Analysis of Hydrostatic Journal Bearings With End Seals

1992 ◽  
Vol 114 (4) ◽  
pp. 802-811 ◽  
Author(s):  
L. A. San Andres
Keyword(s):  
Journal Bearings ◽  
Squeeze Film ◽  
Dynamic Force ◽  
Jet Engines ◽  
Fluid Inertia ◽  
Active Device ◽  
Typical Application ◽  
Liquid Compressibility ◽  
Squeeze Film Dampers ◽  
Direct Stiffness

An approximate analysis for the pressure field and dynamic force coefficients in turbulent flow, centered hydrostatic journal bearings (HJBs) with fluid inertia and liquid compressibility effects is presented. Results from the analysis show that HJBs with end seals have increased damping, better dynamic stability characteristics, as well as lower flow rates, than conventional HJBs. However, hydrostatic (direct) stiffness may be lost if excessively tight end seals are used. End seals are shown to compensate for the effect of liquid compressibility within the recess volume, and prescribe a net reduction in the whirl frequency ratio for hybrid operation. Hydrostatic squeeze film dampers (HSFD) with end seals are shown to be a viable alternative in applications where a tight control of the bearing leakage is important such as in jet-engines. Furthermore, HSFDs with end seals could be used as an active device to control the available damping in a typical application.

Analysis of Short Squeeze Film Dampers With a Central Groove

1992 ◽  
Vol 114 (4) ◽  
pp. 659-664 ◽  
Author(s):  
Luis A. San Andres
Keyword(s):  
Squeeze Film ◽  
Inertia Force ◽  
Dynamic Force ◽  
Fluid Inertia ◽  
Dynamic Flow ◽  
Low Frequencies ◽  
Squeeze Film Damper ◽  
Force Coefficients ◽  
Squeeze Film Dampers ◽  
Combined Action

A novel analysis for the dynamic force response of a squeeze film damper with a central feeding groove considers the dynamic flow interaction between the squeeze film lands and the feeding groove. For small amplitude centered motions and based on the short bearing model, corrected values for the damping and inertia force coefficients are determined. Correlations with existing experimental evidence is excellent. Analytical results show that the grooved-damper behaves at low frequencies as a single land damper. Dynamic force coefficients are determined to be frequency dependent. Analytical predictions show that the combined action of fluid inertia and groove volume—liquid compressibility affects the force coefficients for dynamic excitation at large frequencies.

scholarly journals Squeeze-Film Damper Technology: Part 1 — Prediction of Finite Length Damper Performance

1983 ◽  
Author(s):  
J. W. Lund ◽  
A. J. Smalley ◽  
J. A. Tecza ◽  
J. F. Walton
Keyword(s):  
Finite Length ◽  
Gas Turbines ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Inertia Effects ◽  
Strongly Coupled ◽  
Squeeze Film Damper ◽  
Rotor Systems ◽  
Squeeze Film Dampers ◽  
Calculation Results

Squeeze-film dampers are commonly used in gas turbine engines and have been applied successfully in a great many new designs, and also as retrofits to older engines. Of the mechanical components in gas turbines, squeeze-film dampers are the least understood. Their behavior is nonlinear and strongly coupled to the dynamics of the rotor systems on which they are installed. The design of these dampers is still largely empirical, although they have been the subject of a large number of past investigations. To describe recent analytical and experimental work in squeeze-film damper technology, two papers are planned. This abstract outlines the first paper, Part 1, which concerns itself with squeeze-film damper analysis. This paper will describe an analysis method and boundary conditions which have been developed recently for modelling dampers, and in particular, will cover the treatment of finite length, feed and drain holes and fluid inertia effects, the latter having been shown recently to be of great importance in predicting rotor system behavior. A computer program that solves the Reynolds equation for the above conditions will be described and sample calculation results presented.

scholarly journals Squeeze Film Dampers Executing Small Amplitude Circular-Centered Orbits in High-Speed Turbomachinery

2016 ◽  
Vol 2016 ◽  
pp. 1-16 ◽  
Author(s):  
Sina Hamzehlouia ◽  
Kamran Behdinan
Keyword(s):  
Pressure Distribution ◽  
Small Amplitude ◽  
High Speed ◽  
Fluid Film ◽  
Distribution Model ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Inertia Effects ◽  
Squeeze Film Dampers ◽  
Reaction Forces

This work represents a pressure distribution model for finite length squeeze film dampers (SFDs) executing small amplitude circular-centered orbits (CCOs) with application in high-speed turbomachinery design. The proposed pressure distribution model only accounts for unsteady (temporal) inertia terms, since based on order of magnitude analysis, for small amplitude motions of the journal center, the effect of convective inertia is negligible relative to unsteady (temporal) inertia. In this work, the continuity equation and the momentum transport equations for incompressible lubricants are reduced by assuming that the shapes of the fluid velocity profiles are not strongly influenced by the inertia forces, obtaining an extended form of Reynolds equation for the hydrodynamic pressure distribution that accounts for fluid inertia effects. Furthermore, a numerical procedure is represented to discretize the model equations by applying finite difference approximation (FDA) and to numerically determine the pressure distribution and fluid film reaction forces in SFDs with significant accuracy. Finally, the proposed model is incorporated into a simulation model and the results are compared against existing SFD models. Based on the simulation results, the pressure distribution and fluid film reaction forces are significantly influenced by fluid inertia effects even at small and moderate Reynolds numbers.

Response of a Squeeze Film Damper-Elastic Structure System to Multiple and Consecutive Impact Loads

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Luis San Andrés ◽  
Sung-Hwa Jeung
Keyword(s):  
Transient Response ◽  
Damping Ratio ◽  
Test System ◽  
Elastic Structure ◽  
Squeeze Film ◽  
Radial Clearance ◽  
System Response ◽  
Fluid Inertia ◽  
Squeeze Film Dampers ◽  
Structural Isolation

Squeeze film dampers (SFDs) are common in aircraft gas turbine engines, customized to provide a desired level of damping while also ensuring structural isolation. This paper presents measurements obtained in a test rig composed of a massive cartridge, an elastic structure, and an open-ends SFD with length L = 25.4 mm, diameter D = 127 mm, and radial clearance c = 0.267 mm. ISO VG 2 oil at room temperature lubricates the thin film. The measurements quantify the system transient response to sudden loads for motions departing from various static eccentricity displacements, es/c = 0–0.6. The batch of tests include recording the system response to (a) one single impact, (b) two (and three) impacts with an elapsed time of 30 ms in between, and (c) two or more consecutive impacts, without any delay, each with a load magnitude at 50% of the preceding impact. The load actions intend to reproduce, for example, a hard landing on an uneven surface or plunging motions from sudden contacts in a machine tool. The test system transient responses due to one or more impacts, each 30 ms apart, show the peak amplitude of motion (ZMAX) is proportional to the magnitude of applied load (FMAX). The identified system damping ratio (ξ) is proportional to the peak dynamic displacement as a linear system would show. Predictions of transient response from a physical SFD model accounting for fluid inertia correlate best with the experimental results as they produce greatly reduced peak dynamic motions when compared to predictions from a purely viscous SFD model. For the responses due to consecutive impacts, one after the other with no delay, the system motion does not decay immediately but builds to produce larger motion amplitudes than in the earlier cases. Eventually, as expected, after several oscillations, the system comes to rest. For an identical damper having a smaller clearance cs = 0.213 mm (0.8c), its damping ratio (ξs) is ∼1.3 to ∼1.7 times greater than the damping ratio for the damper with a larger film clearance (ξ). Hence, the experimentally derived (ξs/ξ) scales with (c/cs)2. The finding demonstrates the importance of manufacturing precisely the components in a damper to produce an accurate clearance.

scholarly journals Effects of Fluid Inertia and Turbulence on the Force Coefficients for Squeeze Film Dampers

1986 ◽  
Vol 108 (2) ◽  
pp. 332-339 ◽  
Author(s):  
L. San Andre´s ◽  
J. M. Vance
Keyword(s):  
Squeeze Film ◽  
Fluid Inertia ◽  
High Eccentricity ◽  
Small Eccentricity ◽  
Inertia Effects ◽  
Force Coefficients ◽  
Inertia Coefficient ◽  
Squeeze Film Dampers ◽  
Order Of Magnitude ◽  
Large Eccentricity

The effects of fluid inertia and turbulence on the force coefficients of squeeze film dampers are investigated analytically. Both the convective and the temporal terms are included in the analysis of inertia effects. The analysis of turbulence is based on friction coefficients currently found in the literature for Poiseuille flow. The effect of fluid inertia on the magnitude of the radial direct inertia coefficient (i.e., to produce an apparent “added mass” at small eccentricity ratios, due to the temporal terms) is found to be completely reversed at large eccentricity ratios. The reversal is due entirely to the inclusion of the convective inertia terms in the analysis. Turbulence is found to produce a large effect on the direct damping coefficient at high eccentricity ratios. For the long or sealed squeeze film damper at high eccentricity ratios, the damping prediction with turbulence included is an order of magnitude higher than the laminar solution.

Experimental Rotordynamic Force Coefficients for a Diffusion Bonded Compliant Hybrid Journal Gas Bearing Utilizing Fluid-Filled Hermetic Dampers

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Keith Gary ◽  
Bugra Ertas
Keyword(s):  
Dynamic Testing ◽  
Companion Paper ◽  
Squeeze Film ◽  
Dynamic Force ◽  
Force Coefficients ◽  
Squeeze Film Dampers ◽  
Lower Excitation ◽  
Excitation Frequencies ◽  
Gas Bearing ◽  
Asme Paper

Abstract Dynamic force coefficients are presented from experimental results of a radial gas bearing with hermetically sealed squeeze film dampers (HSFDs) in the bearing support. HSFDs are a relatively new technology aimed to increase damping levels in gas bearings while sustaining an oil-free bearing sump. Past HSFD designs proved bulky and contained many components making it difficult to employ in size-limited environments such as jet engines, while the diffusion bonded bearing discussed in this paper provides a compact integral design. Details of the design are found in a companion paper by Ertas (Ertas, B. H., 2019, “Compliant Hybrid Gas Bearing Using Integral Hermetically-Sealed Squeeze Film Dampers,” ASME Paper No. GT2018-76312). Test results for a 3 in. (76.2 mm) diameter bearing using a test rig providing static loads up to 80 lbs (356 N), controlled-dynamic orbital motion, and speeds up to 27 krpm are shown. Results include frequency- and speed-dependent direct and cross-coupled rotordynamic force coefficients. Dynamic testing showed little dependence on rotor speed or static load and exhibited frequency dependency at lower excitation frequencies. Cross-coupled terms are generally an order of magnitude lower than direct terms. Results show the direct stiffness coefficients increasing with frequency, while direct damping decays radically with frequency. Comparison of the overall gas bearing coefficients with the companion paper (Ertas, B. H., 2019, “Compliant Hybrid Gas Bearing Using Integral Hermetically-Sealed Squeeze Film Dampers,” ASME Paper No. GT2018-76312), showing bearing support coefficients, reveals a drastic reduction in damping when engaging the gas film. The results also indicate that the bearing can withstand vibration levels representative of a large rotor system critical speed at lower excitation frequencies.

Effects of Fluid Inertia on Finite-Length Squeeze-Film Dampers

1987 ◽  
Vol 30 (3) ◽  
pp. 384-393 ◽  
Author(s):  
L. A. San Andres ◽  
J. M. Vance
Keyword(s):  
Finite Length ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Squeeze Film Dampers

Experimental Pressures and Film Forces in a Squeeze Film Damper

1993 ◽  
Vol 115 (1) ◽  
pp. 134-140 ◽  
Author(s):  
G. L. Arauz ◽  
L. A. San Andres
Keyword(s):  
Tangential Force ◽  
Radial Force ◽  
Squeeze Film ◽  
Radial Clearance ◽  
Fluid Inertia ◽  
Damping Force ◽  
Inertia Effects ◽  
Squeeze Film Dampers ◽  
Tangential Forces ◽  
Lubricant Viscosity

The effect of whirl frequency and lubricant viscosity on the dynamic pressures and force response of an open end and a partially sealed squeeze film dampers (SFD) with a radial clearance of 0.38 mm is determined experimentally. The experiments are carried out in a damper test rig executing circular centered orbits and for whirl frequencies ranging from 33 to 83 Hz. The experimental results show that the sealed SFD configuration produces larger tangential forces than the open end SFD. The tangential (damping) force increases linearly with increasing whirl frequency. For this radial clearance fluid inertia effects in the damper are found to be negligible since the squeeze film Reynolds number is less than 1.20. Cavitation was observed in both damper configurations at high frequencies and high lubricant viscosities. This condition limited the rate of increment of the damping (tangential) force with increasing frequency and reduced the radial force when lubricant viscosity increased.

Observations on the Nonlinear Fluid Forces in Short Cylindrical Squeeze Film Dampers

1993 ◽  
Vol 115 (4) ◽  
pp. 692-698 ◽  
Author(s):  
J. Zhang ◽  
J. Ellis ◽  
J. B. Roberts
Keyword(s):  
Theoretical Work ◽  
Squeeze Film ◽  
Navier Stokes ◽  
Fluid Inertia ◽  
Navier Stokes Equation ◽  
Fluid Forces ◽  
Recent Theoretical Work ◽  
Starting Point ◽  
Squeeze Film Dampers ◽  
Inertia Forces

Recent theoretical work by Tichy and Bou-Said (1991) and El-Shafei and Crandall (1991) has resulted in new theoretical expressions for the nonlinear inertia forces for both short and long cylindrical squeeze film dampers (SFDs). This paper provides alternative derivations for the short cylindrical SFD using as a starting point a simplified two-dimensional Navier-Stokes equation. The resulting expressions for the fluid inertia forces are similar to the Tichy and Bou-Said/El-Shafei and Crandall expressions except for differences in certain numerical constants which can be explained by the different averaging methods used within the squeeze-film thickness. The analyses give additional insight into the temporal and convective origins of the various coefficients. The theoretical results are compared with published theoretical and experimental work involving nonlinear cylindrical SFD behavior. The paper highlights the importance of convective inertia terms when cylindrical SFDs operate at large values of eccentricity ratio.

The Effect of Fluid Inertia in Squeeze Film Damper Bearings: A Heuristic and Physical Description

1983 ◽  
Author(s):  
John A. Tichy
Keyword(s):  
Hydrodynamic Lubrication ◽  
Turbulence Models ◽  
Squeeze Film ◽  
Squeezing Flow ◽  
Fluid Inertia ◽  
Inertia Effects ◽  
Practical Applications ◽  
Viscous Forces ◽  
Squeeze Film Dampers ◽  
Inertia Forces

Fluid inertia forces are comparable to viscous forces in squeeze film dampers in the range of many practical applications. This statement appears to contradict the commonly held view in hydrodynamic lubrication that inertia effects are small. Upon closer inspection, the latter is true for predominantly sliding (rather than squeezing) flow bearings. The basic equations of hydrodynamic lubrication flow are developed, including the inertia terms. The appropriate orders of magnitude of the viscous and inertia terms are evaluated and compared, for journal bearings and for squeeze film dampers. Exact equations for various limiting cases are presented: low eccentricity, high and low Reynolds number. The asymptotic behavior is surprisingly similar in all cases. Due to inertia, the damper force may shift 90° forward from its purely viscous location. Inertia forces are evaluated for typical damper conditions. The effect of turbulence in squeeze film dampers is also discussed. On physical grounds it is argued that the transition occurs at much higher Reynolds numbers than the usual lubrication turbulence models predict.

Sign in / Sign up

Export Citation Format

Share Document