Limit Loads of Mechanical Components and Structures Using the GLOSS R-Node Method

1992 ◽  
Vol 114 (2) ◽  
pp. 201-208 ◽  
Author(s):  
R. Seshadri ◽  
C. P. D. Fernando
Keyword(s):  
Practical Interest ◽  
Limit Load ◽  
Load Control ◽  
Plastic Collapse ◽  
Element Analysis ◽  
Limit Loads ◽  
Linear Elastic ◽  
Reference Stress ◽  
Stress Classification ◽  
Mechanical Components

A method for determining plastic collapse loads of mechanical components and structures on the basis of two linear elastic finite element analysis is presented in this paper. The r-nodes, which are essentially statically determinate locations, are obtained by GLOSS analysis. The plastic collapse loads are determined for statically determinate and indeterminate components and structures by using the single-bar and the multibar models, respectively. The paper also attempts to unify the concepts of load-control, limit load, reference stress and stress-classification. The GLOSS R-Node method is applied to several component configurations of practical interest.

LIMIT LOADS OF FRAMED STRUCTURES AND ARCHES USING THE GLOSS R-NODE METHOD

1993 ◽  
Vol 17 (2) ◽  
pp. 197-214
Author(s):  
C.P.D. Fernando ◽  
R. Seshadri
Keyword(s):  
Finite Element ◽  
Approximate Method ◽  
Equivalent Stress ◽  
Limit Load ◽  
Load Control ◽  
Finite Element Analyses ◽  
Limit Loads ◽  
Framed Structures ◽  
Linear Elastic ◽  
Reference Stress

An approximate method for determining limit loads of mechanical components and structures on the basis of two linear elastic finite element analyses is described. The load-control nature of the redistribution nodes (r-nodes) leads to considerable simplifications. The combined r-node equivalent stress, which can be obtained by invoking an appropriate multibar mode, can be identified with the reference stress. The method is applied to beam, framed and arched structures, and the limit load estimates obtained are reasonably accurate.

Simplified Limit Load Determination Using the mα-Tangent Method

2008 ◽  
Author(s):  
R. Seshadri ◽  
M. M. Hossain
Keyword(s):  
Finite Element ◽  
Rapid Determination ◽  
Limit Load ◽  
Finite Element Analyses ◽  
Element Analysis ◽  
Limit Loads ◽  
Linear Elastic ◽  
Tangent Method ◽  
Mechanical Components

Limit load determination of mechanical components and structures by the mα-tangent method is proposed herein. The proposed technique is a simplified method that enables rapid determination of limit loads for a general class of mechanical components and structures. The method makes use of statically admissible stress field based on a linear elastic finite element analysis to estimate the limit loads. The method is applied to a number of mechanical component configurations and the results compare well with those obtained by the corresponding elastic-plastic finite element analyses results.

Simplified Limit Load Determination Using the mα-Tangent Method

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
R. Seshadri ◽  
M. M. Hossain
Keyword(s):  
Finite Element ◽  
Rapid Determination ◽  
Limit Load ◽  
Finite Element Analyses ◽  
Element Analysis ◽  
Limit Loads ◽  
Linear Elastic ◽  
Tangent Method ◽  
Mechanical Components

Limit load determination of mechanical components and structures by the mα-tangent method is proposed herein. The proposed technique is a simplified method that enables rapid determination of limit loads for a general class of mechanical components and structures. The method makes use of statically admissible stress field based on a linear elastic finite element analysis to estimate the limit loads. The method is applied to a number of mechanical component configurations and the results compare well with those obtained by the corresponding elastic-plastic finite element analyses results.

Validation of Plastic Collapse Assessments Using BS 7910:2013 and R6 Procedures

2013 ◽  
Author(s):  
Şefika Elvin Eren ◽  
Tyler London ◽  
Yang Yang ◽  
Isabel Hadley
Keyword(s):  
Finite Element Analysis ◽  
Limit Load ◽  
Plastic Collapse ◽  
Element Analysis ◽  
Metallic Structures ◽  
British Standard ◽  
Reference Stress ◽  
Fracture Assessment ◽  
The Difference ◽  
Reference Stress Approach

The British Standard, BS 7910 Guide to Methods for Assessing the Acceptability of Flaws in Metallic Structures is currently under revision [1]. Major changes have been undertaken, especially in the fracture assessment routes, and this paper specifically addresses the assessment of proximity to plastic collapse, usually expressed as the parameter Lr via either a reference stress or limit load approach. In the new edition of BS 7910, the reference stress approach has been retained for the assessment of many geometries, mainly for reasons of continuity. However, new limit load solutions (originating in the R6 procedure) are given for use in the assessments of strength mismatched structures or clad plates. In general, a reference stress solution and a limit load solution for the same geometry should deliver the same value of Lr. However, recent comparative studies have shown differences in the assessment of plastic collapse depending on whether the reference stress solutions in BS 7910:2013 or the limit load solutions in R6 are used for the calculation of Lr. In this paper, the extent of the difference in the assessment results with respect to the choice of solutions and boundary conditions are discussed. The results of the assessments in accordance with BS 7910 and R6 are compared with the results of numerical assessments obtained via Finite Element Analysis (FEA). The collapse loads observed in various wide plate tests conducted in the last 20 years are also compared with the collapse loads predicted by BS 910:2013, R6 and FEA. Finally, observations regarding the accuracy of different Codes and FEA are discussed.

Local Limit-Load Analysis Using the mβ Method

2006 ◽  
Vol 129 (2) ◽  
pp. 296-305 ◽  
Author(s):  
R. Adibi-Asl ◽  
R. Seshadri
Keyword(s):  
Lower Bound ◽  
Upper Bound ◽  
Local Limit ◽  
Limit Load ◽  
Element Analysis ◽  
Limit Loads ◽  
Linear Elastic ◽  
Reference Volume ◽  
Component Design ◽  
Load Analysis

Several upper-bound limit-load multipliers based on elastic modulus adjustment procedures converge to the lowest upper-bound value after several linear elastic iterations. However, pressure component design requires the use of lower-bound multipliers. Local limit loads are obtained in this paper by invoking the concept of “reference volume” in conjunction with the mβ multiplier method. The lower-bound limit loads obtained compare well to inelastic finite element analysis results for several pressure component configurations.

Limit Loads for Pipe Elbows With Internal Pressure Under In-Plane Closing Bending Moments

1998 ◽  
Vol 120 (1) ◽  
pp. 35-42 ◽  
Author(s):  
M. A. Shalaby ◽  
M. Y. A. Younan
Keyword(s):  
Finite Element Analysis ◽  
Internal Pressure ◽  
Limit Load ◽  
Nonlinear Finite Element ◽  
Radius Of Curvature ◽  
Plastic Collapse ◽  
Bending Moments ◽  
Element Analysis ◽  
Pipe Bend ◽  
Limit Loads

The purpose of this study is to determine limit loads for pipe elbows subjected to in-plane bending moments that tend to close the elbow (i.e., decrease its radius of curvature), and the influence of internal pressure on the value of the limit load. Load-deflection curves were obtained, and from these curves plastic collapse or instability loads at various values of internal pressure were determined. This was done for different pipe bend factors (h = Rt/r2) using the nonlinear finite element analysis code (ABAQUS) with its special elbow element. The limit load was found to increase and then decrease with increasing pressure for all the elbow geometries studied.

Conceptual Models for Understanding the Role of the R-Nodes in Plastic Collapse

1997 ◽  
Vol 119 (3) ◽  
pp. 374-378 ◽  
Author(s):  
S. P. Mangalaramanan
Keyword(s):  
Conceptual Models ◽  
Minimum Weight ◽  
Equivalent Stress ◽  
Plastic Collapse ◽  
Simple Relationship ◽  
Linear Elastic ◽  
Reference Stress ◽  
Mechanical Components ◽  
Integrity Assessments

The r-nodes (redistribution nodes) are locations in mechanical components and structures that are load-controlled, and therefore insensitive to material constitutive relationships. These locations and their respective equivalent stress values can be approximately determined on the basis of two linear elastic analyses. By invoking equilibrium considerations, a simple relationship can be established between the “combined r-node equivalent stress” and the plastic collapse loads. On account of its load-controlled nature, the combined r-node equivalent stress can be identified with the reference stress, which is extensively used in carrying out pressure component integrity assessments. The concept of r-nodes is also related to the primary stresses in pressure components, and in designing mechanical components and structures for minimum weight. This paper proposes simple phenomenological models in an attempt to characterize the functioning of r-nodes.

Reference Volume Consideration in the mα-Tangent Method Based Linear Elastic Analysis

2011 ◽  
Author(s):  
R. Adibi-Asl ◽  
M. M. Hossain ◽  
S. L. Mahmood ◽  
P. S. R. Gudimetla ◽  
R. Seshadri
Keyword(s):  
Finite Element ◽  
Rapid Determination ◽  
Limit Load ◽  
Elastic Analysis ◽  
Element Analysis ◽  
Limit Loads ◽  
Linear Elastic ◽  
Reference Volume ◽  
Tangent Method

Limit loads for pressure components are determined on the basis of a single linear elastic finite element analysis by invoking the concept of kinematically active (reference) volume in the context of the “mα-tangent” method. The resulting technique enables rapid determination of lower bound limit load for pressure components by eliminating the kinematically inactive volume. This method is applied to a number of practical components with different percentages of inactive volume. The results are compared with the corresponding inelastic finite element results, or available analytical solutions.

Limit Load Analysis of Cracked Components Using the Reference Volume Method

2006 ◽  
Vol 129 (3) ◽  
pp. 391-399 ◽  
Author(s):  
R. Adibi-Asl ◽  
R. Seshadri
Keyword(s):  
Elastic Modulus ◽  
Three Dimensional ◽  
Local Limit ◽  
Limit Load ◽  
Multiple Cracks ◽  
Element Analysis ◽  
Limit Loads ◽  
Integrity Assessment ◽  
Reference Volume ◽  
Volume Method

Cracks and flaws occur in mechanical components and structures, and can lead to catastrophic failures. Therefore, integrity assessment of components with defects is carried out. This paper describes the Elastic Modulus Adjustment Procedures (EMAP) employed herein to determine the limit load of components with cracks or crack-like flaw. On the basis of linear elastic Finite Element Analysis (FEA), by specifying spatial variations in the elastic modulus, numerous sets of statically admissible and kinematically admissible distributions can be generated, to obtain lower and upper bounds limit loads. Due to the expected local plastic collapse, the reference volume concept is applied to identify the kinematically active and dead zones in the component. The Reference Volume Method is shown to yield a more accurate prediction of local limit loads. The limit load values are then compared with results obtained from inelastic FEA. The procedures are applied to a practical component with crack in order to verify their effectiveness in analyzing crack geometries. The analysis is then directed to geometries containing multiple cracks and three-dimensional defect in pressurized components.

Limit Loads for Laterally Loaded I-Section Beams With Consideration of Shear

2003 ◽  
Vol 47 (02) ◽  
pp. 83-91
Author(s):  
L. Belenkiy ◽  
Y. Raskin
Keyword(s):  
Physical Model ◽  
Limit Load ◽  
Nonlinear Finite Element ◽  
Shear Forces ◽  
Element Analysis ◽  
Limit Loads ◽  
Closed Form Solutions ◽  
Engineering Technique ◽  
Laterally Loaded ◽  
The Web

The paper examines an effect of shear forces on limit load for I-section beams carrying later alloads. The problem is solve don the basis of a physical model, which enables one to take into account the effect of a resistance of beam flanges to the plastic shears train in the web of the beam. The physical model for the evaluation of limit loads was veriŽed using nonlinear finite element analysis. An engineering technique for the calculation of limit loads for shiphull beams subjected to large shear forces was developed using this model. As illustrative examples, the paper shows the application of the proposed technique to obtain closed-form solutions for the prediction of limit loads.

Sign in / Sign up

Export Citation Format

Share Document