Leading Edge Film Cooling Heat Transfer Through One Row of Inclined Film Slots and Holes Including Mainstream Turbulence Effects

1994 ◽  
Vol 116 (3) ◽  
pp. 561-569 ◽  
Author(s):  
Shichuan Ou ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Cross Sectional ◽  
Stagnation Line ◽  
Blowing Ratio ◽  
Test Models ◽  
Turbulence Effects

The effects of film opening shape and mainstream turbulence on the leading edge heat transfer coefficient and film effectiveness were experimentally investigated. The experiments were performed using test models with a semi-cylindrical leading edge and a flat afterbody. A bar grid (Tu = 5.07 percent) and a passive grid (Tu = 9.67 percent) produced two levels of mainstream turbulence. Two separate cases of one-row injection through film slots or holes located only at ±15 deg or only at ±40 deg from the stagnation line were studied for three blowing ratios of 0.4, 0.8, and 1.2 at the Reynolds number (ReD) of 100,000. The slots in each row were spaced three cross-sectional slot lengths (P = 3l) apart, while the holes were spaced four holes diameters (P = 4d) apart. Both geometries had equal cross-sectional area and pitch. The results show that the leading edge heat transfer coefficient increases and the film effectiveness decreases with increasing blowing ratio; however, B = 0.8 provides the highest film effectiveness for the film hole with ±40 deg injection. The heat transfer coefficient increases and the film effectiveness decreases with increasing mainstream turbulence level. However, the mainstream turbulence effect on the film effectiveness is reduced as the blowing ratio is increased. Slot geometry provides better film cooling performance than the hole geometry for all test cases at the lowest blowing ratio of 0.4. However, at higher blowing ratios of 0.8 and 1.2, the reverse is true for ±40 deg injection at mainstream turbulence of 0.75 and 9.67 percent.

Influence of Mainstream Turbulence on Leading Edge Film Cooling Heat Transfer Through Two Rows of Inclined Film Slots

1992 ◽  
Vol 114 (4) ◽  
pp. 724-733 ◽  
Author(s):  
S. Ou ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Heat Load ◽  
Leading Edge ◽  
Width Ratio ◽  
Cross Sectional ◽  
Stagnation Line ◽  
Blowing Ratio

The effect of film slot injection on leading edge heat transfer coefficient and film cooling effectiveness under high mainstream turbulence conditions was experimentally studied for flow across a blunt body with a semicylinder leading edge and a flat afterbody. High mainstream turbulence levels were generated by a bar grid (Tu = 5.07 percent) and a passive grid (Tu = 9.67 percent). The incident mainstream Reynolds number based on the cylinder diameter was about 100,000. The spanwise and streamwise distributions of the heat transfer coefficient and film effectiveness in the leading edge and on the flat sidewall were obtained for three blowing ratios (B = 0.4, 0.8, and 1.2) with two rows of film slots located at ± 15 and ± 40 deg from the stagnation line. The cross-sectional slot length-to-width ratio was two. The slots in each row were spaced three cross-sectional slot lengths apart and were angled 30 and 90 deg to the surface in the spanwise and streamwise directions, respectively. The results show that heat transfer coefficient increases with increasing blowing ratio, but the film effectiveness reaches a maximum at an intermediate blowing ratio of B = 0.8 for both low (Tu = 0.75 percent) and high (Tu = 9.67 percent) mainstream turbulence conditions. The leading edge heat transfer coefficient increases and the film effectiveness decreases with mainstream turbulence level for the low blowing ratio; however, the mainstream turbulence effect decreases for the high blowing ratio. The leading edge heat load is significantly reduced with two rows of film slot injection. The blowing ratio of B = 0.4 provides the lowest heat load In the leading edge region for the low mainstream turbulence, but B = 0.8 gives the lowest heat load for the high mainstream turbulence conditions.

Influence of Mainstream Turbulence on Leading Edge Film Cooling Heat Transfer Through Two Rows of Inclined Film Slots

1991 ◽  
Author(s):  
S. Ou ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Heat Load ◽  
Leading Edge ◽  
Cross Sectional ◽  
Stagnation Line ◽  
Blowing Ratio ◽  
The Heat Transfer Coefficient

The effect of film slot injection on leading edge heat transfer coefficient and film cooling effectiveness under high mainstream turbulence conditions was experimentally studied for flow across a blunt body with a semi-cylinder leading edge and a flat afterbody. High mainstream turbulence levels were generated by a bar grid (Tu = 5.07%) and a passive grid (Tu = 9.67%). The incident mainstream Reynolds number based on the cylinder diameter was about 100,000. The spanwise and streamwise distributions of the heat transfer coefficient and film effectiveness in the leading edge and on the flat sidewall were obtained for three blowing ratios (B = 0.4, 0.8 and 1.2) with two rows of film slots located at ±15° and ±40° from stagnation line. The cross-sectional slot length-to-width ratio was two. The slots in each row were spaced three cross-sectional slot lengths apart and were angled 30° and 90° to the surface in the spanwise and streamwise direction, respectively. The results show that the heat transfer coefficient increases with increasing blowing ratio, but the film effectiveness reaches the maximum at an intermediate blowing ratio of B = 0.8 for both low (Tu = 0.75%) and high (Tu = 9.67%) mainstream turbulence conditions. The leading edge heat transfer coefficient increases and the film effectiveness decreases with mainstream turbulence level for the low blowing ratio; however, the mainstream turbulence effect reduces for the high blowing ratio. The leading edge heat load is significantly reduced with two rows of film slot injection. The blowing ratio of B = 0.4 provides the lowest heat load in the leading edge region for the low mainstream turbulence but B = 0.8 gives the lowest heat load for the high mainstream turbulence conditions.

Numerical Study on the Influence of Trench Width on Film Cooling Characteristics of Double-Wave Trench

2017 ◽  
Author(s):  
Bo-lun Zhang ◽  
Li Zhang ◽  
Hui-ren Zhu ◽  
Jian-sheng Wei ◽  
Zhong-yi Fu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Numerical Study ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Trench Width

Film cooling performance of the double-wave trench was numerically studied to improve the film cooling characteristics. Double-wave trench was formed by changing the leading edge and trailing edge of transverse trench into cosine wave. The film cooling characteristics of transverse trench and double-wave trench were numerically studied using Reynolds Averaged Navier Stokes (RANS) simulations with realizable k-ε turbulence model and enhanced wall treatment. The film cooling effectiveness and heat transfer coefficient of double-wave trench at different trench width (W = 0.8D, 1.4D, 2.1D) conditions are investigated, and the distribution of temperature field and flow field were analyzed. The results show that double-wave trench effectively improves the film cooling effectiveness and the uniformity of jet at the downstream wall of the trench. The span-wise averaged film cooling effectiveness of the double-wave trench model increases 20–63% comparing with that of the transverse trench at high blowing ratio. The anti-counter-rotating vortices which can press the film on near-wall are formed at the downstream wall of the double-wave trench. With the double-wave trench width decreasing, the film cooling effectiveness gradually reduces at the hole center-line region of the downstream trench. With the increase of the blowing ratio, the span-wise averaged heat transfer coefficient increases. The span-wise averaged heat transfer coefficient of the double-wave trench with 0.8D and 2.1D trench width is higher than that of the double-wave trench with 1.4D trench width at the high blowing ratio conditions.

Investigation on the Leading Edge Film Cooling of Counter-Inclined Cylindrical and Laid-Back Holes With and Without Impingement: Part II — Heat Transfer Coefficient

2018 ◽  
Author(s):  
Rui-dong Wang ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Hui-ren Zhu ◽  
Qi-ling Guo ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
The Heat Transfer Coefficient ◽  
Tube Structure

Heat transfer of the counter-inclined cylindrical and laid-back holes with and without impingement on the turbine vane leading edge model are investigated in this paper. To obtain the film cooling effectiveness and heat transfer coefficient, transient temperature measurement technique on complete surface based on double thermochromic liquid crystals is used in this research. A semi-cylinder model is used to model the vane leading edge which is arranged with two rows of holes. Four test models are measured under four blowing ratios including cylindrical film holes with and without impingement tube structure, laid-back film holes with and without impingement tube structure. This is the second part of a two-part paper, the first part paper GT2018-76061 focuses on film cooling effectiveness and this study will focus on heat transfer. Contours of surface heat transfer coefficient and laterally averaged result are presented in this paper. The result shows that the heat transfer coefficient on the surface of the leading edge is enhanced with the increase of blowing ratio for same structure. The shape of the high heat transfer coefficient region gradually inclines to span-wise direction as the blowing ratio increases. Heat transfer coefficient in the region where the jet core flows through is relatively lower, while in the jet edge region the heat transfer coefficient is relatively higher. Compared with cylindrical hole, laid-back holes give higher heat transfer coefficient. Meanwhile, the introduction of impingement also makes heat transfer coefficient higher compared with cross flow air intake. It is found that the heat transfer of the combination of laid-back hole and impingement tube can be very high under large blowing ratio which should get attention in the design process.

Experimental Investigation of Film Cooling Performance for a New Shaped Hole at the Leading Edge

2014 ◽  
Author(s):  
Tarek Elnady ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Stagnation Line ◽  
Cooling Performance

An experimental investigation has been performed to study the film cooling performance of a smooth expansion exit at the leading edge of a gas turbine vane. A two-dimensional cascade has been employed to measure the cooling performance of the proposed expansion using the transient Thermochromatic Liquid Crystal technique. One row of cylindrical holes, located on the stagnation line, is investigated with two expansion levels, 2d and 4d, in addition to the standard hole. The air is injected at 90° and 60° inclination angle relative to the vane surface at four blowing ratios ranging from 1 to 2 at a 0.9 density ratio. The Mach number and the Reynolds number based on the cascade exit velocity and the axial chord are 0.23 and 1.4E5, respectively. The detailed local heat transfer coefficient over both the pressure side and the suction side are presented in addition to the lateral-averaged normalized heat transfer coefficient. The proposed expansion provides a lower heat transfer coefficient compared with the standard cylindrical hole over the investigated blowing ratios. Combining the heat transfer coefficient with the corresponding cooling effectiveness, previously presented, the smooth expansion shows a significant reduction in the heat load with more uniform distribution of the coolant over the leading edge region. The strong confrontation between the coolant jet and the mainstream, in case of 90° injection, yields a strong dispersion of the coolant with higher heat transfer coefficient and high thermal load over the vane surface.

Film Cooling Parameter Waveforms on a Turbine Blade Leading Edge Model With Oscillating Stagnation Line

2016 ◽  
Vol 138 (7) ◽  
Author(s):  
James L. Rutledge ◽  
Tylor C. Rathsack ◽  
Matthew T. Van Voorhis ◽  
Marc D. Polanka
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Stagnation Line ◽  
Inverse Heat Transfer ◽  
Adiabatic Effectiveness ◽  
Blade Leading Edge

It is necessary to understand how film cooling influences the external convective boundary condition involving both the adiabatic wall temperature and the heat transfer coefficient in order to predict the thermal durability of a gas turbine hot gas path component. Most studies in the past have considered only steady flow, but studies of the unsteadiness naturally present in turbine flow have become more prevalent. One source of unsteadiness is wake passage from upstream components which can cause fluctuations in the stagnation location on turbine airfoils. This in turn causes unsteadiness in the behavior of the leading edge coolant jets and thus fluctuations in both the adiabatic effectiveness and heat transfer coefficient. The dynamics of h and η are now quantifiable with modern inverse heat transfer methods and nonintrusive infrared thermography. The present study involved the application of a novel inverse heat transfer methodology to determine time-resolved adiabatic effectiveness and heat transfer coefficient waveforms on a simulated turbine blade leading edge with an oscillating stagnation position. The leading edge geometry was simulated with a circular cylinder with a coolant hole located 21.5 deg downstream from the leading edge stagnation line, angled 20 deg to the surface and 90 deg to the streamwise direction. The coolant plume is shown to shift in response to the stagnation line movement. These oscillations thus influence the film cooling coverage, and the time-averaged benefit of film cooling is influenced by the oscillation.

Large Eddy Simulation of Leading Edge Film Cooling—Part II: Heat Transfer and Effect of Blowing Ratio

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Ali Rozati ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Large Eddy Simulation ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Adiabatic Effectiveness

Detailed investigation of film cooling for a cylindrical leading edge is carried out using large eddy simulation (LES). The paper focuses on the effects of coolant to mainstream blowing ratio on flow features and, consequently, on the adiabatic effectiveness and heat transfer coefficient. With the advantage of obtaining unique, accurate, and dynamic results from LES, the influential coherent structures in the flow are identified. Describing the mechanism of jet-mainstream interaction, it is shown that as the blowing ratio increases, a more turbulent shear layer and stronger mainstream entrainment occur. The combined effects lead to a lower adiabatic effectiveness and higher heat transfer coefficient. Surface distribution and span-averaged profiles are shown for both adiabatic effectiveness and heat transfer (presented by Frossling number). Results are in good agreement with the experimental data of Ekkad et al. [1998, “Detailed Film Cooling Measurement on a Cylindrical Leading Edge Model: Effect of Free-Steam Turbulence and Coolant Density,” ASME J. Turbomach., 120, pp. 799–807].

Investigations on the Film Cooling of Counter-Inclined Film-Hole Row Structures for Turbine Vane Leading Edge

2018 ◽  
Vol 35 (3) ◽  
pp. 291-303 ◽  
Author(s):  
Cun-Liang Liu ◽  
Dan Zhao ◽  
Ying-Ni Zhai ◽  
Hui-Ren Zhu ◽  
Yi-Hong He ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Blowing Ratio ◽  
Turbine Vane

AbstractNumerical simulations have been performed on the film cooling characteristics of counter-inclined structures, which have advantage in manufacturing relative to the usually used parallel-inclined film-hole row structure, on a turbine vane leading edge model. Single row structure and dual-row structure with counter-inclined film holes were applied in the simulation of leading edge film cooling of turbine vane. The effect of jet-interaction between counter-inclined film-hole rows was studied. The distributions of film cooling effectiveness and heat transfer coefficient were obtained at blowing ratios of 1.0 and 2.0. The results of single row structure show that the film cooling performances of counter-inclined film-hole row are not weakened compared to the traditional parallel-inclined film-hole row structure. The film cooling effectiveness of the counter-inclined film-hole row structure decreases with the increase of blowing ratio, while the heat transfer coefficient increases. The jet-interaction in the dual-row film cooling structure has more notable influence on the film cooling effectiveness than the heat transfer coefficient. Compared to the single row case, the interactions between the upstream counter-blowing jets and the downstream jet improve the film coverage performance and reduce the heat transfer intensity of this downstream jet under larger blowing ratio condition.

Heat Transfer Boundary Condition Waveforms on a Turbine Blade Leading Edge With Unsteady Film Cooling

2013 ◽  
Author(s):  
James L. Rutledge
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Adiabatic Wall ◽  
Time Resolved ◽  
Stagnation Line ◽  
Adiabatic Effectiveness

It is necessary to understand how film cooling both reduces the adiabatic wall temperature and influences the heat transfer coefficient in order to predict the net heat flux to a gas turbine hot gas path component. Although a great number of studies have considered steady film cooling flows, the influence of film cooling unsteadiness has only recently been considered. Unsteadiness in the freestream flow or the coolant flow can cause fluctuations in both the adiabatic effectiveness and heat transfer coefficient, the dynamics of which have been difficult to measure. In previous studies, only time averaged effects have been measured. The present study has determined time resolved adiabatic effectiveness and heat transfer coefficient waveforms using a novel inverse heat transfer methodology. Unsteady film cooling was examined on the leading edge region of a circular cylinder simulating the leading edge of a turbine blade. Unsteady interactions between h and η, were examined near a coolant hole located 21.5° downstream from the leading edge stagnation line, angled 20° to the surface and 90° to the streamwise direction. The coolant plume is shown to shift back and forth as the jet’s momentum fluctuates. Increasing freestream turbulence was found to both reduce η, and the amplitude of the η waveforms.

Influence of High Mainstream Turbulence on Leading Edge Film Cooling Heat Transfer

1992 ◽  
Vol 114 (4) ◽  
pp. 707-715 ◽  
Author(s):  
A. B. Mehendale ◽  
J. C. Han
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Blunt Body ◽  
Leading Edge ◽  
Surface Heat ◽  
Blowing Ratio ◽  
Turbulence Effect ◽  
The Heat Transfer Coefficient

The influence of high mainstream turbulence on leading edge film effectiveness and heat transfer coefficient was studied. High mainstream turbulence was produced by a passive grid and a jet grid. Experiments were performed using a blunt body with a semicylinder leading edge with a flat afterbody. The mainstream Reynolds number based on leading edge diameter was about 100,000. Spanwise and streamwise distributions of film effectiveness and heat transfer coefficient in the leading edge and on the flat sidewall were obtained for three blowing ratios, through rows of holes located at ±15 and ±40 deg from stagnation. The holes in each row were spaced three hole diameters apart and were angled 30 and 90 deg to the surface in the spanwise and streamwise directions, respectively. The results indicate that the film effectiveness decreases with increasing blowing ratio, but the reverse is true for the heat transfer coefficient. The leading edge film effectiveness for low blowing ratio (B = 0.4) is significantly reduced by high mainstream turbulence (Tu = 9.67 and 12.9 percent). The mainstream turbulence effect is diminished in the leading edge for higher blowing ratios (B = 0.8 and 1.2) but still exists on the flat sidewall region. Also, the leading edge heat transfer coefficient for blowing ratio of 0.8 increases with increasing mainstream turbulence; but the effect for other blowing ratios [B = 0.4 and 1.2) is not as systematic as for B = 0.8. Surface heat load is significantly reduced with leading edge film cooling.

Sign in / Sign up

Export Citation Format

Share Document