Simulation and Identification of Nonstationary Heat Transfer in a Nonuniform Friction Contact

1993 ◽  
Vol 115 (2) ◽  
pp. 299-306 ◽  
Author(s):  
O. Bogatin ◽  
I. Chersky ◽  
N. Starostin
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Three Dimensional ◽  
Unit Element ◽  
Separation Coefficient ◽  
Friction Contact ◽  
Nonstationary Heat Transfer ◽  
Thermal Fields ◽  
Simulation Results ◽  
Marching Method

The results of numerical simulation of nonstationary thermal fields in cylindrical friction junctions are presented. On the basis of the marching method, a numerical algorithm which imposes no restrictions on the value of heat flow separation coefficient is constructed. Simulation results are given for different bearing designs both for the two and three-dimensional cases. Using the developed algorithm as a base, a method allowing for reconstruction of heat release and, hence, friction moment values from temperature measurements in the stationary unit element is suggested. Reliability of the results is proved by experiments.

Calculation and Design Method Study of the Coil-Wound Heat Exchanger

2014 ◽  
Vol 1008-1009 ◽  
pp. 850-860 ◽  
Author(s):  
Zhou Wei Zhang ◽  
Jia Xing Xue ◽  
Ya Hong Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Exchanger ◽  
Design Method ◽  
Fluid Velocity ◽  
Exchange Process ◽  
Three Dimensional ◽  
Simulation Method ◽  
Physical Parameters ◽  
Numerical Result

A calculation method for counter-current type coil-wound heat exchanger is presented for heat exchange process. The numerical simulation method is applied to determine the basic physical parameters of wound bundles. By controlling the inlet fluid velocity varying in coil-wound heat exchanger to program and calculate the iterative process. The calculation data is analyzed by comparison of numerical result and the unit three dimensional pipe bundle model was built. Studies show that the introduction of numerical simulation can simplify the pipe winding process and accelerate the calculation and design of overall configuration in coil-wound heat exchanger. This method can be applied to the physical modeling and heat transfer calculation of pipe bundles in coil wound heat exchanger, program to calculate the complex heat transfer changing with velocity and other parameters, and optimize the overall design and calculation of spiral bundles.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

Characteristics of Heat Transfer and Flow on a Surface With Small-Scale Concave Spherical Pits

2008 ◽  
Author(s):  
J. S. Wang ◽  
Y. Qiu ◽  
L. Y. Li
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Small Scale ◽  
Heat Transfer Mechanism ◽  
Transfer Enhancement ◽  
Special Effect ◽  
Turbulent Drag Reduction ◽  
Turbulent Drag ◽  
Simulation Results ◽  
Turbulent Coherent Structure

Small-scale concave spherical pits, which have a special effect on heat transfer enhancement and turbulent drag reduction, are investigated by numerical simulation in detail. Two kinds of small-scale concave pits structures are designed on surface of a plate, which are located in the bottom of a rectangle channel. The characteristics of heat transfer and flow in channel are investigated and compared with a same channel with plate bottom by means of LES. Flow structure and temperature distribution near the pits are analyzed. The numerical simulation results indicate that the concave spherical pits disturb the flow field and vortex is induced by the pits. The turbulent coherent structure is affected by the induced vortex. The numerical simulation indicates that small scale pit can generate the vortex in couple. The range of vortex is accord with the array of small scale pit. The small scale pit can enhance the intensity of vortex. As a result, the temperature field near the pit is changed with generation of the vortex. The heat transfer mechanism on plate with small scale concave spherical pit is summarized.

Numerical Simulation Of A Microchannel For Microelectronic Cooling

2012 ◽  
Author(s):  
Wai Hing Wong ◽  
Normah Mohd. Ghazali
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Flux ◽  
Aspect Ratio ◽  
Three Dimensional ◽  
Large Temperature ◽  
Rectangular Microchannel ◽  
Numerical Work ◽  
Solid Region ◽  
Wall Interaction

Kertas kerja ini membincangkan simulasi berangka ke atas sinki haba saluran mikro dalam penyejukan alatan mikroelektronik. Model Dinamik Bendalir Berkomputer (CFD) tiga dimensi dibina menggunakan pakej komersil, FLUENT, untuk mengkaji fenomenon aliran bendalir dan pemindahan haba konjugat di dalam suatu sinki haba segi empat yang diperbuat daripada silikon. Model ditentusahkan dengan keputusan daripada uji kaji dan pengkajian berangka yang lepas untuk lingkungan nombor Reynolds kurang daripada 400 berdasarkan diameter hidraulik 86 mm. Kajian ini mengambil kira kesan kelikatan bendalir yang bersandaran dengan suhu dan keadaan aliran pra–membangun dari segi hidrodinamik dan haba. Model memberi maklumat tentang taburan suhu dan fluks haba yang terperinci di dalam sinki haba saluran mikro. Kecerunan suhu yang tinggi dicatat pada kawasan pepejal berdekatan dengan sumber. Fluks haba paling tinggi didapati pada dinding tepi saluran mikro diikuti oleh dinding atas dan bawah. Purata pekali pemindahan haba yang lebih tinggi bagi silikon menjadikan ia bahan binaan sinki haba saluran mikro yang lebih baik berbanding dengan kuprum dan aluminium. Peningkatan nisbah aspek saluran mikro yang bersegi empat memberi kecekapan penyejukan yang lebih tinggi kerana kelebaran saluran yang berkurangan memberi kecerunan halaju yang lebih tinggi dalam saluran. Nisbah aspek yang optimum yang diperoleh adalah dalam lingkungan 3.7 – 4.1. Kata kunci: Saluran mikro, CFD, FLUENT, simulasi berangka, penyejukan mikroelektron The paper discusses the numerical simulation of a micro–channel heat sink in microelectronics cooling. A three–dimensional Computational Fluid Dynamics (CFD) model was built using the commercial package, FLUENT, to investigate the conjugate fluid flow and heat transfer phenomena in a silicon–based rectangular microchannel heatsink. The model was validated with past experimental and numerical work for Reynolds numbers less than 400 based on a hydraulic diameter of 86 mm. The investigation was conducted with consideration of temperaturedependent viscosity and developing flow, both hydrodynamically and thermally. The model provided detailed temperature and heat flux distributions in the microchannel heatsink. The results indicate a large temperature gradient in the solid region near the heat source. The highest heat flux is found at the side walls of the microchannel, followed by top wall and bottom wall due to the wall interaction effects. Silicon is proven to be a better microchannel heatsink material compared to copper and aluminum, indicated by a higher average heat transfer. A higher aspect ratio in a rectangular microchannel gives higher cooling capability due to high velocity gradient around the channel when channel width decreases. Optimum aspect ratio obtained is in the range of 3.7 – 4.1. Key words: Microchannel, CFD, FLUENT, numerical simulation, microeletronics cooling

scholarly journals MEMS-Based Integrated Triaxial Electrochemical Seismometer

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1156
Author(s):  
Wenjie Qi ◽  
Bowen Liu ◽  
Tian Liang ◽  
Jian Chen ◽  
Deyong Chen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Ground Motion ◽  
Small Volume ◽  
Three Dimensional ◽  
Experimental Results ◽  
Good Prospect ◽  
High Symmetry ◽  
Noise Levels ◽  
Sensitivity Curves ◽  
Simulation Results

This paper presents a micro-electromechanical systems (MEMS)-based integrated triaxial electrochemical seismometer, which can detect three-dimensional vibration. By integrating three axes, the integrated triaxial electrochemical seismometer is characterized by small volume and high symmetry. The numerical simulation results inferred that the integrated triaxial electrochemical seismometer had excellent independence among three axes. Based on the experimental results, the integrated triaxial electrochemical seismometer had the advantage of small axial crosstalk and could detect vibration in arbitrary directions. Furthermore, compared with the uniaxial electrochemical seismometer, the integrated triaxial electrochemical seismometer had similar sensitivity curves ranging from 0.01 to 100 Hz. In terms of random ground motion response, high consistencies between the developed integrated triaxial electrochemical seismometer and the uniaxial electrochemical seismometer could be easily observed, which indicated that the developed integrated triaxial electrochemical seismometer produced comparable noise levels to those of the uniaxial electrochemical seismometer. These results validated the performance of the integrated triaxial electrochemical seismometer, which has a good prospect in the field of deep geophysical exploration and submarine seismic monitoring.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

scholarly journals The numerical simulation of enhanced heat transfer on a Linear Fresnel molten salt-type receiver tube filled with porous media

2019 ◽  
Vol 118 ◽  
pp. 01041
Author(s):  
Chenggang Yang ◽  
Yuning Zhang ◽  
Fenghe Yan ◽  
Wenguang Zhang ◽  
Wei Li
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Numerical Simulation ◽  
Porous Media ◽  
Molten Salt ◽  
Temperature Difference ◽  
Wall Temperature ◽  
Three Dimensional ◽  
Heat Transfer Fluid ◽  
Filling Rate

In this paper, three-dimensional numerical simulation was taken on a Linear Fresnel solar receiver tube using molten salt as heat transfer fluid (HTF), in which the porous media was filled to enhance the heat transfer efficiency. The simulation was to analyze the influence of the different conditions (filling rate, porosity and thermal conductivity) on heat transfer effect and wall temperature difference. The results revealed that the Nu (Nusselt number) increased firstly and then decreased with the increasing filling rate in both center filling and annular filling types. The optimal thermal performance were obtained when filling rate were 0.8 and 0.2 in center filling and annular filling, respectively. The Nu were about 1.7 and 1.5 times as the clear receiver. The circumferential temperature difference decreased firstly and then increased with filling rate increasing in both center filling and annular filling types. The lowest circumferential temperature differences were achieved at the filling rate 0.8 and 0.4 in center filling and annular filling types, and temperature difference decreased 15.88°C and 22°C compared with clear receiver, respectively. The Nu and PEC both decreased with porosity increasing. However, the thermal conductivity of porous media had little influence to the Nu and circumferential wall temperature.

Sign in / Sign up

Export Citation Format

Share Document