An Approximate Analysis and Prediction Method for Tip Clearance Loss in Axial Compressors

1994 ◽  
Vol 116 (4) ◽  
pp. 648-656 ◽  
Author(s):  
J. A. Storer ◽  
N. A. Cumpsty
Keyword(s):  
Simple Model ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Experimental Program ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Principal Mechanism ◽  
Axial Compressors ◽  
Tip Leakage ◽  
Clearance Flow

A simple model for loss created by the tip clearance flow in axial compressors is presented, based on an experimental program performed in conjunction with the Dawes three-dimensional Navier–Stokes calculation method. The principal mechanism of loss (entropy creation) caused by tip leakage flow has been established to be the mixing of flows of similar speeds but different direction. Calculations show that relative motion of the endwall relative to the tip has a small effect on clearance flow. The simple model correctly predicts the magnitude of tip clearance loss and the trend with changes of tip clearance for the cascade tested. For a given geometry the loss is almost exactly proportional to the ratio of tip clearance to blade span; the loss directly associated with the clearance is smaller than often assumed. The simple model for tip clearance loss has been expressed in terms of conventional nondimensional design variables (for example: solidity, aspect ratio, flow coefficient, loading coefficient) and from these the contribution to the overall loss of efficiency caused by tip leakage flow is conveniently represented. The trends are illustrated for a number of possible compressor design choices. Blade row loss increases more slowly than blade loading (for example, diffusion factor). As a result the decrement in stage efficiency associated with clearance flow decreases as the stage loading is raised in the practical range of flow and loading coefficients.

An Approximate Analysis and Prediction Method for Tip Clearance Loss in Axial Compressors

1993 ◽  
Author(s):  
J. A. Storer ◽  
N. A. Cumpsty
Keyword(s):  
Simple Model ◽  
Prediction Method ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Principal Mechanism ◽  
Axial Compressors ◽  
Tip Leakage ◽  
Clearance Flow

A simple model for loss created by the tip clearance flow in axial compressors is presented, based on an experimental programme performed in conjunction with the Dawes three-dimensional Navier-Stokes calculation method. The principal mechanism of loss (entropy creation) caused by tip leakage flow has been established to be the mixing of flows of similar speeds but different direction. Calculations who that relative motion of the endwall relative to the tip has a small effect on clearance flow. The simple model correctly predicts the magnitude of tip clearance loss and the trend with changes of tip clearance for the cascade tested. For a given geometry the loss is almost exactly proportional to the ratio of tip clearance to blade span; the loss directly associated with the clearance is smaller than often assumed. The simple model for tip clearance loss has been expressed in terms of conventional non-dimensional design variables (for example; solidity, aspect ratio, flow coefficient, loading coefficient) and from these the contribution to the overall loss of efficiency caused by tip leakage flow is conveniently represented. The trends are illustrated for a number of possible compressor design choices. Blade row loss increases more slowly than blade loading (for example diffusion factor). As a result the decrement in stage efficiency associated with clearance flow decreases as the stage loading is raised in the practical range of flow and loading coefficients.

Numerical Simulation of Tip Clearance Control in Axial Turbine Rotor: Part 2—Passive Control of Five Different Tip Platforms

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Passive Control ◽  
Suction Side ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

The tip leakage flow has significant effects on turbine in loss production, aerodynamic efficiency, etc. Then it’s important to minimize these effects for a better performance by adopting corresponding flow control. The active turbine tip clearance flow control with injection from the tip platform is given in Part-1 of this paper. This paper is Part-2 of the two-part papers focusing on the effect of five different passive turbine tip clearance flow control methods on the tip clearance flow physics, which consists of a partial suction side squealer tip (Partial SS Squealer), a double squealer tip (Double Side Squealer), a pressure side tip shelf with inclined squealer tip on a double squealer tip (Improved PS Squealer), a tip platform extension edge in pressure side (PS Extension) and in suction side (SS Extension) respectively. Combined with the turbine rotor and the numerical method mentioned in Part 1, the effects of passive turbine tip clearance flow controls on the tip clearance flow were sequentially simulated. The detailed tip clearance flow fields with different squealer rims were described with the streamline and the velocity vector in various planes parallel to the tip platform or normal to the tip leakage vortex core. Accordingly, the mechanisms of five passive controls were put in evidence; the effects of the passive controls on the turbine efficiency and the tip clearance flow field were highlighted. The results show that the secondary flow loss near the outer casing including the tip leakage flow and the casing boundary layer can be reduced in all the five passive control methods. Comparing the active control with the passive control, the effect brought by the active injection control on the tip leakage flow is evident. The turbine rotor efficiency could be increased via the rational passive turbine tip clearance flow control. The Improved PS Squealer had the best effect on turbine rotor efficiency, and it increased by 0.215%.

scholarly journals An Experimental Study of Tip Clearance Flow in a Radial Inflow Turbine

1998 ◽  
Author(s):  
R. Dambach ◽  
H. P. Hodson ◽  
I. Huntsman
Keyword(s):  
Tip Clearance ◽  
Leakage Flow ◽  
Hot Wire ◽  
Tip Leakage Flow ◽  
Axial Turbine ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Radial Turbine ◽  
Clearance Flow ◽  
Radial Inflow Turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualisation and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicates that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located towards midchord, where the effect of relative casing motion is weakened. Finally a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behaviour in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

Measurement and Prediction of Tip Clearance Flow in Linear Turbine Cascades

1993 ◽  
Vol 115 (3) ◽  
pp. 376-382 ◽  
Author(s):  
F. J. G. Heyes ◽  
H. P. Hodson
Keyword(s):  
Experimental Studies ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Pressure Gradients ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Turbine Cascades ◽  
Axial Turbines

This paper describes a simple two-dimensional model for the calculation of the leakage flow over the blade tips of axial turbines. The results obtained from calculations are compared with data obtained from experimental studies of two linear turbine cascades. One of these cascades has been investigated by the authors and previously unpublished experimental data are provided for comparison with the model. In each of the test cases examined, excellent agreement is obtained between the experimental and predicted data. Although ignored in the past, the importance of pressure gradients along the blade chord is highlighted as a major factor influencing the tip leakage flow.

The Influence of Tip Clearance Momentum Flux on Stall Inception in a High-Speed Axial Compressor

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Joshua D. Cameron ◽  
Matthew A. Bennington ◽  
Mark H. Ross ◽  
Scott C. Morris ◽  
Juan Du ◽  
...  
Keyword(s):  
Momentum Flux ◽  
High Speed ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Axial Position ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage

Experimental and numerical studies were conducted to investigate tip-leakage flow and its relationship to stall in a transonic axial compressor. The computational fluid dynamics (CFD) results were used to identify the existence of an interface between the approach flow and the tip-leakage flow. The experiments used a surface-streaking visualization method to identify the time-averaged location of this interface as a line of zero axial shear stress at the casing. The axial position of this line, denoted xzs, moved upstream with decreasing flow coefficient in both the experiments and computations. The line was consistently located at the rotor leading edge plane at the stalling flow coefficient, regardless of inflow boundary condition. These results were successfully modeled using a control volume approach that balanced the reverse axial momentum flux of the tip-leakage flow with the momentum flux of the approach fluid. Nonuniform tip clearance measurements demonstrated that movement of the interface upstream of the rotor leading edge plane leads to the generation of short length scale rotating disturbances. Therefore, stall was interpreted as a critical point in the momentum flux balance of the approach flow and the reverse axial momentum flux of the tip-leakage flow.

Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade

2014 ◽  
Vol 599-601 ◽  
pp. 368-371
Author(s):  
Zhi Hui Xu ◽  
He Bin Lv ◽  
Ru Bin Zhao
Keyword(s):  
Computational Simulation ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Blade Tip

Using blade tip winglet to control the tip leakage flow has been concerned in the field of turbomachinery. Computational simulation was conducted to investigate the phenomenological features of tip clearance flow. The simulation results show that suction-side winglet can reduce leakage flow intensity. The tip winglet can also decrease tip leakage mass flow and weaken tip leakage flow mixing with the mainstream and therefore reduce the total pressure loss at the blade tip.

Effect of clearance height on tip leakage flow reduced by a honeycomb tip in a turbine cascade

2018 ◽  
Vol 233 (10) ◽  
pp. 3564-3576
Author(s):  
Fu Chen ◽  
Yunfeng Fu ◽  
Jianyang Yu ◽  
Yanping Song
Keyword(s):  
Flow Resistance ◽  
Flow Characteristics ◽  
Tip Clearance ◽  
Small Scale ◽  
Leakage Flow ◽  
Turbine Cascade ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Vortex Movement

In this paper, the control mechanism of the honeycomb tip structure on the tip leakage flow of a turbine cascade is studied experimentally and numerically, and the sensitivity of tip leakage flow characteristics to different clearance heights from 0.5% to 2% based on the blade span are mainly discussed. A flat tip is considered as a comparative case. The results show that a part of the leakage flow enters the tip honeycomb cavity, forming small-scale vortices and mixes with the upper leakage fluid, which increases the flow resistance within the clearance. In the range of clearance height variation investigated, honeycomb tip structure can effectively reduce the leakage flow, and reduce the size and strength of the leakage vortex, so that the loss of the cascade is reduced. At a large tip clearance height, the unstable split of the vortex cores causes the vortex in the honeycomb cavities near pressure side to grow in size, so that the vortex extends further into the upper gap, where the turbulent blocking effect of the vortices on the leakage flow is increased. However, due to the vortex movement and the mixing between honeycomb vortices and the upper clearance flow, there is no obvious advantage in reducing the total loss of the cascade compared to the small tip clearance height.

Numerical simulation of unsteady tip clearance flow in an isolated axial compressor rotor blades row

2011 ◽  
Vol 226 (1) ◽  
pp. 82-93 ◽  
Author(s):  
R Taghavi-Zenouz ◽  
S Eslami
Keyword(s):  
Experimental Data ◽  
Axial Compressor ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow

Three-dimensional unsteady numerical simulations were carried out to analyse tip clearance flow in a low-speed isolated axial compressor rotor blades row. A flow solver has been used for the current study utilizing the large eddy simulation (LES) technique. Periodic tip leakage flow and its propagation trajectories were simulated in detail. A number of pseudo pressure transducers were imposed on the pressure side of the blade for detection of unsteady surface pressures to provide a calculation of tip leakage flow frequencies. Two different sizes of tip clearance were considered for simulations and analyses. Non-dimensional frequencies of the tip leakage flow were calculated and final results were compared to those of existing numerical and experimental data. Final results demonstrated that in contrast to the Reynolds averaged Navier–Stokes (RANS) model, the LES method shows considerable dependency of frequency characteristics of the tip leakage flow to the gap size and can detect different frequency spectrums along the blade surface. All the results obtained through the current numerical approach were in close agreement with those of existing experimental data.

Tip Leakage Flow in Radial Inflow Rotor of a Microturbine With Varying Blade-Shroud Clearance

2007 ◽  
Author(s):  
Qinghua Deng ◽  
Jiufang Niu ◽  
Zhenping Feng
Keyword(s):  
Three Dimensional ◽  
Flow Simulation ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Transverse Mass ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

In this paper, tip clearance flow in a radial inflow turbine rotor under the stage environment is investigated using a three-dimensional viscous flow simulation with three different blade-shroud gap heights of 1%, 2% and 3% of the local span. The results indicate that more relative casing motion increases the scraping effect on tip leakage flow at the rotor entrance. Also, the scraping flow can dominate the whole tip clearance at the rotor entrance when the velocity is high enough at the rotor tip diameter. Regardless of the transverse mass flow rates of the three tip clearances, the results strongly exhibit the characteristics of linearity when the relative meridional length S is greater than 40%. According to the analysis of leakage flow fields in the tip clearance, measures such as a circumference slot, axial slot, or honeycomb are proposed to be applied and placed at the shroud surface over the exducer of the rotor for effectively reducing the transverse flow.

scholarly journals The Role of Tip Leakage Flow in Spike-Type Rotating Stall Inception

2017 ◽  
Author(s):  
M. Hewkin-Smith ◽  
G. Pullan ◽  
S. D. Grimshaw ◽  
E. M. Greitzer ◽  
Z. S. Spakovszky
Keyword(s):  
Maximum Flow ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Corner Separation ◽  
Tip Leakage

This paper describes the role of tip leakage flow in creating the leading edge separation necessary for the onset of spike-type compressor rotating stall. A series of unsteady multi-passage simulations, supported by experimental data, are used to define and illustrate the two competing mechanisms that cause the high incidence responsible for this separation: blockage from a casing-suction-surface corner separation and forward spillage of the tip leakage jet. The axial momentum flux in the tip leakage flow determines which mechanism dominates. At zero tip clearance, corner separation blockage dominates. As the clearance is increased, the leakage flow reduces the blockage, moving the stall flow coefficient to lower flow, i.e., giving a larger unstalled flow range. Increased clearance, however, means an increase in leakage jet momentum and the contribution to leakage jet spillage. There is thus a clearance above which jet spillage dominates in creating incidence, so the stall flow coefficient increases and the flow range decreases with clearance. As a consequence there is a clearance for maximum flow range; for the two rotors in this study, the value was approximately 0.5% chord. The chord-wise distribution of the leakage axial momentum is also important in determining stall onset. Shifting the distribution towards the trailing edge increases the flow range of a leakage jet dominated geometry and reduces the flow range of a corner separation dominated geometry. Guidelines are developed for flow range enhancement through control of tip leakage flow axial momentum magnitude and distribution. An example is given of how this might be achieved.

Sign in / Sign up

Export Citation Format

Share Document