Modal Sensors/Actuators

1990 ◽  
Vol 57 (2) ◽  
pp. 434-441 ◽  
Author(s):  
C.-K. Lee ◽  
F. C. Moon
Keyword(s):  
Distributed Control ◽  
Piezoelectric Sensors ◽  
Structural Vibration ◽  
Flexible Plate ◽  
One Dimensional ◽  
Distributed Sensor ◽  
Mode 2 ◽  
Laminate Theory ◽  
On Line ◽  
The One

A piezoelectric laminate theory that uses the piezoelectric phenomenon to effect distributed control and sensing of structural vibration of a flexible plate has been used to develop a class of distributed sensor/actuators, that of modal sensors/actuators. The one-dimensional modal sensors/actuator equations are first derived theoretically and then examined experimentally. These modal equations indicate that distributed piezoelectric sensors/actuators can be adopted to measure/excite specific modes of one-dimensional plates and beams. If constructed correctly, actuator/observer spillover will not be present in systems adopting these types of sensors/actuators. A mode 1 and a mode 2 sensor for a one-dimensional cantilever plate were constructed and tested to examine the applicability of the modal sensors/actuators. A modal coordinate analyzer which allows us to measure any specific modal coordinate on-line real-time is proposed. Finally, a way to create a special two-dimensional modal sensor is presented.

A Hybrid Flexoelectric-Piezoelectric Design for Structural Sensing

2014 ◽  
Author(s):  
S. D. Hu ◽  
H. Li
Keyword(s):  
Cylindrical Shell ◽  
Piezoelectric Layer ◽  
Piezoelectric Sensors ◽  
Structural Vibration ◽  
Strain Component ◽  
Distributed Sensors ◽  
Layer Composite ◽  
On Line ◽  
Hybrid Configuration ◽  
Membrane Strain

Distributed sensing using piezoelectric sensors have been widely studied on shell-type structures. Usually, sensing signals by piezoelectric sensors are contributed by both membrane and bending strains which are always closely coupled so that either of them is not easy to be extracted from the physical output signal. Based on the direct flexoelectric effect, flexoelectric materials are promising transducers with capability of monitoring the structural vibration especially the bending behavior. In this study, a hybrid flexoelectric-piezoelectric configuration based on a cylindrical shell is proposed to separately monitor its membrane and bending behaviors. A five-layer composite cylindrical shell is established. A piezoelectric layer is embedded in the neutral surface of the shell and flexoelectric layers are laminated on the inner and outer surfaces. The piezoelectric layer and the flexoelectric layers are segmented into a number of patches serving as distributed sensors. Results show that for piezoelectric sensors, only the membrane strain component is detected while the flexoelectric sensing signals are only contributed by the bending strain component. In order to further obtain signal information respectively indicating the longitudinal and the circumferential bending strains, an orthogonal lamination scheme of flexoelectric layers was proposed. Signal modulate circuits with different flexoelectric material constants were also designed in order to directly achieve on-line monitoring. Spatial distributions of hybrid flexoelectric-piezoelectric sensing signals were evaluated and analyzed in case studies. Results show that by implementing the orthogonal lamination scheme, the flexoelectric sensors can individually predict the longitudinal and circumferential bending behaviors. Such a hybrid configuration is also applicable to other structures.

scholarly journals The Assessment of Cross Machine Openness Uniformity of a Fiber Feed Matt

2000 ◽  
Vol os-9 (4) ◽  
pp. 1558925000OS-90
Author(s):  
Ayad Oumera ◽  
Abdelfattah M. Seyam ◽  
William Oxenham
Keyword(s):  
Thickness Measurement ◽  
One Dimensional ◽  
Line Measurement ◽  
On Line ◽  
Compression Data ◽  
The One ◽  
Compression Characteristics ◽  
Input Level

The one-dimensional characteristic of yarn has resulted in very little attention being given to the uniformity of carded web in the cross machine direction. The development of nonwovens has prompted researchers to reconsider the importance of cross machine uniformity in determining the total uniformity of the carded web. It is therefore important to develop manual and online techniques to quantify cross machine uniformity at both the input and output of the card. At the card input, uniformity is taken as representing both mass and openness characteristics of the feed matt. While at the card output, there are many available techniques that allow the on-line measurement of the mass uniformity of the carded web, determination of uniformity at the input level is more difficult. The approach that was taken was to use an off-line technique to find the mass and openness of the feed matt at different locations across the card. While traditionally mass as a property has been given a lot of importance, much less attention has been given to the concept of openness. This is due in part to the difficulty in quantifying openness. Openness is believed to have great significance in determining the overall quality of the carded web, especially with regard to the formation of neps. In order to make the concept of openness more clear, it was found necessary to develop a way of quantifying it. This was done by performing a compression test on the feed matt, and then fitting the compression data with an exponential curve. The coefficient of the exponent was used to represent openness. This approach was used to find the effect of the feed roller (pin type) on cross machine uniformity. It was found that the squeezing of the feed roller did not have an effect in redistributing the mass of the feed matt, but did have an effect in changing the openness of the feed matt. Because of the difficulty involved in the handling of the feed matt, a newly developed technique is suggested to characterize openness. While this method still relies on the compression characteristics of the feed matt, it is more appropriate because it is performed on-line. Preliminary results are reported. It was found that thickness measurement under carefully selected pressure value could be used to characterize openness precisely.

Exploring the Multidimensional Facets of Authoritarianism: Authoritarian Aggression and Social Dominance Orientation

2008 ◽  
Vol 67 (1) ◽  
pp. 51-60 ◽  
Author(s):  
Stefano Passini
Keyword(s):  
Social Dominance ◽  
Factor Model ◽  
Three Dimensional ◽  
Social Dominance Orientation ◽  
Model Fit ◽  
Regression Analyses ◽  
One Dimensional ◽  
Confirmatory Factor ◽  
The One ◽  
Better Than

The relation between authoritarianism and social dominance orientation was analyzed, with authoritarianism measured using a three-dimensional scale. The implicit multidimensional structure (authoritarian submission, conventionalism, authoritarian aggression) of Altemeyer’s (1981, 1988) conceptualization of authoritarianism is inconsistent with its one-dimensional methodological operationalization. The dimensionality of authoritarianism was investigated using confirmatory factor analysis in a sample of 713 university students. As hypothesized, the three-factor model fit the data significantly better than the one-factor model. Regression analyses revealed that only authoritarian aggression was related to social dominance orientation. That is, only intolerance of deviance was related to high social dominance, whereas submissiveness was not.

Adiabatic large polarons in anisotropic molecular crystals

2011 ◽  
Vol 35 (1) ◽  
pp. 15-27
Author(s):  
Zoran Ivić ◽  
Željko Pržulj
Keyword(s):  
Energy Transfer ◽  
Effective Mass ◽  
Molecular Crystals ◽  
Single Chain ◽  
Proper Understanding ◽  
One Dimensional ◽  
Interchain Coupling ◽  
Large Polaron ◽  
The One

Adiabatic large polarons in anisotropic molecular crystals We study the large polaron whose motion is confined to a single chain in a system composed of the collection of parallel molecular chains embedded in threedimensional lattice. It is found that the interchain coupling has a significant impact on the large polaron characteristics. In particular, its radius is quite larger while its effective mass is considerably lighter than that estimated within the one-dimensional models. We believe that our findings should be taken into account for the proper understanding of the possible role of large polarons in the charge and energy transfer in quasi-one-dimensional substances.

Aspects of the Evolution of the Romanian Tourists’ Preferences Concerning the Domestic Tourist Destinations

2019 ◽  
Vol 10 (1) ◽  
pp. 21-28
Author(s):  
Aniela Bălăcescu ◽  
Radu Șerban Zaharia
Keyword(s):  
Logistic Model ◽  
Local Level ◽  
Medium Term ◽  
Tourist Destinations ◽  
Tourism Management ◽  
Production And Consumption ◽  
On Line ◽  
The One ◽  
Long Term Studies

Abstract Tourist services represent a category of services in which the inseparability of production and consumption, the inability to be storable, the immateriality, and last but not least non-durability, induces in tourism management a number of peculiarities and difficulties. Under these circumstances the development of medium-term strategies involves long-term studies regarding on the one hand the developments and characteristics of the demand, and on the other hand the tourist potential analysis at regional and local level. Although in the past 20 years there has been tremendous growth of on-line booking made by household users, the tour operators agencies as well as those with sales activity continue to offer the specific services for a large number of tourists, that number, in the case of domestic tourism, increased by 1.6 times in case of the tour operators and by 4.44 times in case of the agencies with sales activity. At the same time, there have been changes in the preferences of tourists regarding their holiday destinations in Romania. Started on these considerations, paper based on a logistic model, examines the evolution of the probabilities and scores corresponding to the way the Romanian tourists spend their holidays on the types of tourism agencies, actions and tourist areas in Romania.

Modelling Techniques in Applied Glaciology: Numerical Modelling of Avalanches

1983 ◽  
Vol 4 ◽  
pp. 297-297
Author(s):  
G. Brugnot
Keyword(s):  
Finite Difference Method ◽  
Transverse Velocity ◽  
Longitudinal Velocity ◽  
Momentum Conservation ◽  
Dimensional Model ◽  
One Dimensional ◽  
Modelling Techniques ◽  
Reference Grid ◽  
The One ◽  
Near Future

We consider the paper by Brugnot and Pochat (1981), which describes a one-dimensional model applied to a snow avalanche. The main advance made here is the introduction of the second dimension in the runout zone. Indeed, in the channelled course, we still use the one-dimensional model, but, when the avalanche spreads before stopping, we apply a (x, y) grid on the ground and six equations have to be solved: (1) for the avalanche body, one equation for continuity and two equations for momentum conservation, and (2) at the front, one equation for continuity and two equations for momentum conservation. We suppose the front to be a mobile jump, with longitudinal velocity varying more rapidly than transverse velocity.We solve these equations by a finite difference method. This involves many topological problems, due to the actual position of the front, which is defined by its intersection with the reference grid (SI, YJ). In the near future our two directions of research will be testing the code on actual avalanches and improving it by trying to make it cheaper without impairing its accuracy.

Sign in / Sign up

Export Citation Format

Share Document