An Explanation for Observed Compression Ratios in Internal Combustion Engines

1991 ◽  
Vol 113 (4) ◽  
pp. 511-513 ◽  
Author(s):  
S. A. Klein
Keyword(s):  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Otto Cycle ◽  
Diesel Cycle ◽  
Maximum Work ◽  
The Ideal

Comparisons of the compression ratios, efficiencies, and work of the ideal Otto and Diesel cycles are presented at conditions that yield maximum work per cycle. The compression ratios that maximize the work of the Diesel cycle are found always to be higher than those for the Otto cycle at the same operating conditions, although the thermal efficiencies are nearly identical. The compression ratios that maximize the work of the Otto and Diesel cycles compare well with the compression ratios employed in corresponding production engines.

scholarly journals The influence of centrial forces on crankshaft bearing lubrication is in emergency modes of the engine of the car

2021 ◽  
Vol 12 (2) ◽  
pp. 112-121
Author(s):  
Oleksandr Khrulev ◽  
◽  
Olexii Saraiev ◽  
Iryna Saraieva ◽  
◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Operating Mode ◽  
Internal Combustion ◽  
Technical Condition ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Connecting Rod ◽  
Oil Supply ◽  
Technical Expert ◽  
The Difference

The analysis of the crankshaft bearing condition of the automotive internal combustion engines in the case of insufficiency and breakage of oil supply to them is carried out. It is noted that this fault is one of the most common causes of damage to rubbing pairs in operation. At the same time, the different groups of bearings are often damaged, which cannot be explained within the framework of existing models of plain bearing lubrication. The objective of the work is to develop a mathematical model of oil supply to connecting rod bearings in emergency mode, taking into account the characteristic features of the bearing design. The model also, depending on the nature of the damage, should help to determine and explain the causes of bearing failures if they occur in different modes when operating conditions are broken. A computational model has been developed that makes it possible to assess the effect of design differences in the features of oil supply and the action of the centrifugal forces during crankshaft rotation on the oil column in the lubrication hole where oil is supplied to the conrod bearing. Calculations of the change in time of the oil supply pressure to the connecting rod bearings for the various designs of the crankshaft lubrication holes have been performed. It is shown that, depending on the operating mode of the engine and its design, the oil pressure in front of the connecting rod bearings does not disappear immediately after oil supply failure to crankshaft. Moreover, the lower the crankshaft speed is, the longer the lubrication of the conrod bearings will continue. The calculation results are confirmed by the data of the expert studies of the engine technical condition, in which the crankshaft was wedged in the damaged main bearings was found in the absence of serious damage to the connecting rod ones. It has been found that such features of the damage correspond to an rapid breakage of the oil supply to the crankshaft in the case of such operational damage as the oil pump and pressure reducing valve failure, the oil filter seal and oil pan destruction, etc. The developed model explains the difference in lubrication conditions and in the damage feature to the main and connecting rod bearings in the emergency cases of the oil supply breakage, which are observed during operation, and helps to clarify the failure causes. This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines when the operating conditions are broken.

scholarly journals The use of thermography in the diagnosis of ship piston internal combustion engines

2018 ◽  
Vol 182 ◽  
pp. 01027
Author(s):  
Jan Monieta
Keyword(s):  
Infrared Thermography ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Internal Combustion ◽  
Technical Condition ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Destructive Testing ◽  
Fault State ◽  
Floating Objects

The intensity of infrared radiation emitted by objects depends mainly on their temperature. One of the diagnostic signals may be the temperature field. In infrared thermography, this quantity is used as an indicator of the technical condition of marine objects. The article presents an overview of the use of infrared thermography for the diagnosis mainly of marine piston floating objects and various types of reciprocating internal combustion engines as well as examples of own research results. A general introduction to infrared thermography and common procedures for temperature measurement and non-destructive testing are presented. Experimental research was carried out both in laboratory conditions and in the operating conditions of sea-going vessels. Experimental studies consisted of the presentation of photographs of the same objects made in visible light and the use of infrared thermography. The same objects were also compared, but for different cylinders of the tested internal combustion engines as well as for the up state and fault state. The characteristics of the temperature values at selected points were taken depending on the engine load along with the approximation mathematical models of these dependencies.

scholarly journals A zonal approach for estimating pressure ratio at compressor extreme off-design conditions

2018 ◽  
Vol 20 (4) ◽  
pp. 393-404 ◽  
Author(s):  
José Galindo ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Daniel Tarí ◽  
Hadi Tartoussi ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Pressure Ratio ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
One Dimensional ◽  
Performance Map

Zero-dimensional/one-dimensional computational fluid dynamics codes are used to simulate the performance of complete internal combustion engines. In such codes, the operation of a turbocharger compressor is usually addressed employing its performance map. However, simulation of engine transients may drive the compressor to work at operating conditions outside the region provided by the manufacturer map. Therefore, a method is required to extrapolate the performance map to extended off-design conditions. This work examines several extrapolating methods at the different off-design regions, namely, low-pressure ratio zone, low-speed zone and high-speed zone. The accuracy of the methods is assessed with the aid of compressor extreme off-design measurements. In this way, the best method is selected for each region and the manufacturer map is used in design conditions, resulting in a zonal extrapolating approach aiming to preserve accuracy. The transitions between extrapolated zones are corrected, avoiding discontinuities and instabilities.

A Novel Electromechanical Solution for Cam-Switching in High Performance Internal Combustion Engines

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Andrea De Martin ◽  
Giovanni Jacazio ◽  
Massimo Sorli
Keyword(s):  
High Performance ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Valve Lift ◽  
Combustion Engines ◽  
Critical Aspect ◽  
Conceptual Design Phase ◽  
Common Strategy ◽  
Switch System

Abstract The variation of the valve lift is a fairly common strategy currently adopted in several in-service internal combustion engines to optimize their performance depending on the operating conditions of the vehicle. The most critical aspect to consider during the conceptual design phase of a cam switch system is the extremely narrow window of opportunity to perform the cam change, which duration is defined by the time during which the corresponding valve lift is null. To meet this requirement and ensure safe, repeatable movements, a novel architecture based on the combination of a new electromechanical actuator and its dedicated control system is presented. The architecture is at first introduced with reference to the numerous examples available in the literature, and hence mathematically described. The dynamic model of the system derived from the presented equation is then used to study the performance of the presented solution and define its control strategy. Results are finally presented and discussed.

Performance study of the hypocycloid gear mechanism for internal combustion engine applications

2019 ◽  
pp. 146808741989358 ◽  
Author(s):  
Mostafa A ElBahloul ◽  
ELsayed S Aziz ◽  
Constantin Chassapis
Keyword(s):  
Internal Combustion Engine ◽  
Thermodynamic Model ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Otto Cycle ◽  
Engine Efficiency ◽  
Gear Mechanism ◽  
Crank Mechanism

Fuel conversion efficiency is one of the main concerns in the field of internal combustion engine systems. Although the Otto cycle delivers the maximum efficiency possible in theory, the kinematics of the slider–crank mechanism of the conventional internal combustion engines makes it difficult to reach this level of efficiency in practice. This study proposes using the unique hypocycloid gear mechanism instead of the conventional slider–crank mechanism for the internal combustion engines to increase engine efficiency and minimize frictional power losses. The hypocycloid gear mechanism engine’s kinematics provides the means for the piston-rod assembly to reciprocate in a straight-line motion along the cylinder axis besides achieving a nonlinear rate of piston movement. As a result, this characteristic allows for a true constant-volume combustion, which in turn would lead to higher work output. An in-cylinder gas volume change model of the hypocycloid gear mechanism engine was developed and incorporated into the thermodynamic model for the internal combustion engine cycle. The thermodynamic model of the hypocycloid gear mechanism engine was developed and simulated using MATLAB/Simulink software. A comparison between the conventional engine and the hypocycloid gear mechanism engine in terms of engine performance characteristics showed the enhancements achieved using hypocycloid gear mechanism for internal combustion engine applications. The hypocycloid gear mechanism engine analysis results indicated higher engine efficiency approaching that of the Otto cycle.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Physicochemical properties of ethanol with the addition of biodiesel for use in Otto cycle internal combustion engines: Results and revision

2017 ◽  
Vol 74 ◽  
pp. 1181-1188 ◽  
Author(s):  
Edson Vanzela ◽  
Willian Cézar Nadaleti ◽  
Reinaldo Aparecido Bariccatti ◽  
Paulo André Cremonez ◽  
Eduardo de Rossi ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Otto Cycle

scholarly journals Experimental Research of Fibrous Materials for Two-Stage Filtration of the Intake Air of Internal Combustion Engines

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7166
Author(s):  
Tadeusz Dziubak ◽  
Leszek Bąkała ◽  
Sebastian Dominik Dziubak ◽  
Kamil Sybilski ◽  
Michał Tomaszewski
Keyword(s):  
Pressure Drop ◽  
Absorption Coefficient ◽  
Internal Combustion Engines ◽  
Filter Material ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Two Stage ◽  
Stage System ◽  
Dust Absorption

Pollutant properties in intake air to internal combustion engines were analyzed. Mineral dust particles’ influence on accelerated engine components’ wear was discussed. Dust concentration values in the air under various operating conditions in trucks and special vehicles were presented. The idea and necessity for using two-stage filters, operating in a “multi-cyclone–porous partition” system for vehicles operated in dusty air conditions, are presented. Information from the literature information has been presented, showing that impurities in small grain sizes reduce fiber bed absorbency. It has been shown that such a phenomenon occurs during filter material operation, located directly behind the inertial filter (multi-cyclone), which off-road vehicles are equipped with. It results in a greater pressure drop intensity increase and a shorter proper filter operation period. It has been shown that filter material selection for the motor vehicle air filter requires knowledge of the mass of stopped dust per filtration unit area (dust absorption coefficient km) determined for a given permissible resistance value Δpfdop. It has been shown that there is no information on absorption coefficient values for filter materials operating in a two-stage “multi-cyclone–porous partition” separation system. Original methodology and conditions for determining dust absorption coefficient (km) of a separation partition, operating under the conditions of two-stage filtration, were presented. The following characteristics were tested: separation efficiency, filtration performance, and pressure drop characteristics of three different filtration partitions. These were A (cellulose), B (cellulose and polyester), and C (cellulose, polyester, and nanofibers layer), working individually and in a two-stage system—behind the cyclone. Granulometric dust composition dosed into the cyclone and cyclone downstream was determined. During tests, conditions corresponding to air filter’s actual operating conditions, including separation speed and dust concentration in the air, were maintained. For the pressure drop values, the dust absorption coefficient (km) values of three different filtration partitions (A, B, and C), working individually and in a two-stage system—behind the cyclone—were determined experimentally.

Sign in / Sign up

Export Citation Format

Share Document