Adiabatic Horizontal and Vertical Pressure Drop of Carbon Dioxide Inside Smooth and Microfin Tubes at Low Temperatures

2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Yoon Jo Kim ◽  
Jeremy Jang ◽  
Predrag S. Hrnjak ◽  
Min Soo Kim
Keyword(s):  
Pressure Drop ◽  
Mass Flux ◽  
Two Phase Flow ◽  
Interfacial Shear Stress ◽  
Smooth Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Vertical Pressure ◽  
Frictional Pressure Drop ◽  
Microfin Tubes

This paper presents the pressure drop data and the analysis of adiabatic CO2 flow in horizontal and vertical smooth and microfin tubes at saturation temperatures around −20°C. The test tubes had 3.48mm inner diameter smooth tube and a 3.51mm melt-down diameter microfin tube. The test was performed over a mass flux range of 200–800kg∕m2s and at saturation temperatures of −25°C and −15°C. The effects of various parameters—mass flux, saturated temperature, and tube diameter—on pressure drop were qualitatively analyzed. The analyses showed that the frictional pressure drop characteristics of vertical two-phase flow were much different from that of the horizontal two-phase flow. The microfin tube can be considered as “very rough tube” having the roughness of “fin height.” The data were compared with several correlations. The existing frictional pressure drop correlation is sufficient to predict the horizontal pressure drop in smooth tube. For the vertical pressure drop, the simple combination of the frictional pressure drop and void fraction model was in comparatively good agreement. However, the qualitative results showed that there were some limits to cover the different mechanisms related to the interfacial shear stress. The average enhancement factors and penalty factors evidenced that it was not always true that the internally finned geometry guaranteed the superior in-tube condensation performance of microfin tube in refrigeration system and air-conditioning systems.

Evaluation Analysis of Prediction Methods for Two-Phase Flow Pressure Drop in Mini-Channels

2008 ◽  
Author(s):  
Licheng Sun ◽  
Kaichiro Mishima
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Turbulent Region ◽  
Frictional Pressure Drop ◽  
New Correlation ◽  
Mini Channels ◽  
Flow Pressure ◽  
Better Than

2092 data of two-phase flow pressure drop were collected from 18 published papers of which the working fluids include R123, R134a, R22, R236ea, R245fa, R404a, R407C, R410a, R507, CO2, water and air. The hydraulic diameter ranges from 0.506 to 12mm; Relo from 10 to 37000, and Rego from 3 to 4×105. 11 correlations and models for calculating the two-phase frictional pressure drop were evaluated based upon these data. The results show that the accuracy of the Lockhart-Martinelli method, Mishima and Hibiki correlation, Zhang and Mishima correlation and Lee and Mudawar correalion in the laminar region is very close to each other, while the Muller-Steinhagen and Heck correlation is the best among the evaluated correlations in the turbulent region. A modified Chisholm correlation was proposed, which is better than all of the evaluated correlations in the turbulent region and its mean relative error is about 29%. For refrigerants only, the new correlation and Muller-Steinhagen and Heck correlation are very close to each other and give better agreement than the other evaluated correlations.

Two-Phase Flow Through Square and Circular Microchannels—Effects of Channel Geometry

2004 ◽  
Vol 126 (4) ◽  
pp. 546-552 ◽  
Author(s):  
Peter M.-Y. Chung ◽  
Masahiro Kawaji ◽  
Akimaro Kawahara ◽  
Yuichi Shibata
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Characteristics ◽  
Separated Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Channel Geometry ◽  
Frictional Pressure Drop ◽  
Channel Shape

An adiabatic experiment was conducted to investigate the effect of channel geometry on gas-liquid two-phase flow characteristics in horizontal microchannels. A water-nitrogen gas mixture was pumped through a 96 μm square microchannel and the resulting flow pattern, void fraction and frictional pressure drop data were compared with those previously reported by the authors for a 100 μm circular microchannel. The pressure drop data were best estimated using a separated-flow model and the void fraction increased non-linearly with volumetric quality, regardless of the channel shape. However, the flow maps exhibited transition boundaries that were shifted depending on the channel shape.

Experimental Investigation on Flow Patterns and Frictional Pressure Drop of Downward Air-Water Two-Phase Flow in Vertical Pipes

2013 ◽  
Author(s):  
Yuqing Xue ◽  
Huixiong Li ◽  
Tianyou Sheng ◽  
Changjiang Liao
Keyword(s):  
Pressure Drop ◽  
Flow Pattern ◽  
Oil Recovery ◽  
Two Phase Flow ◽  
Flow Patterns ◽  
Phase Flow ◽  
Vertical Pipe ◽  
Two Phase Flows ◽  
Two Phase ◽  
Frictional Pressure Drop

A large amount of air need be transported into the reservoir in the deep stratum to supply oxygen to some microbes in Microbial Enhanced Oil Recovery (MEOR). Air-water two-phase flows downward along vertical pipeline during the air transportation. Base on the experiment data described in this paper, the characteristics of air-water two phase flow patterns were investigated. The flow pattern map of air-water two phase flows in the pipe with inner diameter of 65 mm was drawn, criterions of flow pattern transition were discussed, and the dynamic signals of the pressure and the differential pressure of the two phase flow were recorded to characterize the three basic flow regimes indirectly. The frictional pressure drop of downward flow in vertical pipe must not be disregarded contrast with upward two phase flow in the vertical pipe because the buoyancy must be overcame when the gas flows downward along pipe, and there would be a maximum value of frictional when the flow pattern translated from slug flow to churn flow.

Predicting Two Phase Flow Pressure Drop With CFD and ANN

2010 ◽  
Author(s):  
I˙smail Teke ◽  
O¨zden Ag˘ra ◽  
Hakan Demir ◽  
S¸. O¨zgu¨r Atayılmaz
Keyword(s):  
Pressure Drop ◽  
Flow Model ◽  
Two Phase Flow ◽  
Saturation Temperature ◽  
Smooth Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Analytical Formulas ◽  
Flow Pressure ◽  
Good Agreement

In this study, the several well known two-phase viscosity models were used for predicting two-phase flow pressure drop in a smooth tube using Computational Fluid Dynamics (CFD) software at homogenous flow conditions. Pressure drop for two different mass flux values (300 and 650 kg/m2s) for R134a with a saturation temperature of 45 °C in a smooth tube has been modeled according to the homogenous flow model and the results have been compared with the analytical formulas and experimental data from the literature. Three different average viscosity correlations were used. It is seen that the numerical results are in a good agreement with the homogenous flow model and fall in ± 30% band. Also, the results derived from the average viscosity expression are in a good agreement with the results calculated using separated two-phase flow correlations. In addition to this, Artificial Neural Networks (ANNs) were employed for predicting the pressure drop in a horizontal smooth pipe. The trained network gives the best values over the correlations with less than 1% mean relative error.

Correlations of the Holdup and the Frictional Pressure Drop in Air-Water Two-Phase Flow in a Flat Capillary Rectangular Channel

2004 ◽  
Author(s):  
Hideo Ide ◽  
Tohru Fukano
Keyword(s):  
Pressure Drop ◽  
Aspect Ratio ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Flow Phenomena

Both vertical upward and horizontal gas-liquid two-phase flows in a flat capillary rectangular channel were studied to clarify the flow phenomena, the holdup and the frictional pressure drop. The dimension of the channel used was 9.9 mm × 1.1 mm. The orientations of the channel were with the wide side vertical and the wide side horizontal. The differences between the flow characteristics in such orientations were investigated. New correlations of holdup and frictional pressure drop for flat capillary channels are proposed, in which the effect of aspect ratio has been taken into consideration.

Sign in / Sign up

Export Citation Format

Share Document