Adhesion of Contacting Rough Surfaces in the Presence of Sub-Boundary Lubrication

1990 ◽  
Vol 112 (1) ◽  
pp. 98-104 ◽  
Author(s):  
H. M. Stanley ◽  
I. Etsion ◽  
D. B. Bogy
Keyword(s):  
Film Thickness ◽  
Boundary Lubrication ◽  
Critical Thickness ◽  
Rough Surfaces ◽  
Thin Layers ◽  
Solid Surfaces ◽  
High Affinity ◽  
Wide Range ◽  
Adhesion Model ◽  
Very High

An improved DMT adhesion model is used in conjunction with an elastoplastic contact model to analyze the adhesion of contacting rough solid surfaces covered with extremely thin layers of a lubricant having a very high affinity for the surfaces. This we call sub-boundary lubrication. The paper investigates the effects of the solid surface topography and the film thickness of the lubricant on the adhesion and pull-off forces. A roughness-dependent critical thickness phenomenon is predicted: very rough surfaces may exhibit low adhesion for a wide range of lubricant thicknesses, while for smooth surfaces adhesion may increase dramatically even for a film thickness t below the standard deviation of surface heights σ. The increased adhesion could cause the surfaces to stick together to the extent that sensitive tribological systems may be damaged.

Critical Thickness of Surface Film in Boundary Lubrication

1956 ◽  
Vol 23 (3) ◽  
pp. 458-460
Author(s):  
I-Ming Feng ◽  
C. M. Chang
Keyword(s):  
Film Thickness ◽  
Boundary Lubrication ◽  
Critical Thickness ◽  
Surface Film ◽  
Critical Value ◽  
Rapid Decrease ◽  
Experimental Results ◽  
Equivalent Thickness ◽  
Pure Metals

Abstract When the combined equivalent thickness of the surface film approaches and finally becomes greater than the critical value, the weakening of the interlocking effect of the plastic roughening results in rapid decrease in wear and ultimately reduces wear to practically zero. This is verified by experimental results of wear of pure metals with controlled surface film thickness in the region near the critical thickness.

Adhesion Model for Metallic Rough Surfaces

1988 ◽  
Vol 110 (1) ◽  
pp. 50-56 ◽  
Author(s):  
W. R. Chang ◽  
I. Etsion ◽  
D. B. Bogy
Keyword(s):  
Surface Roughness ◽  
Surface Energy ◽  
Adhesion Force ◽  
Rough Surfaces ◽  
Contact Model ◽  
External Loading ◽  
Elastic Plastic ◽  
Adhesion Model ◽  
Very High

An improved DMT adhesion model in conjunction with an elastic-plastic contact model is used to study adhesion of contacting metallic rough surfaces. The effects of surface roughness and surface energy of adhesion on the pull-off force and on the significance of the adhesion force are investigated. It is shown that for clean surfaces the adhesion is quite large even for relatively rough surfaces. Adhesion is negligible only for contaminated rough surfaces or at very high external loading.

A multi-beam intensity-based approach for lubricant film measurements in non-conformal contacts

2002 ◽  
Vol 216 (5) ◽  
pp. 281-291 ◽  
Author(s):  
F Guo ◽  
P. L. Wong
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Steel Ball ◽  
Thin Layers ◽  
Beam Intensity ◽  
Lubricant Layer ◽  
Test Technique ◽  
Glass Disc ◽  
Wide Range

Studies of elastohydrodynamic lubrication (EHL) frequently utilize the phenomenon of optical interference which is exhibited when an illuminated steel ball is in contact with a partially Cr-coated glass disc in conjunction with a lubricant layer of known refractive index. The use of the steel and chromium surfaces enables lubricants having similar refractive indices to glass to be examined. The EHL contact is composed of two microscopically thin layers: the Cr coating and the lubricant film, bounded by the glass disc and the steel ball. That the two-beam interference method frequently used in optical EHL research may induce significant errors in the measurement of film thickness is reported in this paper. A theoretical analysis which includes consideration of the effects of both multi-beam interference and optical absorption within the Cr film and the steel surface is presented. The analysis is used to devise a multi-beam intensity-based test technique which has been validated for a wide range of lubricant film thickness measurements at a resolution of 1 nm and offers a practical minimum detectable film thickness as thin as 1 nm.

On the Stribeck Curves for Lubricated Counterformal Contacts of Rough Surfaces

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Dong Zhu ◽  
Jiaxu Wang ◽  
Q. Jane Wang
Keyword(s):  
Film Thickness ◽  
Numerical Solutions ◽  
Rough Surfaces ◽  
Elastohydrodynamic Lubrication ◽  
Real Data ◽  
Operating Conditions ◽  
Stribeck Curve ◽  
Flash Temperature ◽  
Wide Range ◽  
Stribeck Curves

The “Stribeck curve” is a well-known concept, describing the frictional behavior of a lubricated interface during the transition from boundary and mixed lubrication up to full-film hydrodynamic/elastohydrodynamic lubrication. It can be found in nearly every tribology textbook/handbook and many articles and technical papers. However, the majority of the published Stribeck curves are only conceptual without real data from either experiments or numerical solutions. The limited number of published ones with real data is often incomplete, covering only a portion of the entire transition. This is because generating a complete Stribeck curve requires experimental or numerical results in an extremely wide range of operating conditions, which has been a great challenge. Also, numerically calculating a Stribeck curve requires a unified model with robust algorithms that is capable of handling the entire spectrum of lubrication status. In the present study, numerical solutions in counterformal contacts of rough surfaces are obtained by using the unified deterministic mixed elastohydrodynamic lubrication (EHL) model recently developed. Stribeck curves are plotted in a wide range of speed and lubricant film thickness based on the simulation results with various types of contact geometry using machined rough surfaces of different orientations. Surface flash temperature is also analyzed during the friction calculation considering the mutual dependence between friction and interfacial temperature. Obtained results show that in lubricated concentrated contacts, friction continuously decreases as speed and film thickness increase even in the full-film regime until extremely high speeds are reached. This is mainly due to the reduction of lubricant limiting shear stress caused by flash temperature rise. The results also reveal that contact ellipticity and roughness orientation have limited influence on frictional behaviors, especially in the full-film and boundary lubrication regimes.

TEM study of boron additions to cobalt aluminide

1988 ◽  
Vol 46 ◽  
pp. 546-547
Author(s):  
Gerald B. Feldewerth
Keyword(s):  
High Temperature ◽  
Turbine Engines ◽  
Major Drawback ◽  
University Of Missouri ◽  
Specific Strength ◽  
Aerospace Applications ◽  
Wide Range ◽  
Ordered Alloys ◽  
The University ◽  
Very High

In recent years an increasing emphasis has been placed on the study of high temperature intermetallic compounds for possible aerospace applications. One group of interest is the B2 aiuminides. This group of intermetaliics has a very high melting temperature, good high temperature, and excellent specific strength. These qualities make it a candidate for applications such as turbine engines. The B2 aiuminides exist over a wide range of compositions and also have a large solubility for third element substitutional additions, which may allow alloying additions to overcome their major drawback, their brittle nature.One B2 aluminide currently being studied is cobalt aluminide. Optical microscopy of CoAl alloys produced at the University of Missouri-Rolla showed a dramatic decrease in the grain size which affects the yield strength and flow stress of long range ordered alloys, and a change in the grain shape with the addition of 0.5 % boron.

Effects of Heparin Oligosaccharides with High Affinity for Antithrombin III in Experimental Venous Thrombosis

1982 ◽  
Vol 47 (03) ◽  
pp. 244-248 ◽  
Author(s):  
D P Thomas ◽  
Rosemary E Merton ◽  
T W Barrowcliffe ◽  
L Thunberg ◽  
U Lindahl
Keyword(s):  
Antithrombin Iii ◽  
Specific Activity ◽  
High Specific Activity ◽  
Factor Xa ◽  
Blood Levels ◽  
Thrombin Time ◽  
High Affinity ◽  
Very High

SummaryThe in vitro and in vivo characteristics of two oligosaccharide heparin fragments have been compared to those of unfractionated mucosal heparin. A decasaccharide fragment had essentially no activity by APTT or calcium thrombin time assays in vitro, but possessed very high specific activity by anti-Factor Xa assays. When injected into rabbits at doses of up to 80 ¼g/kg, this fragment was relatively ineffective in impairing stasis thrombosis despite producing high blood levels by anti-Xa assays. A 16-18 monosaccharide fragment had even higher specific activity (almost 2000 iu/mg) by chromogenic substrate anti-Xa assay, with minimal activity by APTT. When injected in vivo, this fragment gave low blood levels by APTT, very high anti-Xa levels, and was more effective in preventing thrombosis than the decasaccharide fragment. However, in comparison with unfractionated heparin, the 16-18 monosaccharide fragment was only partially effective in preventing thrombosis, despite producing much higher blood levels by anti-Xa assays.It is concluded that the high-affinity binding of a heparin fragment to antithrombin III does not by itself impair venous thrombogenesis, and that the anti-Factor Xa activity of heparin is only a partial expression of its therapeutic potential.

Features of the Christian values ​​system

2004 ◽  
pp. 21-29
Author(s):  
G.V. Pyrog
Keyword(s):  
Public Opinion ◽  
Religious Beliefs ◽  
Religious Values ◽  
Direct Influence ◽  
Moral Norms ◽  
Value System ◽  
Christian Religion ◽  
Mass Consciousness ◽  
Wide Range ◽  
Very High

In domestic scientific and public opinion, interest in religion as a new worldview paradigm is very high. Today's attention to the Christian religion in our society is connected, in our opinion, with the specificity of its value system, which distinguishes it from other forms of consciousness: the idea of ​​God, the absolute, the eternity of moral norms. That is why its historical forms do not receive accurate characteristics and do not matter in the mass consciousness. Modern religious beliefs do not always arise as a result of the direct influence of church preaching. The emerging religious values ​​are absorbed in a wide range of philosophical, artistic, ethical ideas, acting as a compensation for what is generally defined as spirituality. At the same time, the appeal to Christian values ​​became very popular.

DURCOMET 100

Alloy Digest ◽  
1993 ◽  
Vol 42 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Mechanical Strength ◽  
Heat Treating ◽  
Corrosion And Wear ◽  
Annealed Condition ◽  
Excellent Corrosion Resistance ◽  
Wide Range ◽  
Very High

Abstract Durcomet 100 is an improved version of Alloy CD-4 MCu with better corrosion and wear resistance. The alloy is used in the annealed condition and possesses excellent corrosion resistance over a wide range of corrosion environments. Mechanical strength is also very high. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating and joining. Filing Code: SS-540. Producer or source: Duriron Company Inc.

Influencia de las condiciones de secado solar en la coloración de plantas medicinales

2019 ◽  
pp. 28-34
Author(s):  
Margarita Castillo-Téllez ◽  
Beatriz Castillo-Téllez ◽  
Juan Carlos Ovando-Sierra ◽  
Luz María Hernández-Cruz
Keyword(s):  
Medicinal Plants ◽  
Forced Convection ◽  
Rural Areas ◽  
Color Change ◽  
Drying Process ◽  
Scientific Medicine ◽  
Drying Time ◽  
Bacterial Proliferation ◽  
Wide Range ◽  
Very High

For millennia, humans have used hundreds of medicinal plants to treat diseases. Currently, many species with important characteristics are known to alleviate a wide range of health problems, mainly in rural areas, where the use of these resources is very high, even replacing scientific medicine almost completely. This paper presents the dehydration of medicinal plants that are grown in the State of Campeche through direct and indirect solar technologies in order to evaluate the influence of air flow and temperature on the color of the final product through the L* a* scale. b*, analyzing the activity of water and humidity during the drying process. The experimental results showed that the direct solar dryer with forced convection presents a little significant color change in a drying time of 400 min on average, guaranteeing the null bacterial proliferation and reaching a final humidity between 9 % and 11 %.

scholarly journals Separate Universe calibration of the dependence of halo bias on cosmic web anisotropy

2020 ◽  
Vol 499 (3) ◽  
pp. 4418-4431 ◽  
Author(s):  
Sujatha Ramakrishnan ◽  
Aseem Paranjape
Keyword(s):  
Dark Matter ◽  
High Precision ◽  
Gaussian Distribution ◽  
Initial Perturbation ◽  
Analytical Framework ◽  
Web Environment ◽  
Wide Range ◽  
Galaxy Assembly ◽  
Very High ◽  
Good Agreement

ABSTRACT We use the Separate Universe technique to calibrate the dependence of linear and quadratic halo bias b1 and b2 on the local cosmic web environment of dark matter haloes. We do this by measuring the response of halo abundances at fixed mass and cosmic web tidal anisotropy α to an infinite wavelength initial perturbation. We augment our measurements with an analytical framework developed in earlier work that exploits the near-lognormal shape of the distribution of α and results in very high precision calibrations. We present convenient fitting functions for the dependence of b1 and b2 on α over a wide range of halo mass for redshifts 0 ≤ z ≤ 1. Our calibration of b2(α) is the first demonstration to date of the dependence of non-linear bias on the local web environment. Motivated by previous results that showed that α is the primary indicator of halo assembly bias for a number of halo properties beyond halo mass, we then extend our analytical framework to accommodate the dependence of b1 and b2 on any such secondary property that has, or can be monotonically transformed to have, a Gaussian distribution. We demonstrate this technique for the specific case of halo concentration, finding good agreement with previous results. Our calibrations will be useful for a variety of halo model analyses focusing on galaxy assembly bias, as well as analytical forecasts of the potential for using α as a segregating variable in multitracer analyses.

Sign in / Sign up

Export Citation Format

Share Document