Non-Newtonian Elastohydrodynamic Lubrication of Point Contact

1991 ◽  
Vol 113 (4) ◽  
pp. 703-711 ◽  
Author(s):  
Kyung Hoon Kim ◽  
Farshid Sadeghi
Keyword(s):  
Film Thickness ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Two Dimensional ◽  
Point Contacts ◽  
Dimensionless Velocity ◽  
Simultaneous System ◽  
Elasticity Equations ◽  
Minimum Film Thickness ◽  
Pressure Spike

A numerical solution to the problem of isothermal non-Newtonian elastohydrodynamic lubrication of rolling/sliding point contacts has been obtained. The multigrid technique is used to solve the simultaneous system of two-dimensional modified Reynolds and elasticity equations. The effects of various loads, speeds, and slide to roll ratios on the pressure distribution, film thickness, and friction force have been investigated. Results for the dimensionless load W = 4.6 × 10−6 and 1.1 × 10−6, and the dimensionless velocity U = 3 × 10−10 and 3 × 10−11 are presented. The results indicate that slide to roll ratio has negligible effect on the minimum film thickness, however, it significantly reduces the pressure spike.

Multigrid, an Alternative Method of Solution for Two-Dimensional Elastohydrodynamically Lubricated Point Contact Calculations

1987 ◽  
Vol 109 (3) ◽  
pp. 437-443 ◽  
Author(s):  
A. A. Lubrecht ◽  
W. E. ten Napel ◽  
R. Bosma
Keyword(s):  
Film Thickness ◽  
Iterative Methods ◽  
Multigrid Method ◽  
Computing Time ◽  
Point Contact ◽  
Two Dimensional ◽  
Point Contacts ◽  
Pressure Profiles ◽  
Minimum Film Thickness ◽  
Method Of Solution

Detailed and accurate film thickness and pressure profiles have been calculated for point contacts at moderate and high loads, using a multigrid method. The influence of the compressibility of the lubricant and of the number of nodal points on the calculated minimum film thickness and maximum spike pressure have been examined. The required computing time is two orders of magnitude less, compared with the calculations using “classical” iterative methods.

Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part IV—Starvation Results

1977 ◽  
Vol 99 (1) ◽  
pp. 15-23 ◽  
Author(s):  
B. J. Hamrock ◽  
D. Dowson
Keyword(s):  
Film Thickness ◽  
Numerical Procedure ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
Contact Center ◽  
Minimum Film Thickness ◽  
Pressure Spike ◽  
Contour Plots

Utilizing the theory and numerical procedure developed by the authors in an earlier publication the influence of lubricant starvation on minimum film thickness was investigated. This study of lubricant starvation was performed simply by moving the inlet boundary closer to the contact center. From the results it was found that for the range of conditions considered the value of dimensionless inlet distance at the boundary between fully flooded and starved conditions (m*) can be expressed simply as m*=1+3.06Rxb2Hc,F0.58 or m*=1+3.34Rxb2Hmin,F0.56 that is, for a dimensionless inlet distance (m) less than m*, starvation occurs, and for m ≥ m*, a fully flooded condition exists. Furthermore, it has been possible to express the central and minimum film thickness for a starved condition as Hc,S=Hc,Fm−1m*−10.29Hmin,S=Hmin,Fm−1m*−10.25 Contour plots of the pressure and film thickness in and around the contact are shown for the fully flooded and starved lubricant condition. From these contour plots it was observed that the pressure spike becomes suppressed and the film thickness decreases substantially as starvation increases.

scholarly journals A thermal resistances-based approach for thermal-elastohydrodynamic calculations in point contacts

2017 ◽  
Vol 232 (11) ◽  
pp. 2088-2102 ◽  
Author(s):  
Eduardo de la Guerra Ochoa ◽  
Javier Echávarri Otero ◽  
Enrique Chacón Tanarro ◽  
Benito del Río López
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Thermal Effects ◽  
Good Accuracy ◽  
Computational Cost ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
New Approach ◽  
Ball On Disc

This article presents a thermal resistances-based approach for solving the thermal-elastohydrodynamic lubrication problem in point contact, taking the lubricant rheology into account. The friction coefficient in the contact is estimated, along with the distribution of both film thickness and temperature. A commercial tribometer is used in order to measure the friction coefficient at a ball-on-disc point contact lubricated with a polyalphaolefin base. These data and other experimental results available in the bibliography are compared to those obtained by using the proposed methodology, and thermal effects are analysed. The new approach shows good accuracy for predicting the friction coefficient and requires less computational cost than full thermal-elastohydrodynamic simulations.

Theoretical and experimental studies of the oil film in lubricated point contact

1966 ◽  
Vol 291 (1427) ◽  
pp. 520-536 ◽  
Keyword(s):  
Surface Layer ◽  
Film Thickness ◽  
Strong Evidence ◽  
Experimental Studies ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Experimental Results ◽  
Point Contacts ◽  
Previous Theory ◽  
Oil Film

A technique using Newton’s rings for mapping the oil film of lubricated point contacts is described. A theoretical value for the film thickness of such contacts in elastohydrodynamic lubrication is derived. The experimental results give the exit constriction predicted by previous theory but never shown in detail. The comparison of theoretical and experimental oil film thicknesses, which is satisfactorily accurate, gives strong evidence for a viscous surface layer some 1000Å thick. This film agrees with the known ‘lubricating power’ of the various oils tested.

Roughness Amplitude Reduction Under Non-Newtonian EHL Conditions

2005 ◽  
Author(s):  
A. D. Chapkov ◽  
C. H. Venner ◽  
A. A. Lubrecht
Keyword(s):  
Film Thickness ◽  
Pressure Fluctuations ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Quantitative Prediction ◽  
Point Contacts ◽  
Minimum Film Thickness ◽  
Roughness Amplitude ◽  
Average Film Thickness ◽  
Ehl Contact

The influence of surface roughness on the performance of bearings and gears operating under ElastoHydrodynamic Lubrication (EHL) conditions has become increasingly important over the last decade, as the average film thickness decreased due to various influences. Surface features can reduce the minimum film thickness and thus increase the wear. They can also increase the temperature and the pressure fluctuations, which directly affects the component life. In order to describe the roughness geometry inside an EHL contact, the amplitude reduction of harmonic waviness has been studied over the last ten years. This theory currently allows a quantitative prediction of the waviness amplitude and includes the influence of wavelength and contact operating conditions. However, the model assumes a Newtonian behaviour of the lubricant. The current paper makes a first contribution to the extension of the roughness amplitude reduction for EHL point contacts including non-Newtonian effects.

An Experimental Evaluation of the Hamrock and Dowson Minimum Film Thickness Equation for Fully Flooded EHD Point Contacts

1981 ◽  
Vol 103 (2) ◽  
pp. 284-294 ◽  
Author(s):  
K. A. Koye ◽  
W. O. Winer
Keyword(s):  
Experimental Data ◽  
Statistical Analysis ◽  
Film Thickness ◽  
Experimental Evaluation ◽  
Point Contact ◽  
Major Axis ◽  
Point Contacts ◽  
Lubricant Film Thickness ◽  
Minimum Film Thickness ◽  
Ellipticity Ratio

Fifty-seven measurements of the minimum lubricant film thickness separating the elastohydrodynamically lubricated point contact of a steel crowned roller and a flat sapphire disk were made by an optical interferometry technique. The data collected were used to evaluate the Hamrock and Dowson minimum EHD film thickness model over a practical range of contact ellipticity ratio where the major axis of the contact ellipse is aligned both parallel and perpendicular to the direction of motion. A statistical analysis of the measured film thickness data showed that the experimental data averaged 30 percent greater film thickness than the Hamrock and Dowson model predicts.

Effect of Stiff Coatings on EHL Film Thickness in Point Contacts

2007 ◽  
Author(s):  
Yuchuan Liu ◽  
Q. Jane Wang ◽  
Dong Zhu
Keyword(s):  
Film Thickness ◽  
Working Conditions ◽  
Coating Thickness ◽  
Point Contact ◽  
Thickness Variation ◽  
Point Contacts ◽  
Lubricant Film Thickness ◽  
Wide Range ◽  
Minimum Film Thickness ◽  
Coating Material Properties

This study investigates the influences of coating material properties and coating thickness on lubricant film thickness based on a point-contact isothermal EHL model developed recently by the authors. The results present the trend of minimum film thickness variation as a function of coating thickness and elastic modulus under a wide range of working conditions. Numerical results indicates that the increase in minimum film thickness, Imax, and the corresponding optimal dimensionless coating thickness, H2, can be expressed in the following formulas: Imax=0.766M0.0248R20.0296L0.1379exp(−0.0245ln2L)H2=0.049M0.4557R2−0.1722L0.7611exp(−0.0504ln2M−0.0921ln2L) These formulas can be used to estimate the effect of a coating on EHL film thickness.

Effect of changing geometrical characteristics for different shapes of a single ridge passing through elastohydrodynamic of point contacts

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mohamed Abd Alsamieh
Keyword(s):  
Film Thickness ◽  
Pressure Distribution ◽  
Reynolds Equation ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
Time Step ◽  
Content Type ◽  
Geometrical Characteristics ◽  
Different Shapes

Purpose The purpose of this paper is to study the behavior of a single ridge passing through elastohydrodynamic lubrication of point contacts problem for different ridge shapes and sizes, including flat-top, triangular and cosine wave pattern to get an optimal ridge profile. Design/methodology/approach The time-dependent Reynolds’ equation is solved using Newton–Raphson technique. Several shapes of surface feature are simulated and the film thickness and pressure distribution are obtained at every time step by simultaneous solution of the Reynolds’ equation and film thickness equation, including elastic deformation. Film thickness and pressure distribution are chosen to be the criteria in the comparisons. Findings The geometrical characteristics of the ridge play an important role in the formation of lubricant film thickness profile and the pressure distribution through the contact zone. To minimize wear, friction and fatigue life, an optimal ridge profile should have smooth shape with small ridge size. Obtained results are compared with other published numerical results and show a good agreement. Originality/value The study evaluates the performance of different surface features of a single ridge with different shapes and sizes passing through elastohydrodynamic of point contact problem in relation to film thickness and pressure profile.

Debris Effects on EHL Contact

2000 ◽  
Vol 122 (4) ◽  
pp. 711-720 ◽  
Author(s):  
Young S. Kang ◽  
Farshid Sadeghi ◽  
Xiaolan Ai
Keyword(s):  
Film Thickness ◽  
Reynolds Equation ◽  
Elastohydrodynamic Lubrication ◽  
Force Balance ◽  
Time Dependent ◽  
Elasticity Equations ◽  
Minimum Film Thickness ◽  
Bounding Surfaces ◽  
Force Balance Equation ◽  
Ehl Contact

A model was developed to study the effects of a rigid debris on elastohydrodynamic lubrication of rolling/sliding contacts. In order to achieve the objectives the time dependent Reynolds equation was modified to include the effects of an ellipsoidal shaped debris. The modified time dependent Reynolds and elasticity equations were simultaneously solved to determine the pressure and film thickness in EHL contacts. The debris force balance equation was solved to determine the debris velocity. The model was then used to obtain results for a variety of loads, speeds, and debris sizes. The results indicate that the debris has a significant effect on the pressure distribution and causes a dent on the rolling/sliding bounding surfaces. Depending on the size and location of the debris the pressure generated within the contact can be high enough to plastically deform the bounding surfaces. Debris smaller than the minimum film thickness do not enter the contact and only large and more spherical debris move toward the contact. [S0742-4787(11)00501-7]

Occurrence of High Pressure Spike in Unidirectional Start–Stop–Start Point Contacts

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
P. Sperka ◽  
J. Wang ◽  
I. Krupka ◽  
M. Hartl ◽  
M. Kaneta
Keyword(s):  
High Pressure ◽  
Film Thickness ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Elastohydrodynamic Lubrication ◽  
Rolling Contact ◽  
Point Contacts ◽  
Pressure Distributions ◽  
Machine Element ◽  
Pressure Spike

The transient film thickness and pressure distributions in point elastohydrodynamic lubrication (EHL) contacts during start–stop–start motion are discussed based on experimental and numerical analyses. When the machine element starts to move after the stopping, where the oil is entrapped between two surfaces, the pressure at the exit area increases very much. The pressure increase depends markedly on the overall film thickness before the stopping of the motion, but is hardly controlled by the acceleration after the stopping. It can be considered that this phenomenon affects the rolling contact fatigue damage.

Sign in / Sign up

Export Citation Format

Share Document