve of concrete, and the goodness of fit (R2) is also the largest. The new model is suitable for fitting the stress–strain curve of concrete under uniaxial compression under various deteriorating forms, and the degree of fit between the constitutive prediction curve and the measured curve is high. It can be seen from the fitting results of the new model parameters that the ductile deformation capacity of concrete decreases first and then increases slightly, which is inconsistent with the law of gradual deterioration of strength. There is a minimum moment of ductility deformation capacity of concrete (MDC). The MDC of O-C40 concrete is about 114 freeze–thaw cycles, and the MDC of O-C50 concrete is about 116 freeze–thaw cycles; the degree of fit between the constitutive prediction curve and the measured curve is high. We hope that the improvement mentioned offers valid reference to the study of ductile deformation characteristics and failure process of compressed concrete under different deterioration forms.

Failure Process and Stress-Strain Curve of Plane Strain Rock Specimen with Initially Random Material Imperfections

2007 ◽  
Vol 353-358 ◽  
pp. 1133-1136 ◽  
Author(s):  
X.B. Wang
Keyword(s):  
Rock Specimen ◽  
Failure Process ◽  
Shear Bands ◽  
Strain Curve ◽  
Peak Stress ◽  
Plastic Behavior ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Initial Imperfections ◽  
Ideal Plastic

The failure process of heterogeneous rock specimen with initially random material imperfections in uniaxial plane strain compression and the macroscopically mechanical response are numerically modeled by using FLAC (Fast Lagrangian Analysis of Continua). A FISH function is generated to prescribe the initial imperfections within the heterogeneous specimen by using Matlab. The imperfection is weaker than the intact rock. Beyond the failure of the imperfection, it undergoes ideal plastic behavior, while intact rock exhibits linear strain-softening behavior and then ideal plastic behavior once failure occurs. The specimen with smooth ends is loaded at a constant strain rate and is divided into 3200 elements. The maximum numbers of the initial imperfections in five schemes are 100, 300, 500, 700 and 900. The effects of the number of the imperfections on the fracture process, the final fracture pattern and the complete stress-strain curve are investigated. Prior to the peak stress, some imperfections extend in the axial direction and then a part of them coalesce to form inclined shear bands. Beyond the peak stress, shear bands progressively intersect the specimen; in the process the number of the yielded elements approximately remains a constant. With an increase of the number of the initial imperfections, the spacing of shear fractures decreases, the peak stress and corresponding axial strain decrease; the post-peak branch of stress-strain curve becomes steeper; much more elements fail in tension; the number of the yielded elements in tension in the vicinity of the two lateral edges of the specimen remarkably increases.

A modified version of MATLAB application window for predicting the weld bead profile and stress–strain plot of AA5052 CMT weldment using ER4043

SIMULATION ◽  
2021 ◽  
pp. 003754972110315
Author(s):  
B Girinath ◽  
N Siva Shanmugam
Keyword(s):  
Strain Curve ◽  
Weld Bead ◽  
Welding Parameters ◽  
Bead Geometry ◽  
Hybrid Technique ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Weld Bead Geometry ◽  
Inference System ◽  
Engineering Stress

The present study deals with the extended version of our previous research work. In this article, for predicting the entire weld bead geometry and engineering stress–strain curve of the cold metal transfer (CMT) weldment, a MATLAB based application window (second version) is developed with certain modifications. In the first version, for predicting the entire weld bead geometry, apart from weld bead characteristics, x and y coordinates (24 from each) of the extracted points are considered. Finally, in the first version, 53 output values (five for weld bead characteristics and 48 for x and y coordinates) are predicted using both multiple regression analysis (MRA) and adaptive neuro fuzzy inference system (ANFIS) technique to get an idea related to the complete weld bead geometry without performing the actual welding process. The obtained weld bead shapes using both the techniques are compared with the experimentally obtained bead shapes. Based on the results obtained from the first version and the knowledge acquired from literature, the complete shape of weld bead obtained using ANFIS is in good agreement with the experimentally obtained weld bead shape. This motivated us to adopt a hybrid technique known as ANFIS (combined artificial neural network and fuzzy features) alone in this paper for predicting the weld bead shape and engineering stress–strain curve of the welded joint. In the present study, an attempt is made to evaluate the accuracy of the prediction when the number of trials is reduced to half and increasing the number of data points from the macrograph to twice. Complete weld bead geometry and the engineering stress–strain curves were predicted against the input welding parameters (welding current and welding speed), fed by the user in the MATLAB application window. Finally, the entire weld bead geometries were predicted by both the first and the second version are compared and validated with the experimentally obtained weld bead shapes. The similar procedure was followed for predicting the engineering stress–strain curve to compare with experimental outcomes.

Stress-strain curve of paper revisited

2012 ◽  
Vol 27 (2) ◽  
pp. 318-328 ◽  
Author(s):  
Svetlana Borodulina ◽  
Artem Kulachenko ◽  
Mikael Nygårds ◽  
Sylvain Galland
Keyword(s):  
Three Dimensional ◽  
Strain Curve ◽  
Failure Behavior ◽  
Three Dimensional Model ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Fiber Network ◽  
Bonding Parameters ◽  
Particle Level ◽  
The Impact

Abstract We have investigated a relation between micromechanical processes and the stress-strain curve of a dry fiber network during tensile loading. By using a detailed particle-level simulation tool we investigate, among other things, the impact of “non-traditional” bonding parameters, such as compliance of bonding regions, work of separation and the actual number of effective bonds. This is probably the first three-dimensional model which is capable of simulating the fracture process of paper accounting for nonlinearities at the fiber level and bond failures. The failure behavior of the network considered in the study could be changed significantly by relatively small changes in bond strength, as compared to the scatter in bonding data found in the literature. We have identified that compliance of the bonding regions has a significant impact on network strength. By comparing networks with weak and strong bonds, we concluded that large local strains are the precursors of bond failures and not the other way around.

Definition of the yield point in plasticity and its effect on the shape of the yield locus

1966 ◽  
Vol 1 (4) ◽  
pp. 331-338 ◽  
Author(s):  
T C Hsu
Keyword(s):  
Yield Point ◽  
Experimental Work ◽  
Strain Curve ◽  
Yield Locus ◽  
Experimental Results ◽  
Stress Strain Curve ◽  
Proportional Limit ◽  
Stress Strain ◽  
Small Section ◽  
Definition Of

Three different definitions of the yield point have been used in experimental work on the yield locus: proportional limit, proof strain and the ‘yield point’ by backward extrapolation. The theoretical implications of the ‘yield point’ by backward extrapolation are examined in an analysis of the loading and re-loading stress paths. It is shown, in connection with experimental results by Miastkowski and Szczepinski, that the proportional limit found by inspection is in fact a point located by backward extrapolation based on a small section of the stress-strain curve, near the elastic portion of the curve. The effect of different definitions of the yield point on the shape of the yield locus and some considerations for the choice between them are discussed.

Identification of post-necking stress–strain curve for sheet metals by inverse method

2016 ◽  
Vol 92 ◽  
pp. 107-118 ◽  
Author(s):  
Kunmin Zhao ◽  
Limin Wang ◽  
Ying Chang ◽  
Jianwen Yan
Keyword(s):  
Inverse Method ◽  
Strain Curve ◽  
Sheet Metals ◽  
Stress Strain Curve ◽  
Stress Strain

Behavior and modeling of post-heated circular concrete specimens repaired with fiber-reinforced polymer composites

2021 ◽  
pp. 136943322110585
Author(s):  
Seyed Mehrdad Elhamnike ◽  
Rasoul Abbaszadeh ◽  
Vahid Razavinasab ◽  
Hadi Ziaadiny
Keyword(s):  
Strain Curve ◽  
Concrete Columns ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Concrete Members ◽  
Frp Composites ◽  
Reinforced Polymer ◽  
Fiber Reinforced Polymer Composites

Exposure of buildings to fire is one of the unexpected events during the life of the structure. The heat from the fire can reduce the strength of structural members, and these damaged members need to be strengthened. Repair and strengthening of concrete members by fiber-reinforced polymer (FRP) composites has been one of the most popular methods in recent years and can be used in fire-damaged concrete members. In this paper, in order to provide further data and information about the behavior of post-heated circular concrete columns confined with FRP composites, 30 cylindrical concrete specimens were prepared and subjected under four exposure temperatures of 300, 500, 700, and 900. Then, specimens were repaired by carbon fiber reinforced polymer composites and tested under axial compression. Results indicate that heating causes the color change, cracks, and weight loss of concrete. Also, with the increase of heating temperature, the shape of stress–strain curve of FRP-retrofitted specimens will change. Therefore, the main parts of the stress–strain curve such as ultimate stress and strain and the elastic modulus will change. Thus, a new stress–strain model is proposed for post-heated circular concrete columns confined by FRP composites. Results indicate that the proposed model is in a good agreement with the experimental data.

Sign in / Sign up

Export Citation Format

Share Document