A Novel High-Temperature Ejector-Topping Power Cycle

1994 ◽  
Vol 116 (1) ◽  
pp. 1-7 ◽  
Author(s):  
B. Z. Freedman ◽  
N. Lior
Keyword(s):  
High Temperature ◽  
Heat Source ◽  
Gas Turbines ◽  
Saturation Pressure ◽  
Temperature Cycle ◽  
Power Cycle ◽  
Primary Fluid ◽  
Temperature Heat ◽  
Lower Temperature ◽  
Secondary Fluid

A novel, patented topping power cycle is described that takes its energy from a very high-temperature heat source and in which the temperature of the heat sink is still high enough to operate another, conventional power cycle. The top temperature heat source is used to evaporate a low saturation pressure liquid, which serves as the driving fluid for compressing the secondary fluid in an ejector. Due to the inherently simple construction of ejectors, they are well suited for operation at temperatures higher than those that can be used with gas turbines. The gases exiting from the ejector transfer heat to the lower temperature cycle, and are separated by condensing the primary fluid. The secondary gas is then used to drive a turbine. For a system using sodium as the primary fluid and helium as the secondary fluid, and using a bottoming Rankine steam cycle, the overall thermal efficiency can be at least 11 percent better than that of conventional steam Rankine cycles.

scholarly journals Thermodynamic modelling and efficiency analysis of a class of real indirectly fired gas turbine cycles

2009 ◽  
Vol 13 (4) ◽  
pp. 41-48
Author(s):  
Zheshu Ma ◽  
Zhenhuan Zhu
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Operational Parameters ◽  
Forecast Performance ◽  
Micro Gas Turbine ◽  
Temperature Heat

Indirectly or externally-fired gas-turbines (IFGT or EFGT) are novel technology under development for small and medium scale combined power and heat supplies in combination with micro gas turbine technologies mainly for the utilization of the waste heat from the turbine in a recuperative process and the possibility of burning biomass or 'dirty' fuel by employing a high temperature heat exchanger to avoid the combustion gases passing through the turbine. In this paper, by assuming that all fluid friction losses in the compressor and turbine are quantified by a corresponding isentropic efficiency and all global irreversibilities in the high temperature heat exchanger are taken into account by an effective efficiency, a one dimensional model including power output and cycle efficiency formulation is derived for a class of real IFGT cycles. To illustrate and analyze the effect of operational parameters on IFGT efficiency, detailed numerical analysis and figures are produced. The results summarized by figures show that IFGT cycles are most efficient under low compression ratio ranges (3.0-6.0) and fit for low power output circumstances integrating with micro gas turbine technology. The model derived can be used to analyze and forecast performance of real IFGT configurations.

Fluidized-Bed Heat Transfer Modeling for the Development of Particle/Supercritical-CO2 Heat Exchanger

2017 ◽  
Author(s):  
Zhiwen Ma ◽  
Janna Martinek
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Heat Exchanger ◽  
Fluidized Bed ◽  
Solid Particles ◽  
Heat Transfer Modeling ◽  
Power Cycle ◽  
Heat Exchanger Design ◽  
Temperature Heat ◽  
The Cost

Concentrating solar power (CSP) technology is moving toward high-temperature and high-performance design. One technology approach is to explore high-temperature heat-transfer fluids and storage, integrated with a high-efficiency power cycle such as the supercritical carbon dioxide (s-CO2) Brayton power cycle. The s-CO2 Brayton power system has great potential to enable the future CSP system to achieve high solar-to-electricity conversion efficiency and to reduce the cost of power generation. Solid particles have been proposed as a possible high-temperature heat-transfer medium that is inexpensive and stable at high temperatures above 1,000°C. The particle/heat exchanger provides a connection between the particles and s-CO2 fluid in the emerging s-CO2 power cycles in order to meet CSP power-cycle performance targets of 50% thermal-to-electric efficiency, and dry cooling at an ambient temperature of 40°C. The development goals for a particle/s-CO2 heat exchanger are to heat s-CO2 to ≥720°C and to use direct thermal storage with low-cost, stable solid particles. This paper presents heat-transfer modeling to inform the particle/s-CO2 heat-exchanger design and assess design tradeoffs. The heat-transfer process was modeled based on a particle/s-CO2 counterflow configuration. Empirical heat-transfer correlations for the fluidized bed and s-CO2 were used in calculating the heat-transfer area and optimizing the tube layout. A 2-D computational fluid-dynamics simulation was applied for particle distribution and fluidization characterization. The operating conditions were studied from the heat-transfer analysis, and cost was estimated from the sizing of the heat exchanger. The paper shows the path in achieving the cost and performance objectives for a heat-exchanger design.

scholarly journals Externally Fired Combined Cycles (EFCC): Part B — Alternative Configurations and Cost Projections

1996 ◽  
Author(s):  
Stefano Consonni ◽  
Ennio Macchi
Keyword(s):  
High Temperature ◽  
Heat Exchangers ◽  
Gas Turbines ◽  
High Efficiency ◽  
Complete Combustion ◽  
Economic Issues ◽  
Temperature Heat ◽  
Combined Cycles ◽  
Power Outputs ◽  
The Cost

Externally Fired Combined Cycles (EFCC) constitute one of the options allowing the use of “dirty” fuels like coal, biomass or waste in conjunction with modern, high efficiency gas turbines. This two-part paper discusses thermodynamic, technological and economic issues crucial to the successful realization of EFCCs. Part B discusses the cycle arrangement, its implications for the design and the cost of the high temperature heat exchangers, the effects of scale and the economic prospects. An “enhanced” configuration whereby the excess air sent to the combustor is limited to the minimum required for complete combustion can reach net LHV efficiencies above 50%, with relatively low high-temperature heat transfer surface requirements. Cost projections are hindered by the uncertainty on the cost of the high temperature heat exchangers. Estimates based on published and proprietary data collected by the authors indicate that EFCCs should be cost-competitive with IGCCs, especially at medium-low power outputs.

scholarly journals High temperature heat source generation with quasi-continuous wave semiconductor lasers at power levels of 6 W for medical use

2014 ◽  
Vol 19 (10) ◽  
pp. 101502
Author(s):  
Takahiro Fujimoto ◽  
Yusuke Imai ◽  
Kazuyoku Tei ◽  
Shinobu Ito ◽  
Hideko Kanazawa ◽  
...  
Keyword(s):  
High Temperature ◽  
Heat Source ◽  
Semiconductor Lasers ◽  
Continuous Wave ◽  
Temperature Heat

scholarly journals Gas Turbine Power Plant Possibilities With a Nuclear Heat Source: Closed and Open Cycles

1990 ◽  
Author(s):  
Colin F. McDonald
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Heat Source ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Closed Cycle ◽  
Cycle System ◽  
Nuclear Heat ◽  
High Temperature Gas

With the capability of burning a variety of fossil fuels, giving high thermal efficiency, and operating with low emissions, the gas turbine is becoming a major prime-mover for a wide spectrum of applications. Almost three decades ago two experimental projects were undertaken in which gas turbines were actually operated with heat from nuclear reactors. In retrospect, these systems were ahead of their time in terms of technology readiness, and prospects of the practical coupling of a gas turbine with a nuclear heat source towards the realization of a high efficiency, pollutant free, dry-cooled power plant has remained a long-term goal, which has been periodically studied in the last twenty years. Technology advancements in both high temperature gas-cooled reactors, and gas turbines now make the concept of a nuclear gas turbine plant realizable. Two possible plant concepts are highlighted in this paper, (1) a direct cycle system involving the integration of a closed-cycle helium gas turbine with a modular high temperature gas cooled reactor (MHTGR), and (2) the utilization of a conventional and proven combined cycle gas turbine, again with the MHTGR, but now involving the use of secondary (helium) and tertiary (air) loops. The open cycle system is more equipment intensive and places demanding requirements on the very high temperature heat exchangers, but has the merit of being able to utilize a conventional combined cycle turbo-generator set. In this paper both power plant concepts are put into perspective in terms of categorizing the most suitable applications, highlighting their major features and characteristics, and identifying the technology requirements. The author would like to dedicate this paper to the late Professor Karl Bammert who actively supported deployment of the closed-cycle gas turbine for several decades with a variety of heat sources including fossil, solar, and nuclear systems.

Sign in / Sign up

Export Citation Format

Share Document