Corrosion of Pure Copper in Flowing Seawater Under Cavitating and Noncavitating Flow Conditions

1990 ◽  
Vol 112 (2) ◽  
pp. 218-224 ◽  
Author(s):  
R. J. K. Wood ◽  
S. A. Fry
Keyword(s):  
Steady State ◽  
Flow Field ◽  
Incubation Period ◽  
Current Distribution ◽  
Material Removal ◽  
Pure Copper ◽  
Corrosion Current ◽  
Cavitating Flow ◽  
Flow Conditions ◽  
Working Section

This paper investigates the corrosion of pure copper in flowing seawater under cavitating and non-cavitating flow conditions. Experiments were conducted in a 10 mm × 20 mm working section with a 60 deg symmetrical wedge cavitation source. A copper sidewall specimen was held under potentiostatic control and its average corrosion current was measured under different flow conditions. To facilitate a detailed investigation of the flow field upon the current distribution over the specimen surface, further tests were carried out using a sidewall incorporating 24 mini-electrodes. Apart from some indication of cavity shielding, corrosion currents were little affected by the presence of cavitation during the incubation period (when no material was being removed). However, under similar cavitation conditions (but with material removal under steady-state erosion conditions) the corrosion currents approximately doubled.

Aeroelasticity at Reversed Flow Conditions: Part 1—Numerical and Experimental Investigations of a Compressor Cascade With Controlled Vibration

2011 ◽  
Author(s):  
Harald Schoenenborn ◽  
Virginie Chenaux ◽  
Peter Ott
Keyword(s):  
Steady State ◽  
Flow Field ◽  
Unsteady Flow ◽  
Steady Flow ◽  
Experimental Investigations ◽  
Blade Surface ◽  
Flow Conditions ◽  
Steady State Flow ◽  
Reversed Flow ◽  
Blow Down

The prediction of flutter and forced response at normal flow conditions has become a standard procedure during the design of compressor airfoils. But at severe off-design conditions, the flow field becomes very complex, especially during the surge blow-down phase where reversed flow conditions occur. The correct prediction of the unsteady pressures and the resulting aerodynamic excitation or damping at these conditions remains an extremely challenging task. In the first part of the paper, basic investigations for these flow conditions are presented. Aeroelastic calculations during compressor surge are shown in the second part. Experimental investigations were performed in the Annular Test Facility for non-rotating cascades at EPF Lausanne. The test cascade was exposed to flow conditions as expected during the surge blow-down phase which is characterized by large separation regions. Measurements of the steady-state flow conditions on the blade surface, at the outer wall, upstream and downstream of the cascade provided detailed information about the steady flow conditions. The cascade was then subjected to controlled vibration of the blades with constant amplitudes and inter-blade phase angles. Unsteady pressure measurements on the blade surface and at the casing wall provided information about the resulting unsteady flow conditions. Analytical CFD calculations were performed. The steady flow field was calculated using a RANS code. Based on the steady-state flow field, unsteady calculations applying a linearized code were carried out. The agreement between measurements and calculations shows that the steady flow as well as the unsteady flow phenomena can be predicted quantitatively. In addition, knowing the blade vibration mode shape, which in this case is a torsion mode, the aerodynamic damping can be determined for the corresponding flow conditions.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Spectroscopic Techniques versus Pitot Tube for the Measurement of Flow Velocity in Narrow Ducts

Sensors ◽  
2020 ◽  
Vol 20 (24) ◽  
pp. 7349
Author(s):  
Francesco D’Amato ◽  
Silvia Viciani ◽  
Alessio Montori ◽  
Marco Barucci ◽  
Carmen Morreale ◽  
...  
Keyword(s):  
Flow Field ◽  
Flow Velocity ◽  
Pitot Tube ◽  
Optical Measurements ◽  
Trace Gas ◽  
Dual Function ◽  
Spectroscopic Techniques ◽  
Gas Composition ◽  
Flow Conditions ◽  
Theoretical Simulation

In order to assess the limits and applicability of Pitot tubes for the measurement of flow velocity in narrow ducts, e.g., biomass burning plants, an optical, dual function device was implemented. This sensor, based on spectroscopic techniques, targets a trace gas, injected inside the stack either in bursts, or continuously, so performing transit time or dilution measurements. A comparison of the two optical techniques with respect to Pitot readings was carried out in different flow conditions (speed, temperature, gas composition). The results of the two optical measurements are in agreement with each other and fit quite well the theoretical simulation of the flow field, while the results of the Pitot measurements show a remarkable dependence on position and inclination of the Pitot tube with respect to the duct axis. The implications for the metrology of small combustors’ emissions are outlined.

Fluid Flow Field in the Annulus of Boiling Water (BWR) Nuclear Reactors Under Normal and Accident Conditions

2009 ◽  
Author(s):  
Raju Ananth ◽  
Karen Fujikawa ◽  
Jay Gillis
Keyword(s):  
Fluid Flow ◽  
Velocity Field ◽  
Flow Field ◽  
Pressure Vessel ◽  
Theoretical Study ◽  
Nuclear Reactors ◽  
Boiling Water ◽  
Flow Conditions ◽  
Accident Conditions ◽  
Reactor Pressure

This paper presents a theoretical study of the velocity field in the annulus formed between the Reactor Pressure Vessel (RPV) and the shroud of a Boiling Water Reactor (BWR) under normal and accident flow conditions. Simplified geometry and an ideal irrotational flow are assumed to solve the problem using velocity potentials.

Comparison of Experimental and Numerical Simulations of Flow Within an Arterio-Venous Graft

2000 ◽  
Author(s):  
Paul F. Fischer ◽  
Seung Lee ◽  
Francis Loth ◽  
Hisham S. Bassiouny ◽  
Nurullah Arslan
Keyword(s):  
Flow Field ◽  
Steady Flow ◽  
Laser Doppler Anemometry ◽  
Transition To Turbulence ◽  
Flow Conditions ◽  
Venous Graft ◽  
Venous Anastomosis ◽  
Av Graft ◽  
Good Agreement

Abstract This was a study to compare computational and experimental results of flow field inside the venous anastomosis of an arteriovenous (AV) graft. Laser Doppler anemometry (LDA) measurements were conducted inside an upscaled end-to-side graft model under steady flow conditions at Reynolds number 1820 which is representative of the in vivo flow conditions inside a human AV graft. The distribution of the velocity and turbulence intensity was measured at several locations in the plane of the bifurcation. This flow field was simulated using computation fluid dynamics (CFD) and shown to be in good agreement. Under steady flow conditions, the flow field demonstrated an unsteady character (transition to turbulence).

Investigation on hydrodynamic forces leading to coarse particle entrainment using Large-Eddy Simulations

2021 ◽  
Author(s):  
Gaston Latessa ◽  
Angela Busse ◽  
Manousos Valyrakis
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Large Scale ◽  
Large Eddy Simulations ◽  
Flow Conditions ◽  
Mean Flow ◽  
Protection Measures ◽  
Practical Applications ◽  
Particle Entrainment ◽  
Large Eddy

<p>The prediction of particle motion in a fluid flow environment presents several challenges from the quantification of the forces exerted by the fluid onto the solids -normally with fluctuating behaviour due to turbulence- and the definition of the potential particle entrainment from these actions. An accurate description of these phenomena has many practical applications in local scour definition and to the design of protection measures.</p><p>In the present work, the actions of different flow conditions on sediment particles is investigated with the aim to translate these effects into particle entrainment identification through analytical solid dynamic equations.</p><p>Large Eddy Simulations (LES) are an increasingly practical tool that provide an accurate representation of both the mean flow field and the large-scale turbulent fluctuations. For the present case, the forces exerted by the flow are integrated over the surface of a stationary particle in the streamwise (drag) and vertical (lift) directions, together with the torques around the particle’s centre of mass. These forces are validated against experimental data under the same bed and flow conditions.</p><p>The forces are then compared against threshold values, obtained through theoretical equations of simple motions such as rolling without sliding. Thus, the frequency of entrainment is related to the different flow conditions in good agreement with results from experimental sediment entrainment research.</p><p>A thorough monitoring of the velocity flow field on several locations is carried out to determine the relationships between velocity time series at several locations around the particle and the forces acting on its surface. These results a relevant to determine ideal locations for flow investigation both in numerical and physical experiments.</p><p>Through numerical experiments, a large number of flow conditions were simulated obtaining a full set of actions over a fixed particle sitting on a smooth bed. These actions were translated into potential particle entrainment events and validated against experimental data. Future work will present the coupling of these LES models with Discrete Element Method (DEM) models to verify the entrainment phenomena entirely from a numerical perspective.</p>

CFD Leakage Predictions of Unworn and Worn Labyrinth Seals With and Without Tooth Axial Offset

2017 ◽  
Author(s):  
Hasham H. Chougule ◽  
Alexander Mirzamoghadam
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Modeling ◽  
Steady State ◽  
Flow Field ◽  
Labyrinth Seals ◽  
Small Clearance ◽  
Total Leakage ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Deflection

The objective of this study is to develop a Computational Fluid Dynamics (CFD) based methodology for analyzing and predicting leakage of worn or rub-intended labyrinth seals during operation. The simulations include intended tooth axial offset and numerical modeling of the flow field. The purpose is to predict total leakage through the seal when an axial tooth offset is provided after the intended/unintended rub. Results indicate that as expected, the leakage for the in-line worn land case (i.e. tooth under rub) is higher compared to unworn. Furthermore, the intended rotor/teeth forward axial offset/shift with respect to the rubbed land reduces the seal leakage. The overall leakage of a rubbed seal with axial tooth offset is observed to be considerably reduced, and it can become even less than a small clearance seal designed not to rub. The reduced leakage during steady state is due to a targeted smaller running gap because of tooth offset under the intended/worn land groove shape, higher blockages, higher turbulence and flow deflection as compared to worn seal model without axial tooth offset.

Drawing of Tubes

1980 ◽  
Vol 47 (4) ◽  
pp. 736-740 ◽  
Author(s):  
D. Durban
Keyword(s):  
Exact Solution ◽  
Steady State ◽  
Radial Flow ◽  
Material Behavior ◽  
Wall Friction ◽  
Flow Rule ◽  
Flow Conditions ◽  
Steady State Flow ◽  
Linear Hardening ◽  
Von Mises

The process of the tube drawing between two rough conical walls is analyzed within the framework of continuum plasticity. Material behavior is modeled as rigid/linear-hardening along with the von-Mises flow rule. Assuming a radial flow pattern and steady state flow conditions it becomes possible to obtain an exact solution for the stresses and velocity. Useful relations are derived for practical cases where the nonuniformity induced by wall friction is small. A few restrictions on the validity of the results are discussed.

The Effect of Stator-Rotor Hub Sealing Flow on the Mainstream Aerodynamics of a Turbine

2006 ◽  
Author(s):  
Kevin Reid ◽  
John Denton ◽  
Graham Pullan ◽  
Eric Curtis ◽  
John Longley
Keyword(s):  
Steady State ◽  
Entropy Generation ◽  
Flow Rate ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Flow Conditions ◽  
Turbine Efficiency ◽  
Turbine Performance ◽  
Mainstream Flow ◽  
Flow Interactions

An investigation into the effect of stator-rotor hub gap sealing flow on turbine performance is presented. Efficiency measurements and rotor exit area traverse data from a low speed research turbine are reported. Tests carried out over a range of sealing flow conditions show that the turbine efficiency decreases with increasing sealant flow rate but that this penalty is reduced by swirling the sealant flow. Results from time-accurate and steady-state simulations using a three-dimensional multi-block RANS solver are presented with particular emphasis paid to the mechanisms of loss production. The contributions toward entropy generation of the mixing of the sealant fluid with the mainstream flow and of the perturbed rotor secondary flows are assessed. The importance of unsteady stator wake/sealant flow interactions is also highlighted.

Sign in / Sign up

Export Citation Format

Share Document