A Review of Predictive Efforts for Transport Phenomena in Axial Flow Compressors

1991 ◽  
Vol 113 (2) ◽  
pp. 175-179 ◽  
Author(s):  
A. J. Wennerstrom
Keyword(s):  
Turbulent Transport ◽  
Transport Phenomena ◽  
Axial Flow ◽  
Secondary Flows ◽  
Historical Background ◽  
Future Trends ◽  
Radial Transport ◽  
Axial Flow Compressors

Transport phenomena as they apply to throughflow calculations in axial-flow compressors are reviewed. An historical background is presented. Then the debate raised by the Adkins and Smith versus the Gallimore and Cumpsty approaches to radial transport is discussed. This debate was resolved in that it was finally concluded that both turbulent transport and convective secondary flows play a role in spanwise transport. Other major related efforts mentioned are those of Hirsch and his colleagues and Papailiou and his colleagues. Readers are encouraged to reconsider exploitation of the work of Kerrebrock and Mikolajczak concerning circumferential transport. Comments on future trends are offered.

Secondary Flow, Turbulent Diffusion, and Mixing in Axial-Flow Compressors

1987 ◽  
Vol 109 (4) ◽  
pp. 455-469 ◽  
Author(s):  
D. C. Wisler ◽  
R. C. Bauer ◽  
T. H. Okiishi
Keyword(s):  
Secondary Flow ◽  
Turbulent Diffusion ◽  
Fluid Motion ◽  
Axial Flow ◽  
Secondary Flows ◽  
Tracer Gas ◽  
Order Of Magnitude ◽  
Diffusive Effects ◽  
Experimental Findings ◽  
Axial Flow Compressors

The relative importance of convection by secondary flows and diffusion by turbulence as mechanisms responsible for mixing in multistage, axial-flow compressors has been investigated by using the ethylene tracer-gas technique and hot-wire anemometry. The tests were conducted at two loading levels in a large, low-speed, four-stage compressor. The experimental results show that considerable cross-passage and spanwise fluid motion can occur and that both secondary flow and turbulent diffusion can play important roles in the mixing process, depending upon location in the compressor and loading level. In the so-called freestream region, turbulent diffusion appeared to be the dominant mixing mechanism. However, near the endwalls and along airfoil surfaces at both loading levels, the convective effects from secondary flow were of the same order of magnitude as, and in some cases greater than, the diffusive effects from turbulence. Calculations of the secondary flowfield and mixing coefficients support the experimental findings.

Loss Reduction in Axial-Flow Compressors Through Low-Speed Model Testing

1985 ◽  
Vol 107 (2) ◽  
pp. 354-363 ◽  
Author(s):  
D. C. Wisler
Keyword(s):  
Flow Separation ◽  
High Speed ◽  
Three Dimensional ◽  
Axial Flow ◽  
Secondary Flows ◽  
Stall Margin ◽  
Low Speed ◽  
High Loss ◽  
Aerodynamic Model ◽  
Axial Flow Compressors

A systematic procedure for reducing losses in axial-flow compressors is presented. In this procedure, a large, low-speed, aerodynamic model of a high-speed core compressor is designed and fabricated based on aerodynamic similarity principles. This model is then tested at low speed where high-loss regions associated with three-dimensional endwall boundary layers, flow separation, leakage, and secondary flows can be located, detailed measurements made, and loss mechanisms determined with much greater accuracy and much lower cost and risk than is possible in small, high-speed compressors. Design modifications are made by using custom-tailored airfoils and vector diagrams, airfoil endbends, and modified wall geometries in the high-loss regions. The design improvements resulting in reduced loss or increased stall margin are then scaled to high speed. This paper describes the procedure and presents experimental results to show that in some cases endwall loss has been reduced by as much as 10 percent, flow separation has been reduced or eliminated, and stall margin has been substantially improved by using these techniques.

scholarly journals Steady flow separation patterns in a 45 degree junction

2000 ◽  
Vol 411 ◽  
pp. 1-38 ◽  
Author(s):  
C. ROSS ETHIER ◽  
SUJATA PRAKASH ◽  
DAVID A. STEINMAN ◽  
RICHARD L. LEASK ◽  
GREGORY G. COUCH ◽  
...  
Keyword(s):  
Flow Separation ◽  
Stokes Equations ◽  
Bypass Graft ◽  
Three Dimensional ◽  
Symmetry Plane ◽  
Axial Flow ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Measured Velocity ◽  
Curved Tube

Numerical and experimental techniques were used to study the physics of flow separation for steady internal flow in a 45° junction geometry, such as that observed between two pipes or between the downstream end of a bypass graft and an artery. The three-dimensional Navier–Stokes equations were solved using a validated finite element code, and complementary experiments were performed using the photochromic dye tracer technique. Inlet Reynolds numbers in the range 250 to 1650 were considered. An adaptive mesh refinement approach was adopted to ensure grid-independent solutions. Good agreement was observed between the numerical results and the experimentally measured velocity fields; however, the wall shear stress agreement was less satisfactory. Just distal to the ‘toe’ of the junction, axial flow separation was observed for all Reynolds numbers greater than 250. Further downstream (approximately 1.3 diameters from the toe), the axial flow again separated for Re [ges ] 450. The location and structure of axial flow separation in this geometry is controlled by secondary flows, which at sufficiently high Re create free stagnation points on the model symmetry plane. In fact, separation in this flow is best explained by a secondary flow boundary layer collision model, analogous to that proposed for flow in the entry region of a curved tube. Novel features of this flow include axial flow separation at modest Re (as compared to flow in a curved tube, where separation occurs only at much higher Re), and the existence and interaction of two distinct three-dimensional separation zones.

LSI Microcomputer and Digital Control

1975 ◽  
Vol 97 (2) ◽  
pp. 149-156 ◽  
Author(s):  
I. Lee
Keyword(s):  
Digital Control ◽  
Historical Background ◽  
Control System Design ◽  
Future Trends ◽  
Digital Control System ◽  
Control Logic ◽  
Present Trend ◽  
Potential Impact ◽  
Microprocessor Technology ◽  
And Control

This paper gives a tutorial presentation and overview of LSI microprocessor technology for control engineers and control logic designers. The historical background, present status and future trends of this dynamic technology are presented, and its enormous potential impact on digital control system design and implementation is explored through examples and extrapolation of the present trend.

Measurements of Secondary Losses in a Turbine Cascade With the Implementation of Nonaxisymmetric Endwall Contouring

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
D. C. Knezevici ◽  
S. A. Sjolander ◽  
T. J. Praisner ◽  
E. Allen-Bradley ◽  
E. A. Grover
Keyword(s):  
Kinetic Energy ◽  
Axial Flow ◽  
Surface Flow ◽  
Secondary Flows ◽  
Test Facility ◽  
Suction Surface ◽  
Blade Passage ◽  
Low Pressure Turbine ◽  
Endwall Contouring ◽  
Pressure And Velocity Measurements

An approach to endwall contouring has been developed with the goal of reducing secondary losses in highly loaded axial flow turbines. The present paper describes an experimental assessment of the performance of the contouring approach implemented in a low-speed linear cascade test facility. The study examines the secondary flows of a cascade composed of Pratt & Whitney PAKB airfoils. This airfoil has been used extensively in low-pressure turbine research, and the present work adds intrapassage pressure and velocity measurements to the existing database. The cascade was tested at design incidence and at an inlet Reynolds number of 126,000 based on inlet midspan velocity and axial chord. Quantitative results include seven-hole pneumatic probe pressure measurements downstream of the cascade to assess blade row losses and detailed seven-hole probe measurements within the blade passage to track the progression of flow structures. Qualitative results take the form of oil surface flow visualization on the endwall and blade suction surface. The application of endwall contouring resulted in lower secondary losses and a reduction in secondary kinetic energy associated with pitchwise flow near the endwall and spanwise flow up the suction surface within the blade passage. The mechanism of loss reduction is discussed in regard to the reduction in secondary kinetic energy.

Influence of Turbulent Flow Characteristics and Coherent Vortices on the Pressure Recovery of Annular Diffusers: Part A — Experimental Results

2015 ◽  
Author(s):  
Marcus Kuschel ◽  
Bastian Drechsel ◽  
David Kluß ◽  
Joerg R. Seume
Keyword(s):  
Boundary Layer ◽  
High Pressure ◽  
Static Pressure ◽  
Turbulent Transport ◽  
Axial Flow ◽  
Pressure Recovery ◽  
Turbulence Structure ◽  
Reynolds Stresses ◽  
Wide Range ◽  
Operating Points

Exhaust diffusers downstream of turbines are used to transform the kinetic energy of the flow into static pressure. The static pressure at the turbine outlet is thus decreased by the diffuser, which in turn increases the technical work as well as the efficiency of the turbine significantly. Consequently, diffuser designs aim to achieve high pressure recovery at a wide range of operating points. Current diffuser design is based on conservative design charts, developed for laminar, uniform, axial flow. However, several previous investigations have shown that the aerodynamic loading and the pressure recovery of diffusers can be increased significantly if the turbine outflow is taken into consideration. Although it is known that the turbine outflow can reduce boundary layer separations in the diffuser, less information is available regarding the physical mechanisms that are responsible for the stabilization of the diffuser flow. An analysis using the Lumley invariance charts shows that high pressure recovery is only achieved for those operating points in which the near-shroud turbulence structure is axi-symmetric with a major radial turbulent transport component. This turbulent transport originates mainly from the wake and the tip vortices of the upstream rotor. These structures energize the boundary layer and thus suppress separation. A logarithmic function is shown that correlates empirically the pressure recovery vs. the relevant Reynolds stresses. The present results suggest that an improved prediction of diffuser performance requires modeling approaches that account for the anisotropy of turbulence.

Sign in / Sign up

Export Citation Format

Share Document