Turbulence Structure Modification and Drag Reduction by Microbubble Injections in a Boundary Layer Channel Flow

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
C. C. Gutiérrez-Torres ◽  
Y. A. Hassan ◽  
J. A. Jimenez-Bernal
Keyword(s):  
Boundary Layer ◽  
Drag Reduction ◽  
Channel Flow ◽  
Single Phase ◽  
Pure Water ◽  
Channel Height ◽  
Turbulence Structure ◽  
Two Phase ◽  
Flow Measurements ◽  
Phase Water

Turbulent boundary layer modification in a channel flow using injection of microbubbles as a means to achieve drag reduction was studied. The physical mechanism of this phenomenon is not yet fully understood. To obtain some information related to this phenomenon, single-phase (pure water) flow and two-phase (water and microbubbles) channel flow measurements are taken. The void fraction conditions were varied while maintaining a Reynolds number of 5128 based on the half channel height. The study indicates that the presence of microbubbles within the boundary layer modifies the turbulence structure such that variations in time and space turbulent scales are observed, as well as ejection and sweep phenomena.

Two-Phase Flow in Microchannels

2001 ◽  
Author(s):  
G. Hetsroni ◽  
A. Mosyak ◽  
Z. Segal
Keyword(s):  
Heat Sink ◽  
High Speed ◽  
Single Phase ◽  
Flow Boiling ◽  
Electronics Cooling ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Infrared Radiometry ◽  
Phase Water

Abstract Experimental investigation of a heat sink for electronics cooling is performed. The objective is to keep the operating temperature at a relatively low level of about 323–333K, while reducing the undesired temperature variation in both the streamwise and transverse directions. The experimental study is based on systematic temperature, flow and pressure measurements, infrared radiometry and high-speed digital video imaging. The heat sink has parallel triangular microchannels with a base of 250μm. According to the objectives of the present study, Vertrel XF is chosen as the working fluid. Experiments on flow boiling of Vertrel XF in the microchannel heat sink are performed to study the effect of mass velocity and vapor quality on the heat transfer, as well as to compare the two-phase results to a single-phase water flow.

scholarly journals Heat transfer and entropy generation in a microchannel with longitudinal vortex generators using Nanofluids

2020 ◽  
Author(s):  
Amin Ebrahimi ◽  
Farhad Rikhtegar Nezami ◽  
Amin Sabaghan ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Single Phase ◽  
Pure Water ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Working Fluid ◽  
Two Phase ◽  
Rectangular Microchannel ◽  
Important Conclusion

Conjugated heat transfer and hydraulic performance for nanofluid flow in a rectangular microchannel heat sink with LVGs (longitudinal vortex generators) are numerically investigated using at different ranges of Reynolds numbers. Three-dimensional simulations are performed on a microchannel heated by a constant heat flux with a hydraulic diameter of 160 μm and six pairs of LVGs using a single-phase model. Coolants are selected to be nanofluids containing low volume-fractions (0.5%–3.0%) of Al2O3 or CuO nanoparticles with different particle sizes dispersed in pure water. The employed model is validated and compared by published experimental, and single-phase and two-phase numerical data for various geometries and nanoparticle sizes. The results demonstrate that heat transfer is enhanced by 2.29–30.63% and 9.44%–53.06% for water-Al2O3 and water-CuO nanofluids, respectively, in expense of increasing the pressure drop with respect to pure-water by 3.49%–16.85% and 6.5%–17.70%, respectively. We have also observed that the overall efficiency is improved by 2.55%–29.05% and 9.78%–50.64% for water-Al2O3 and water-CuO nanofluids, respectively. The results are also analyzed in terms of entropy generation, leading to the important conclusion that using nanofluids as the working fluid could reduce the irreversibility level in the rectangular microchannel heat sinks with LVGs. No exterma (minimums) is found for total entropy generation for the ranges of parameters studied.

Sign in / Sign up

Export Citation Format

Share Document