Modeling of Heat Transfer in the Surface Mounting of Electronic Components

1993 ◽  
Vol 115 (4) ◽  
pp. 373-381 ◽  
Author(s):  
S. K. Rastogi ◽  
D. Poulikakos
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Thermal Stresses ◽  
Circuit Board ◽  
Transfer Model ◽  
Thermal Gradients ◽  
Electronic Components ◽  
Board Material ◽  
Surface Mounting

In this paper a heat transfer model is presented for the determination of the temperature field of a circuit board with electronic components placed upon it and undergoing the process of surface mounting. The model is solved for a simple board configuration and the effect of the major parameters of the problem on the temperature field of the board and the components is obtained. Regions of sharp thermal gradients (causing thermal stresses and possible cracking) are identified. These regions are usually located around the edges of the electronic components as well as underneath the edges of these components within the board material.

Heat transfer model for calculation of the temperature field inside thin-walled sections in fire

2021 ◽  
Vol 169 ◽  
pp. 108416
Author(s):  
Michał Malendowski ◽  
Wojciech Szymkuć ◽  
Piotr Turkowski ◽  
Adam Glema ◽  
Wojciech Węgrzyński
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Thin Walled ◽  
In Fire

Heat Transfer Model and Analysis of Oil-Immersed Electrical Transformers with Heat Pipe Radiator

2012 ◽  
Vol 516-517 ◽  
pp. 312-315
Author(s):  
Guang Hua Li ◽  
Hong Lei Liu ◽  
De Jian Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Temperature Field ◽  
Heat Pipe ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Cooling Device ◽  
Transformer Design ◽  
Electrical Transformers ◽  
Good Agreement

This paper has formulated a heat transfer model for analyzing the cooling properties of a heat pipe cooling device of oil-immersed electrical transformer. Based on the model, the oil temperature field of a 30 KVA oil-immersed transformer has been numerical simulated, and experiments also had been conducted. Results showed that the numerical simulation has good agreement with experiment results. Results also showed that heat pipe radiator is feasible for oil-immersed electrical transformer cooling. The model can be used to analyze the oil temperature distribution properties in an oil-immersed electrical transformer with heat pipe cooling device, and provide theoretical guide for transformer design and improvement.

scholarly journals Online Determining Heat Transfer Coefficient for Monitoring Transient Thermal Stresses

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 704
Author(s):  
Magdalena Jaremkiewicz ◽  
Jan Taler
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Thermal Stresses ◽  
Thermal Power ◽  
Computer Calculation ◽  
Transient Temperature ◽  
Unsteady Temperature ◽  
The Heat Transfer Coefficient

This paper proposes an effective method for determining thermal stresses in structural elements with a three-dimensional transient temperature field. This is the situation in the case of pressure elements of complex shapes. When the thermal stresses are determined by the finite element method (FEM), the temperature of the fluid and the heat transfer coefficient on the internal surface must be known. Both values are very difficult to determine under industrial conditions. In this paper, an inverse space marching method was proposed for the determination of the heat transfer coefficient on the active surface of the thick-walled plate. The temperature and heat flux on the exposed surface were obtained by measuring the unsteady temperature in a small region on the insulated external surface of a pressure component that is easily accessible. Three different procedures for the determination of the heat transfer coefficient on the water-spray surface were presented, with the division of the plate into three or four finite volumes in the normal direction to the plate surface. Calculation and experimental tests were carried out in order to validate the method. The results of the measurements and calculations agreed very well. The computer calculation time is short, so the technique can be used for online stress determination. The proposed method can be applied to monitor thermal stresses in the components of the power unit in thermal power plants, both conventional and nuclear.

scholarly journals Calculation of temperature field of coiled wire using EFM

2018 ◽  
Vol 72 ◽  
pp. 03002
Author(s):  
Zhongjun Shu ◽  
Wei Shen ◽  
Qiang Li ◽  
Minghao Fan ◽  
Jiaqing Zhang
Keyword(s):  
Heat Transfer ◽  
Risk Assessment ◽  
Temperature Field ◽  
Fire Risk ◽  
Simulation Method ◽  
Heat Transfer Model ◽  
Numerical Results ◽  
Transfer Model ◽  
Fire Risk Assessment ◽  
Wire Method

Provided a heat transfer model of coiled wire method. Based on the method, a software of EFM (ANSYS) was used to calculate the temperature field of coiled wire. Comparisons between the experimental of RVS coiled wire and numerical results indicated the effectiveness of the method utilized. The simulation method based on EFM proved to be useful for the fire risk assessment of coiled wire.

Determination of time of death in forensic science via a 3-D whole body heat transfer model

2016 ◽  
Vol 62 ◽  
pp. 109-115 ◽  
Author(s):  
Catherine Bartgis ◽  
Alexander M. LeBrun ◽  
Ronghui Ma ◽  
Liang Zhu
Keyword(s):  
Heat Transfer ◽  
Forensic Science ◽  
Heat Transfer Model ◽  
Whole Body ◽  
Transfer Model ◽  
Time Of Death ◽  
Body Heat

Heat blockage of air gap for inner overheating of high-voltage power cable and delay of early detection

2020 ◽  
Vol 38 (4) ◽  
pp. 363-376
Author(s):  
Qiyuan Xie ◽  
Hong Chen ◽  
Yanhua Yuan
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Early Detection ◽  
High Voltage ◽  
Power Supply ◽  
Air Gap ◽  
Transfer Model ◽  
Power Cable ◽  
Response Sensitivity ◽  
Radial Heat

Early detection for inner overheating of high-voltage cable is important for safe power supply. A new radial heat transfer model is developed for a typical 110 kV cable with an air gap layer. Numerical analyses are conducted for dynamic temperature field in cable induced by hot copper core with different thicknesses of air gap. The results show that the air gap has an important heat blockage for the outward heat transfer in cable. The air gap causes the temperature inside the overheated cable to rise faster and the temperature outside slower. The air gap not only reduces the response sensitivity of the surface temperature on inner overheating but also induces the inner layers to heat up and even break down. Finally, the non-dimensional temperatures on cable surface indicate that the detection of inner overheating cable would be delayed if the air gap is not considered in calculation models.

Numerical Simulation of Hot Rolled Coil Temperature Field in Hot Coil Box

2011 ◽  
Vol 338 ◽  
pp. 572-575
Author(s):  
Gui Jie Zhang ◽  
Kang Li ◽  
Ying Zi Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Temperature Field ◽  
Temperature Distribution ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Coil Temperature ◽  
Hot Rolled ◽  
Strip Coil ◽  
Good Agreement

The heat transfer model was developed and the heat transfer of the strip coil stay in the hot coil box was analyzed. The temperature distribution of the strip coil was investigated use the model. The measured results are in good agreement with the calculated ones, has a guiding significance to further improve the technology.

Three Dimensional Transient Heat Transfer Model for Steel Billet Heating in Reheat Furnace

2012 ◽  
Author(s):  
Satish Kumar Dubey ◽  
Neelesh Agarwal ◽  
P. Srinivasan
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Oxide Scale ◽  
Three Dimensional ◽  
Heat Transfer Model ◽  
Heat Diffusion ◽  
Transient Heat Transfer ◽  
Transfer Model ◽  
Scale Thickness ◽  
Reheating Process

In steel rolling mills reheat furnaces are used to heat the billets prior to rolling processes. Reheating is one of the most energy intensive processes in the steel industries. Inadequate temperature measuring techniques and extremely complex analytical solution for temperature filed calculations demands suitable numerical model. In the present work a three dimensional transient heat transfer model is developed for billet heating in reheat furnaces. Conduction heat transfer within the billets is modeled using Finite Difference Method (FDM). Fully implicit spatial discretization approximation was used for three dimensional heat diffusion equation of billet. The three dimensional model takes into account the temperature dependent thermo physical properties, reaction heat effect and growing oxide layer. Algorithm is implemented in MATLAB® to solve three dimensional discretization equations. Model is capable of predicting the temperature field for billet and oxide scale thickness for any residence time. The predicted results are in reasonable concurrence with available data. The main objective of this work is to predict billet temperature field and oxide scale thickness for the various residence times, which may be vital for development of energy efficient optimization strategy for reheating process.

Sign in / Sign up

Export Citation Format

Share Document