Heat Release Analysis of Oxygen-Enriched Diesel Combustion

1993 ◽  
Vol 115 (4) ◽  
pp. 761-768 ◽  
Author(s):  
D. Assanis ◽  
E. Karvounis ◽  
R. Sekar ◽  
W. Marr
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Oxygen Enrichment ◽  
Operating Conditions ◽  
Diesel Combustion ◽  
The Novel ◽  
Pressure Data ◽  
Engine Operation ◽  
Combustion Simulation ◽  
Release Analysis

A heat release correlation for oxygen-enriched diesel combustion is being developed through heat release analysis of cylinder pressure data from a single-cylinder diesel engine operating under various levels of oxygen enrichment. Results show that standard combustion correlations available in the literature do not accurately describe oxygen-enriched diesel combustion. A novel functional form is therefore proposed, which is shown to reproduce measured heat release profiles closely, under different operating conditions and levels of oxygen enrichment. The mathematical complexity of the associated curve-fitting problem is maintained at the same level of difficulty as for standard correlations. When the novel correlation is incorporated into a computer simulation of diesel engine operation with oxygen enrichment, the latter predicts pressure traces in excellent agreement with measured pressure data. This demonstrates the potential of the proposed combustion simulation to guide the application of oxygen-enriched technology successfully to a variety of multicylinder diesel systems.

A Study on the Calculation of Heat Release Rate to Compensate the Error Due to Single Zone Assumption in Diesel Engine

2005 ◽  
Author(s):  
Seung Hyup Ryu ◽  
Ki Doo Kim ◽  
Wook Hyeon Yoon ◽  
Ji Soo Ha
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Computational Analysis ◽  
Combustion Process ◽  
Operating Conditions ◽  
Zone Model ◽  
Specific Heats ◽  
Start Of Injection ◽  
Release Analysis ◽  
Improved Model

Accurate heat release analysis based on the cylinder pressure trace is important for evaluating combustion process of diesel engines. However, traditional single-zone heat release models (SZM) have significant limitations due mainly to their simplified assumptions of uniform charge and homogeneity while neglecting local temperature distribution inside cylinder during combustion process. In this study, a heat release analysis based on single-zone model has been evaluated by comparison with computational analysis result using Fire-code, which is based on multi-dimensional model (MDM). The limitations of the single-zone assumption have been estimated. To overcome these limitations, an improved model that includes the effects of spatial non-uniformity has been applied. From this improved single-zone heat release model (Improved-SZM), two effective values of specific heats ratios, denoted by γV and γH in this study, have been introduced. These values are formulated as the function of charge temperature changing rate and overall equivalence ratio by matching the results of the single-zone analysis to those of computational analysis using Fire-code about medium speed marine diesel engine. Also, it is applied that each equation of γV and γH has respectively different slopes according to several meaningful regions such as the start of injection, the end of injection, the maximum cylinder temperature, and the exhaust valve open. This calculation method based on improved single-zone model gives a good agreement with Fire-code results over the whole range of operating conditions.

Combustion Improvement System in Boilers and Incinerators

2003 ◽  
Author(s):  
Wlodzimierz Blasiak ◽  
Weihong Yang
Keyword(s):  
Temperature Distribution ◽  
Heat Release ◽  
Combustion Chamber ◽  
Flue Gas ◽  
Operating Conditions ◽  
Waste Incinerator ◽  
The Novel ◽  
Biomass Waste ◽  
Injection Angle ◽  
Waste Incinerators

This work presents the main features, advantages and evaluation of applications of the novel “Ecotube” combustion improvement and emission reduction system by Ecomb AB of Sweden and Synterprise, LLC of Chattanooga, Tennessee. In the Ecotube system, the nozzles used for mixing are put on the suitable position inside the combustion chamber to control uniformity of temperature, mixing and reactants distribution in boilers and incinerators since the formation and reduction of pollutants (NO, CO and VOC) and in-furnace reduction processes (Air/Fuel staging, SNCR, flue gas recirculation and SOx reduction by dry sorbent injection) are related directly to mixing in a combustion chamber. The novel Ecotube combustion improvement system allows better control of mixing of the gases for example from a primary combustion zone with secondary combustion air or a recirculated flue gas. By means of the novel system it is possible to better control the residence time and to some degree gas phase temperature distribution as well as the heat release distribution in the furnace of the waste incinerators or boilers. This new combustion improvement system can be applied to supply different gas or liquid media — for example air, fuel, urea or even solid powder. Using the system a more efficient and environmentally clean combustion or incineration process can be performed. The Ecotube System may be used to meet increasingly stringent environmental emissions regulations, such as NOx SIP Call, while it delivers added benefits of reduced and stabilized CO and reduced fly ash and improved boiler efficiency. The study tool used in this work to present influence of the Ecotube system design on temperature as well as uniformity of reactants and flow field is numerical modeling. Using this tool, the influence of the position of the Ecotube system and the injection angle of the nozzles are studied. The studied boilers included the biomass waste incinerator, municipal solid waste incinerator and coal fired boiler. The concept of the Heat Release Distribution Ratio is proposed to classify the heat release inside the upper furnace of the boilers or incinerators. The results show that Ecotube spreads reaction zone over a larger furnace volume. The furnace flame occupation coefficient can be as high as 45% with the Ecotube system and it is around 40% higher comparing with the conventional multinozzle mixing system. Ecotube system allows keeping far more uniform heat release distribution, more uniform temperature distribution, and thus longer life of the heat transfer surfaces inside the furnace. Position of the Ecotube system and the injection angle of the nozzles are of primary importance and can be used as a technical parameter to control the boiler operation at different loads and varying operating conditions.

scholarly journals Mechanism of Emission Reduction in HSDI Diesel Engine: Split Injection

2015 ◽  
Vol 09 (2) ◽  
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Temporal Distribution ◽  
Reaction Rates ◽  
Chemical Mechanism ◽  
Symmetric Model ◽  
Diesel Combustion ◽  
Split Injection ◽  
Engine Combustion ◽  
Experimental Values

In order to meet the stringent emission standards significant efforts have been imparted to the research and development of cleaner IC engines. Diesel combustion and the formation of pollutants are directly influenced by spatial and temporal distribution of the fuel injected. The development and validation of computational fluid dynamics (CFD) models for diesel engine combustion and emissions is described. The complexity of diesel combustion requires simulation with many complex interacting sub models in order to have a success in improving the performance and to reduce the emissions. In the present work an attempt has been made to develop a multidimensional axe-symmetric model for CI engine combustion and emissions. Later simulations have been carried out using split injection for single, double and three pulses (split injection) for which commercial validation tool FLUENT was used for simulation. The tool solves basic governing equations of fluid flow that is continuity, momentum, species transport and energy equation. Using finite volume method turbulence was modeled by using RNG K-ɛ model. Injection was modeled using La Grangian approach and reaction was modeled using non premixed combustion which considers the effects of turbulence and detailed chemical mechanism into account to model the reaction rates. The specific heats were approximated using piecewise polynomials. Subsequently the simulated results have been validated with the existing experimental values. The peak pressure obtained by simulation for single and double is 10% higher than to that of experimental value. Whereas for triple injections 5% higher than to that of experimental value. For quadruple injection the pressure has been decreased by 10% when compared to triple injection.NOX have been decreased in simulation for single, double and triple injections by 15%, 28% and 20%.For quadruple injection NOX were reduced in quadruple injection by 20% to that of triple injection. The simulated value of soot for single, double and triple injections are 12%, 22% and 12% lesser than the experimental values. For quadruple injection the soot levels were almost negligible. The simulated heat release rates for single, double and triple were reduced by 12%, 18% and 11%. For quadruple injection heat release is reduced same as to that of triple injection.

Combustion heat release analysis of ethanol or n-butanol diesel fuel blends in heavy-duty DI diesel engine

Fuel ◽  
2011 ◽  
Vol 90 (5) ◽  
pp. 1855-1867 ◽  
Author(s):  
D.C. Rakopoulos ◽  
C.D. Rakopoulos ◽  
R.G. Papagiannakis ◽  
D.C. Kyritsis
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Diesel Fuel ◽  
Heavy Duty ◽  
Combustion Heat ◽  
Fuel Blends ◽  
Release Analysis ◽  
Di Diesel Engine

A Study of the Transition Between Lean Conventional Diesel Combustion and Lean, Premixed, Low-Temperature Diesel Combustion

2007 ◽  
Author(s):  
Stephen Busch ◽  
Stanislav V. Bohac ◽  
Dennis N. Assanis
Keyword(s):  
Diesel Engine ◽  
Low Temperature ◽  
Flow Model ◽  
Transient Behavior ◽  
Diesel Combustion ◽  
Combustion Modes ◽  
Lean Premixed ◽  
Release Analysis ◽  
Separation Behavior ◽  
No Emissions

New diesel combustion modes face difficult challenges with respect to engine-out emissions and transient behavior. Transitions between lean conventional diesel combustion and lean, premixed, low-temperature diesel combustion are investigated with an automotive diesel engine. Effects of fuel pressure on transitional cycles are investigated. Cycle-by-cycle heat release analysis is performed and an exhaust mass flow model is used to obtain cycle-averaged NO concentrations. The behavior of combustion progression and NO emissions during the transitions are discussed. Observed cool-flame separation behavior is identified and explained.

Assessment of Residual Mass Estimation Methods for Cylinder Pressure Heat Release Analysis of HCCI Engines With Negative Valve Overlap

2011 ◽  
Author(s):  
Elliott A. Ortiz-Soto ◽  
Jiri Vavra ◽  
Aristotelis Babajimopoulos
Keyword(s):  
Heat Release ◽  
State Equation ◽  
Operating Conditions ◽  
Exhaust Valve ◽  
Estimation Methods ◽  
Cylinder Pressure ◽  
Hcci Engines ◽  
Release Analysis ◽  
Negative Valve Overlap ◽  
Valve Overlap

Increased residual levels in Homogeneous Charge Compression Ignition (HCCI) engines employing valve strategies such as recompression or negative valve overlap (NVO) imply that accurate estimation of residual gas fraction (RGF) is critical for cylinder pressure heat release analysis. The objective of the present work was to evaluate three residual estimation methods and assess their suitability under naturally aspirated and boosted HCCI operating conditions: i) the Simple State Equation method employs the Ideal Gas Law at exhaust valve closing (EVC); ii) the Mirsky method assumes isentropic exhaust process; and iii) the Fitzgerald method models in-cylinder temperature from exhaust valve opening (EVO) to EVC by accounting for heat loss during the exhaust process and uses measured exhaust temperature for calibration. Simulations with a calibrated and validated “virtual engine” were performed for representative HCCI operating conditions of engine speed, fuel-air equivalence ratio, NVO and intake pressure (boosting). The State Equation method always overestimated RGF by more than 10%. The Mirsky method was most robust, with average errors between 3–5%. The Fitzgerald method performed consistently better, ranging from no error to 5%, where increased boosting caused the largest discrepancies. A sensitivity study was also performed and determined that the Mirsky method was most robust to possible pressure and temperature measurement errors.

scholarly journals Oxygen-Enriched Diesel Engine Performance: A Comparison of Analytical and Experimental Results

1991 ◽  
Vol 113 (3) ◽  
pp. 365-369 ◽  
Author(s):  
R. R. Sekar ◽  
W. W. Marr ◽  
D. N. Assanis ◽  
R. L. Cole ◽  
T. J. Marciniak ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Experimental Studies ◽  
Engine Performance ◽  
Oxygen Enrichment ◽  
Published Data ◽  
Particulate Emissions ◽  
Lower Grade ◽  
Nox Emissions ◽  
Release Rates

Use of oxygen-enriched combustion air in diesel engines can lead to significant improvements in power density, as well as reductions in particulate emissions, but at the expense of higher NOx emissions. Oxygen enrichment would also lead to lower ignition delays and the opportunity to burn lower grade fuels. Analytical and experimental studies are being conducted in parallel to establish the optimal combination of oxygen level and diesel fuel properties. In this paper, cylinder pressure data acquired on a single-cylinder engine are used to generate heat release rates for operation under various oxygen contents. These derived heat release rates are in turn used to improve the combustion correlation—and thus the prediction capability—of the simulation code. It is shown that simulated and measured cylinder pressures and other performance parameters are in good agreement. The improved simulation can provide sufficiently accurate predictions of trends and magnitudes to be useful in parametric studies assessing the effects of oxygen enrichment and water injection on diesel engine performance. Measured ignition delays, NOx emissions, and particulate emissions are also compared with previously published data. The measured ignition delays are slightly lower than previously reported. Particulate emissions measured in this series of tests are significantly lower than previously reported.

Startup and Steady-State Performance of a New Renewable Hydroprocessed Depolymerized Cellulosic Diesel Fuel in Multiple Diesel Engines

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Eric Bermudez ◽  
Andrew McDaniel ◽  
Terrence Dickerson ◽  
Dianne Luning Prak ◽  
Len Hamilton ◽  
...  
Keyword(s):  
Steady State ◽  
Diesel Engine ◽  
Cetane Number ◽  
Operating Conditions ◽  
Engine Operation ◽  
Start Of Injection ◽  
Ignition Quality ◽  
Engine Testing ◽  
Engine Start ◽  
Distillate Fuel

A new hydroprocessed depolymerized cellulosic diesel (HDCD) fuel has been developed using a process which takes biomass feedstock (principally cellulosic wood) to produce a synthetic fuel that has nominally ½ cycloparaffins and ½ aromatic hydrocarbons in content. This HDCD fuel with a low cetane value (derived cetane number from the ignition quality tester, DCN = 27) was blended with naval distillate fuel (NATO symbol F-76) in various quantities and tested in order to determine how much HDCD could be blended before diesel engine operation becomes problematic. Blends of 20% HDCD (DCN = 45), 30%, 40% (DCN = 41), and 60% HDCD (DCN = 37) by volume were tested with conventional naval distillate fuel (DCN = 49). Engine start performance was evaluated with a conventional mechanically direct injected (DI) Yanmar engine and a Waukesha mechanical indirect injected (IDI) Cooperative Fuels Research (CFR) diesel engine and showed that engine start times increased steadily with increasing HDCD content. Longer start times with increasing HDCD content were the result of some engine cycles with poor combustion leading to a slower rate of engine acceleration toward rated speed. A repeating sequence of alternating cycles which combust followed by a noncombustion cycle was common during engine run-up. Additionally, steady-state engine testing was also performed using both engines. HDCD has a significantly higher bulk modulus than F76 due to its very high aromatic content, and the engines showed earlier start of injection (SOI) timing with increasing HDCD content for equivalent operating conditions. Additionally, due to the lower DCN, the higher HDCD blends showed moderately longer ignition delay (IGD) with moderately shorter overall burn durations. Thus, the midcombustion metric (CA50: 50% burn duration crank angle position) was only modestly affected with increasing HDCD content. Increasing HDCD content beyond 40% leads to significantly longer start times.

Sign in / Sign up

Export Citation Format

Share Document