An Enhanced End Milling Surface Texture Model Including the Effects of Radial Rake and Primary Relief Angles

1994 ◽  
Vol 116 (2) ◽  
pp. 166-174 ◽  
Author(s):  
S. N. Melkote ◽  
A. R. Thangaraj
Keyword(s):  
Surface Roughness ◽  
Surface Texture ◽  
End Milling ◽  
Three Dimensional ◽  
Roughness Parameter ◽  
Surface Profile ◽  
Dimensional Structure ◽  
Machined Surface ◽  
Texture Model ◽  
Parameter Values

An enhanced surface texture model for predicting the two- and three-dimensional structure of the surface generated by the end cutting edges on the bottom of an end mill is presented. This model includes the effects of the radial rake and the primary end tooth relief angles which have been neglected in the models available to date. Non-ideal effects such as cutter runout and back-cutting are explicitly modeled. An algorithm to simulate the two- and three-dimensional milled surface is presented. It is shown that the main effect of the radial rake and the primary end tooth relief angles is to increase the surface roughness parameter values. The effectiveness of the enhanced model in accurately capturing the major features of the machined surface texture and in closely predicting the roughness parameter values is demonstrated through experiments and model simulations. It is shown that the enhanced model predicts both the shape of the surface profile and the surface roughness parameters more accurately than the existing models in the literature.

scholarly journals Influence of Relative Displacement on Surface Roughness in Longitudinal Turning of X37CrMoV5-1 Steel

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1317
Author(s):  
Michal Skrzyniarz ◽  
Lukasz Nowakowski ◽  
Edward Miko ◽  
Krzysztof Borkowski
Keyword(s):  
Surface Roughness ◽  
Standard Deviation ◽  
Surface Texture ◽  
Roughness Parameter ◽  
Relative Displacement ◽  
Edge Radius ◽  
Shaping Process ◽  
Feed Value ◽  
Longitudinal Turning ◽  
Final Effect

The shaping process of surface texture is complicated and depends on many factors and phenomena accompanying them. This article presents the author’s test stand for the measurement of relative displacements in a tool–workpiece system during longitudinal turning. The aim of this study was to determine the influence of edge radius on the relative displacement between the tool and workpiece. The cutting process was carried out with inserts with different edge radii for X37CrMoV5-1 steel. As a result of the research, vibration charts of the tool–workpiece system were obtained. In the range of feed 0.03–0.18 mm/rev, the values of the standard deviation of relative displacements in the x-axis were obtained in the range of 0.36–0.78 μm for the insert with an edge radius of rn = 48.8 μm. As a result of the work, it was determined that for the feed value of 0.12 mm/rev for all inserts, the relative displacements are the smallest. As the final effect, the formula for forecasting the Ra roughness parameter was presented.

Surface Roughness Identification in End Milling Using Vibration Signals and Fuzzy Clustering

2016 ◽  
Author(s):  
Issam Abu-Mahfouz ◽  
Amit Banerjee ◽  
A. H. M. Esfakur Rahman
Keyword(s):  
Surface Roughness ◽  
Fuzzy Clustering ◽  
Wavelet Transforms ◽  
Fourier Transforms ◽  
End Milling ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machined Surface ◽  
Vibration Signals

The study presented involves the identification of surface roughness in Aluminum work pieces in an end milling process using fuzzy clustering of vibration signals. Vibration signals are experimentally acquired using an accelerometer for varying cutting conditions such as spindle speed, feed rate and depth of cut. Features are then extracted by processing the acquired signals in both the time and frequency domain. Techniques based on statistical parameters, Fast Fourier Transforms (FFT) and the Continuous Wavelet Transforms (CWT) are utilized for feature extraction. The surface roughness of the machined surface is also measured. In this study, fuzzy clustering is used to partition the feature sets, followed by a correlation with the experimentally obtained surface roughness measurements. The fuzzifier and the number of clusters are varied and it is found that the partitions produced by fuzzy clustering in the vibration signal feature space are related to the partitions based on cutting conditions with surface roughness as the output parameter. The results based on limited simulations are encouraging and work is underway to develop a larger framework for online cutting condition monitoring system for end milling.

Development of the cBN Electroplated End-Mill for High Precision Machining of CFRP

2020 ◽  
Author(s):  
Shinnosuke Yamashita ◽  
Tatsuya Furuki ◽  
Hiroyuki Kousaka ◽  
Toshiki Hirogaki ◽  
Eiichi Aoyama ◽  
...  
Keyword(s):  
Surface Roughness ◽  
End Milling ◽  
Drop Out ◽  
End Mill ◽  
Machined Surface ◽  
Side Milling ◽  
Reinforced Plastics ◽  
Milled Surface ◽  
Grinding Conditions ◽  
Grinding Tool

Abstract Recently, the demand of carbon fiber reinforced plastics (CFRP) has been rapidly increased in various fields. In most cases, CFRP products requires a finish machining like cutting or grinding. In the case of an end-milling, burrs and uncut fibers are easy to occur. On the other hand, a precise machined surface and edge will be able to obtain by using the grinding tool. Therefore, this research has been developed a novel the cBN electroplated end-mill that combined end-mill and grinding tool. In this report, the effectiveness of developed tool was investigated. First, the developed tool cut the CFRP with side milling. As the result, the cBN abrasives that were fixed on the outer surface of developed tool did not drop out. Next, the end-milled surface of CFRP was ground with the developed tool under several grinding conditions based on the Design of Experiment. Consequently, the optimum grinding condition that can obtain the sharp edge which does not have burrs and uncut fibers was found. However, surface roughness was not good enough. Thus, an oscillating grinding was applied. In addition, the theoretical surface roughness formula in case using the developed tool was formularized. As the result, the required surface roughness in the airplane field was obtained.

scholarly journals Influence of Chatter of VMC Arising During End Milling Operation and Cutting Conditions on Quality of Machined Surface

1970 ◽  
Vol 2 (1) ◽  
Author(s):  
A.K.M.N. Amin, M.A. Rizal, and M. Razman
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Metal Removal ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
End Mill ◽  
Machined Surface ◽  
Operating Cycle ◽  
Wide Range

Machine tool chatter is a dynamic instability of the cutting process. Chatter results in poor part surface finish, damaged cutting tool, and an irritating and unacceptable noise. Exten¬sive research has been undertaken to study the mechanisms of chatter formation. Efforts have been also made to prevent the occurrence of chatter vibration. Even though some progress have been made, fundamental studies on the mechanics of metal cutting are necessary to achieve chatter free operation of CNC machine tools to maintain their smooth operating cycle. The same is also true for Vertical Machining Centres (VMC), which operate at high cutting speeds and are capable of offering high metal removal rates. The present work deals with the effect of work materials, cutting conditions and diameter of end mill cutters on the frequency-amplitude characteristics of chatter and on machined surface roughness. Vibration data were recorded using an experimental rig consisting of KISTLER 3-component dynamometer model 9257B, amplifier, scope meters and a PC.  Three different types of vibrations were observed. The first type was a low frequency vibration, associated with the interrupted nature of end mill operation. The second type of vibration was associated with the instability of the chip formation process and the third type was due to chatter. The frequency of the last type remained practically unchanged over a wide range of cutting speed.  It was further observed that chip-tool contact processes had considerable effect on the roughness of the machined surface.Key Words: Chatter, Cutting Conditions, Stable Cutting, Surface Roughness.

Measuring and Quantifying the Surface-Roughness Anisotropy of Modeled and Industrially Produced Surfaces

2005 ◽  
Vol 6-8 ◽  
pp. 573-582 ◽  
Author(s):  
C.M. Wichern ◽  
W. Rasp
Keyword(s):  
Surface Roughness ◽  
Rolling Direction ◽  
Three Dimensional ◽  
Roughness Parameter ◽  
Orientation Angle ◽  
Textured Surface ◽  
Angular Orientation ◽  
Textured Surfaces ◽  
Average Roughness ◽  
Dimensional Surface

‘Three-dimensional surface profilometry’ when used for analysis and product specification reports roughness parameters that provide an average surface description over a relatively large area. Many commercial sheet steels are produced with special textured surfaces for tribological benefits or appearance benefits. These surfaces, as well as others, may demonstrate high levels of roughness anisotropy that is not quantifiable by simple three dimensional surface parameters. This anisotropy can play an important role in the surface appearance of the finished product and in the tribological behaviour during forming. The current work presents a method for quantifying surface-roughness features as a function of angular orientation with respect to rolling direction. The measurement methodology was applied to several model surfaces and one industrially produced electron-beam textured-surface (EBT). This methodology extracts multiple surface-height profiles of the same angular orientation from a single surface and calculates an average roughness parameter for the orientation angle based on the multiple profiles. Particularly interesting results were the large number of profiles necessary to obtain repeatable values for the roughness variation with respect to direction and the strong influence of surface feature size on the repeatability of said results. These results indicate that care must be taken when using a single extracted profile to represent a ‘three-dimensional’ surface.

An Approach to Improve Cutting Performance in Micromilling of Titanium Alloy

2020 ◽  
Vol 8 (2) ◽  
Author(s):  
Yunn-Shiuan Liao ◽  
Tsung-Hsien Li ◽  
Yi-Chen Liu
Keyword(s):  
Carbon Dioxide ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Flank Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Liquid Carbon ◽  
Dry Cutting ◽  
Machined Surface ◽  
Liquid Carbon Dioxide

Abstract Application of liquid carbon dioxide to improve cutting performance in micro-end milling of Ti-6Al-4V titanium alloy was proposed in this study. It was found that the machined roughness decreased with the cutting speed as observed in the conventional cutting, when a 0.5 mm diameter end milling cutter was used in dry cutting. But, the tiny and shattered chips produced by the use of 0.3 mm diameter cutter could adhere on the machined surface and deteriorate surface finish, if the cutting speed was higher than 40 m/min. Cutting temperature was effectively decreased by applying liquid carbon dioxide during micromilling, which in turn reduced the amount of chips adhering on the machined surface and lowered flank wear. The surface roughness Ra at a cutting speed of 70 m/min was improved from 0.09 μm under dry cutting to 0.04 μm under the liquid carbon dioxide assisted cutting condition. And there were no flank wear and very few burrs left on the machined surface for the condition used in the experiment. The height of the burrs was only 25% of that under dry cutting. More, minimum quantity lubrication (MQL) was proposed to be applied together with the liquid carbon dioxide to enhance lubrication effect. It was noted that the machined surface roughness was further decreased by 15% as compared with that when the liquid carbon dioxide was applied alone. The height of burrs was reduced from 32 μm to 16 μm.

Investigation of Surface Characteristics and Chip Morphology in High Speed Cutting of Inconel718 Based on SHPB System

2019 ◽  
Author(s):  
Zengqiang Wang ◽  
Zhanfei Zhang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Kunyang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Surface Profile ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machined Surface ◽  
High Speed Cutting

Abstract High speed cutting (HSC) technology has the characteristics of high material removal rates and high machining precision. In order to study the relationships between chip morphology and machining surface characteristic in high speed cutting of superalloy Inconel718. High-speed orthogonal cutting experiment are carried out by used a high speed cutting device based on split Hopkinson pressure bar (SHPB). The specimen surfaces and collected chips were then detected with optical microscope, scanning electron microscope and three-dimensional surface profile measuring instrument. The results show that within the experimental parameters (cutting speed from 8–16m/s, depth of cut 0.1–0.5mm), the obtained chips are sawtooth chips and periodic micro-ripple appear on the machined surface. With the cutting speed increases, machining surface roughness is decreases from 1.4 to 0.99μm, and the amplitude of periodic ripples also decreases. With the cutting depth increases, the machining surface roughness increases from 0.96 to 5.12μm and surface topography becomes worse. With the increase of cutting speed and depth of cut, the chips are transform from continues sawtooth to sawtooth fragment. By comparing the frequency of surface ripples and sawtooth chips, it is found that they are highly consistent.

Considerations Regarding Some Surface State Parameters Characterized by a more Restricted Use

2015 ◽  
Vol 809-810 ◽  
pp. 93-98
Author(s):  
Ionuţ Urzică ◽  
Ciprian Râznic ◽  
Mihai Apostol ◽  
Corina Mihaela Pavăl ◽  
Mihai Boca ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Roughness Parameter ◽  
Cutting Speed ◽  
Roughness Parameters ◽  
Turning Process ◽  
Nose Radius ◽  
Machined Surface ◽  
Surface Roughness Parameter ◽  
Surface Roughness Parameters ◽  
Restricted Use

Frequently, on the drawings of mechanical parts, only indications concerning the surface roughness parameter Ra and, relatively rarely, the surface roughness parameter Rz are included. However, the study of the machined surface roughness highlights the necessity to use yet other surface roughness parameters, in order to have a clearer image on the state of the machined surface. Some other surface roughness parameters possible to be used and presenting importance, without the parameters Ra and Rz, were highlighted. One took into consideration the possibility of measuring parameters Rsk and Rmr by means of the available surface roughness testers. Experimental researches of turning by applying the method of full factorial experiment were developed. As input factors in turning process, the cutting speed, the feed rate and the tool nose radius were used. The experimental results were mathematically processed, being determined empirical mathematical models that highlight the influence of certain input factors of turning process on the values of some surface roughness parameters characterized by a more restricted use

ANALYSIS OF THE CORRELATION BETWEEN FRACTAL STRUCTURE OF CUTTING FORCE SIGNAL AND SURFACE ROUGHNESS OF MACHINED WORKPIECE IN END MILLING OPERATION

Fractals ◽  
2019 ◽  
Vol 27 (02) ◽  
pp. 1950013 ◽  
Author(s):  
AHMAD THUFFAIL THASTHAKEER ◽  
ALI AKHAVAN FARID ◽  
CHANG TECK SENG ◽  
HAMIDREZA NAMAZI
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Forces ◽  
End Milling ◽  
Complex Structure ◽  
Machined Surface ◽  
End Mills ◽  
Machining Operations

Analysis of the machined surface is one of the major issues in machining operations. On the other hand, investigating about the variations of cutting forces in machining operation has great importance. Since variations of cutting forces affect the surface quality of machined workpiece, therefore, analysis of the correlation between cutting forces and surface roughness of machined workpiece is very important. In this paper, we employ fractal analysis in order to investigate about the complex structure of cutting forces and relate them to the surface quality of machined workpiece. The experiments have been conducted in different conditions that were selected based on cutting depths, type of cutting tool (serrated versus. square end mills) and machining conditions (wet and dry machining). The result of analysis showed that among all comparisons, we could only see the correlation between complex structure of cutting force and the surface roughness of machined workpiece in case of using serrated end mill in wet machining condition. The employed methodology in this research can be widely applied to other types of machining operations to analyze the effect of variations of different parameters on variability of cutting forces and surface roughness of machined workpiece and then investigate about their correlation.

Correlation study of tool flank wear with machined surface texture in end milling

Measurement ◽  
2013 ◽  
Vol 46 (10) ◽  
pp. 4249-4260 ◽  
Author(s):  
S. Dutta ◽  
A. Kanwat ◽  
S.K. Pal ◽  
R. Sen
Keyword(s):  
Surface Texture ◽  
Flank Wear ◽  
End Milling ◽  
Correlation Study ◽  
Machined Surface ◽  
Tool Flank Wear
Sign in / Sign up

Export Citation Format

Share Document