scholarly journals Discussion: “Analysis of Short Squeeze Film Dampers With a Central Groove” (San Andres, Luis A., 1992, ASME J. Tribol., 114, pp. 659–664)

1992 ◽  
Vol 114 (4) ◽  
pp. 664-664
Author(s):  
R. J. Rogers ◽  
Y. Hu
Keyword(s):  
Squeeze Film ◽  
Squeeze Film Dampers ◽  
San Andres

On the Numerical Prediction of Finite Length Squeeze Film Dampers Performance With Free Air Entrainment

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Tilmer H. Méndez ◽  
Jorge E. Torres ◽  
Marco A. Ciaccia ◽  
Sergio E. Díaz
Keyword(s):  
Finite Length ◽  
Air Entrainment ◽  
Squeeze Flow ◽  
Squeeze Film ◽  
Air Entrapment ◽  
Film Rupture ◽  
Subsequent Formation ◽  
Squeeze Film Dampers ◽  
Entrained Air ◽  
San Andres

Squeeze film dampers (SFDs) are commonly used in turbomachinery to dampen shaft vibrations in rotor-bearing systems. The main factor deterring the success of analytical models for the prediction of SFD’s performance lies on the modeling of dynamic film rupture. Usually, the cavitation models developed for journal bearings are applied to SFDs. Yet, the characteristic motion of the SFD results in the entrapment of air into the oil film, producing a bubbly mixture that cannot be represented by these models. There is a need to identify and understand the parameters that affect air entrainment and subsequent formation of a bubbly air-oil mixture within the lubricant film. A previous model by and Diazand San Andrés (2001, “A Model for Squeeze Film Dampers Operating With Air Entrapment and Validation With Experiments,” ASME J. Tribol., 123, pp. 125–133) advanced estimation of the amount of film-entrapped air based on a nondimensional number that related both geometrical and operating parameters but limited to the short bearing approximation (i.e., neglecting circumferential flow). The present study extends their work to consider the effects of finite length-to-diameter ratios. This is achieved by means of a finite volume integration of the two-dimensional, Newtonian, compressible Reynolds equation combined with the effective mixture density and viscosity defined in the work of Diaz and San Andrés. A flow balance at the open end of the film is devised to estimate the amount of air entrapped within the film. The results show, in dimensionless plots, a map of the amount of entrained air as a function of the feed-squeeze flow number, defined by Diaz and San Andrés, and the length-to-diameter ratio of the damper. Entrained air is shown to decrease as the L/D ratio increases, going from the approximate solution of Diaz and San Andrés for infinitely short SFDs down to no air entrainment for an infinite length SFD. The results of this research are of immediate engineering applicability. Furthermore, they represent a firm step to advance the understanding of the effects of air entrapment on the performance of SFDs.

A Theoretical Model for Squeeze Film Dampers Operating with Air Entrainment

2007 ◽  
Vol 353-358 ◽  
pp. 1683-1687
Author(s):  
Chun Yu Zhao ◽  
Hong Liang Yao ◽  
Feng Lin ◽  
Bang Chun Wen
Keyword(s):  
Hydrodynamic Lubrication ◽  
Control Volume ◽  
Air Entrainment ◽  
Ideal Gas ◽  
Squeeze Film ◽  
Computational Domain ◽  
Squeeze Film Dampers ◽  
Hydrodynamic Lubrication Theory ◽  
Volume Method ◽  
San Andres

A continuum model of the evolution of air ingestion and entrainment for open-ended squeeze film dampers is proposed in this paper. Hydrodynamic lubrication theory is extended to lubrication with mixture of a Newtonian liquid and an ideal gas. The solution to the universal Reynolds equation is determined numerically using a control volume method (Elrod algorithm) and the forth-order Range-Kutta method. This method conserves mass throughout the computational domain including air ingestion and entrainment. Excellent agreement is found with the experimental works of Diaz and San Andrès for the squeeze film damper [1, 2].

Damping and Inertia Coefficients for Two End Sealed Squeeze Film Dampers With a Central Groove: Measurements and Predictions

2013 ◽  
Vol 135 (11) ◽  
Author(s):  
Luis San Andrés ◽  
Sanjeev Seshagiri
Keyword(s):  
Gas Turbines ◽  
Short Length ◽  
System Stability ◽  
Single Frequency ◽  
Squeeze Film ◽  
Test Results ◽  
Piston Rings ◽  
Damping Coefficients ◽  
Squeeze Film Dampers ◽  
San Andres

Aircraft engine rotors, invariably supported on rolling element bearings with little damping, are particularly sensitive to rotor imbalance and sudden maneuver loads. Most engines incorporate squeeze film dampers (SFDs) as a means to dissipate mechanical energy from rotor motions and to ensure system stability. The paper experimentally quantifies the dynamic forced performance of two end sealed SFDs with dimensions and an operating envelope akin to those in actual jet engine applications. The current experimental results complement and extend prior research conducted with open ends SFDs (San Andrés, 2012, “Damping and Inertia Coefficients for Two Open Ends Squeeze Film Dampers With a Central Groove: Measurements and Predictions,” ASME J. Eng. Gas Turbines Power, 134, p. 102506). In the tests, two journals make for two SFD configurations, both with a diameter D = 127 mm and nominal radial film clearance c = 0.127 mm. One short length damper has film lands with extent L = 12.7 mm, while the other has 25.4 mm ( = 2L) land lengths. A central groove of length LG = L and depth at ¾ L separates the film lands. A light viscosity lubricant is supplied into the central groove via three orifices, 120 deg apart, and then flows through the film lands whose ends are sealed with tight piston rings. The oil pushes through the piston rings to discharge at ambient pressure. In the tests, a static load device pulls the damper structure to increasing eccentricities (maximum 0.38c) and external shakers exert single-frequency loads 50–250 Hz, inducing circular orbits with amplitudes equaling ∼5% of the film clearance. The lubricant feed and groove pressures and flow rates through the top and bottom film lands are recorded to determine the flow resistances through the film lands and the end seals. Measured dynamic pressures in the central groove are as large as those in the film lands, thus demonstrating a strong flow interaction, further intensified by the piston ring end seals which are effective in preventing side leakage. Dynamic pressures and reaction loads are substantially higher than those recorded with the open ends dampers. Comparisons to test results for two identical damper configurations but open ended (San Andrés, 2012, “Damping and Inertia Coefficients for Two Open Ends Squeeze Film Dampers With a Central Groove: Measurements and Predictions,” ASME J. Eng. Gas Turbines Power, 134, p. 102506) demonstrate at least a threefold increase in direct damping coefficients and no less than a double increment in added mass coefficients. Predictions from a physics-based model that includes the central groove, the lubricant feed holes, and the end seals' flow conductances are in agreement with the test results for the short length damper. For the long damper, the predicted damping coefficients are in good agreement with the measurements, while the added masses are under-predicted by ∼25%.

Solutions for the Combined Motion of Finite Length Squeeze Film Dampers Around the Bearing Center

1996 ◽  
Vol 118 (3) ◽  
pp. 617-622 ◽  
Author(s):  
J. X. Zhang ◽  
J. B. Roberts
Keyword(s):  
Finite Length ◽  
Wall Stress ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Mean Flow ◽  
Inertia Effects ◽  
Combined Motion ◽  
Squeeze Film Dampers ◽  
San Andres ◽  
Analytical Expressions

Analytical expressions for the hydrodynamic forces, and four related dynamic coefficients, are presented for finite length squeeze film dampers (SFDs) executing combined radial and tangential motion around the bearing center, with small amplitude. Previous analyses by Mulcahy (1980) and San Andres and Vance (1987) are shown to be particular cases of the present treatment. The influence of combined motion on the coefficients is found to differ, in several respects, from that which can be deduced from results for one dimensional radial motion and circular centred orbital motion. The effects of combined motion on the mean flow velocity and the wall stress are also studied. The study provides further insight into the validity of bulk flow assumptions, often used when dealing with lubrication problems where fluid inertia effects are significant.

Nonlinear Analysis of Rotor-Bearing Systems Using Component Mode Synthesis

1983 ◽  
Vol 105 (3) ◽  
pp. 606-614 ◽  
Author(s):  
H. D. Nelson ◽  
W. L. Meacham ◽  
D. P. Fleming ◽  
A. F. Kascak
Keyword(s):  
Forced Response ◽  
Component Mode Synthesis ◽  
Squeeze Film ◽  
System Response ◽  
Reduced Order ◽  
Squeeze Film Dampers ◽  
Rotor Bearing ◽  
System Equations ◽  
Transient System ◽  
Blade Loss

The method of component mode synthesis is developed to determine the forced response of nonlinear, multishaft, rotor-bearing systems. The formulation allows for simulation of system response due to blade loss, distributed unbalance, base shock, maneuver loads, and specified fixed frame forces. The motion of each rotating component of the system is described by superposing constraint modes associated with boundary coordinates and constrained precessional modes associated with internal coordinates. The precessional modes are truncated for each component and the reduced component equations are assembled with the nonlinear supports and interconnections to form a set of nonlinear system equations of reduced order. These equations are then numerically integrated to obtain the system response. A computer program, which is presently restricted to single shaft systems has been written and results are presented for transient system response associated with blade loss dynamics, with squeeze film dampers, and with interference rubs.

Influence of different flow regimes on the performance characteristics of a four-pad hydrostatic squeeze film damper loaded between pads

2019 ◽  
Vol 71 (3) ◽  
pp. 440-446
Author(s):  
Amina Nemchi ◽  
Ahmed Bouzidane ◽  
Aboubakeur Benariba ◽  
Hicham Aboshighiba
Keyword(s):  
Turbulent Flow ◽  
Load Capacity ◽  
Flow Regimes ◽  
Performance Characteristics ◽  
Squeeze Film ◽  
Eccentricity Ratio ◽  
Flow Conditions ◽  
Content Type ◽  
Turbulent Flow Regime ◽  
Squeeze Film Dampers

Purpose The purpose of this paper is to study the influence of different flow regimes on the dynamic characteristics of four-pad hydrostatic squeeze film dampers (SFDs) loaded between pads. Design/methodology/approach A numerical model based on Constantinescu’s turbulent lubrication theory using the finite difference method has been developed and presented to study the effect of eccentricity ratio on the performance characteristics of four-pad hydrostatic SFDs under different flow regimes. Findings It was found that the influence of turbulent flow on the dimensionless damping of four-pad hydrostatic SFDs appears to be essentially controlled by the eccentricity ratio. It was also found that the laminar flow presents higher values of load capacity compared to bearings operating under turbulent flow conditions. Originality/value In fact, the results obtained show that the journal bearing performances are significantly influenced by the turbulent flow regime. The study is expected to be useful to bearing designers.

Sign in / Sign up

Export Citation Format

Share Document