Rayleigh and Love Waves in Cladded Anistropic Medium

1990 ◽  
Vol 57 (2) ◽  
pp. 398-403 ◽  
Author(s):  
M. Bouden ◽  
S. K. Datta
Keyword(s):  
Anisotropic Medium ◽  
Guided Waves ◽  
Transversely Isotropic ◽  
Guided Wave ◽  
Fiber Reinforced Composites ◽  
Isotropic Layer ◽  
Reinforced Composites ◽  
Guided Wave Propagation ◽  
Rayleigh And Love Waves ◽  
Axis Of Symmetry

Guided waves in coated anisotropic medium are of interest in electronics. Also, in recent years, cladded fiber-reinforced composites are being developed for use as aerospace structures. This paper deals with guided wave propagation in a cladded or coated anisotropic medium. The cladding (coating) is assumed to be a thin isotropic layer, which is bonded to a transversely isotropic substrate with the axis of symmetry parallel to the layer. It is shown that the anisotropy of the substrate affects the dispersion behavior in a manner that is substantially different than in the case of isotropic substrate.

scholarly journals Temperature affected guided wave propagation in a composite plate complementing the Open Guided Waves Platform

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Jochen Moll ◽  
Christian Kexel ◽  
Serena Pötzsch ◽  
Marcel Rennoch ◽  
Axel S. Herrmann
Keyword(s):  
Wave Propagation ◽  
Temperature Effect ◽  
Guided Waves ◽  
Measurement Data ◽  
Guided Wave ◽  
Assessment Development ◽  
Cfrp Plate ◽  
Guided Wave Propagation ◽  
Wide Range ◽  
Technical Validation

Abstract The influence of temperature is regarded as particularly important for a structural health monitoring system based on ultrasonic guided waves. Since the temperature effect causes stronger signal changes than a typical defect, the former must be addressed and compensated for reliable damage assessment. Development of new temperature compensation techniques as well as the comparison of existing algorithms require high-quality benchmark measurements. This paper investigates a carbon fiber reinforced plastic (CFRP) plate that was fully characterized in previous research in terms of stiffness tensor and guided wave propagation. The same CFRP plate is used here for the analysis of the temperature effect for a wide range of ultrasound frequencies and temperatures. The measurement data are a contribution to the Open Guided Waves (OGW) platform: http://www.open-guided-waves.de. The technical validation includes initial results on the analysis of phase velocity variations with temperature and exemplary damage detection results using state-of-the-art signal processing methods that aim to suppress the temperature effect.

scholarly journals Numerical and Experimental Investigation of Guided Wave Propagation in a Multi-Wire Cable

2019 ◽  
Vol 9 (5) ◽  
pp. 1028 ◽  
Author(s):  
Pengfei Zhang ◽  
Zhifeng Tang ◽  
Fuzai Lv ◽  
Keji Yang
Keyword(s):  
Wave Energy ◽  
Guided Waves ◽  
Wave Structure ◽  
Excitation Power ◽  
Dispersion Analysis ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Mechanical Coupling ◽  
Guided Wave Propagation ◽  
Contact Acoustic Nonlinearity

Ultrasonic guided waves (UGWs) have attracted attention in the nondestructive testing and structural health monitoring (SHM) of multi-wire cables. They offer such advantages as a single measurement, wide coverage of the acoustic field, and long-range propagation ability. However, the mechanical coupling of multi-wire structures complicates the propagation behaviors of guided waves and signal interpretation. In this paper, UGW propagation in these waveguides is investigated theoretically, numerically, and experimentally from the perspective of dispersion and wave structure, contact acoustic nonlinearity (CAN), and wave energy transfer. Although the performance of all possible propagating wave modes in a multi-wire cable at different frequencies could be obtained by dispersion analysis, it is ineffective to analyze the frequency behaviors of the wave signals of a certain mode, which could be analyzed using the CAN effect. The CAN phenomenon of two mechanically coupled wires in contact was observed, which was demonstrated by numerical guided wave simulation and experiments. Additionally, the measured guided wave energy of wires located in different layers of an aluminum conductor steel-reinforced cable accords with the theoretical prediction. The model of wave energy distribution in different layers of a cable also could be used to optimize the excitation power of transducers and determine the effective monitoring range of SHM.

The effect of transverse isotropy on isotropic traveltime inversion of vertical seismic profile data—A modeling study

Geophysics ◽  
1990 ◽  
Vol 55 (9) ◽  
pp. 1235-1241 ◽  
Author(s):  
Jan Douma
Keyword(s):  
Transverse Isotropy ◽  
Transversely Isotropic ◽  
Anisotropic Media ◽  
Vertical Axis ◽  
Seismic Profile ◽  
Isotropic Layer ◽  
Low Velocity ◽  
Traveltime Inversion ◽  
Axis Of Symmetry ◽  
Transversely Isotropic Layer

Traveltime inversion of multioffset VSP data can be used to determine the depths of the interfaces in layered media. Many inversion schemes, however, assume isotropy and consequently may introduce erroneous structures for anisotropic media. Synthetic traveltime data are computed for layered anisotropic media and inverted assuming isotropic layers. Only the interfaces between these layers are inverted. For a medium consisting of a horizontal isotropic low‐velocity layer on top of a transversely isotropic layer with a horizontal axis of symmetry (e.g., anisotropy due to aligned vertical cracks), 2-D isotropic inversion results in an anticline. For a given axis of symmetry the form of this anticline depends on the azimuth of the source‐borehole direction. The inversion result is a syncline (in 3-D a “bowl” structure), regardless of the azimuth of the source‐borehole direction for a vertical axis of symmetry of the transversely isotropic layer (e.g., anisotropy due to horizontal bedding).

Ultrasonic Guided Wave Testing of Finned Tubing

2015 ◽  
Author(s):  
Owen M. Malinowski ◽  
Matthew S. Lindsey ◽  
Jason K. Van Velsor
Keyword(s):  
Wave Propagation ◽  
Guided Waves ◽  
Tube Wall ◽  
Guided Wave ◽  
Ultrasonic Guided Waves ◽  
Complex Nature ◽  
Inspection Method ◽  
Ultrasonic Guided Wave ◽  
Guided Wave Propagation ◽  
Wave Modes

In the past few decades, ultrasonic guided waves have been utilized more frequently Non-Destructive Testing (NDT); most notably, in the qualitative screening of buried piping. However, only a fraction of their potential applications in NDT have been fully realized. This is due, in part, to their complex nature, as well as the high level of expertise required to understand and utilize their propagation characteristics. The mode/frequency combinations that can be generated in a particular structure depend on geometry and material properties and are represented by the so-called dispersion curves. Although extensive research has been done in ultrasonic guided wave propagation in various geometries and materials, the treatment of ultrasonic guided wave propagation in periodic structures has received little attention. In this paper, academic aspects of ultrasonic guided wave propagation in structures with periodicity in the wave vector direction are investigated, with the practical purpose of developing an ultrasonic guided wave based inspection technique for finned tubing. Theoretical, numerical, and experimental methods are employed. The results of this investigation show excellent agreement between theory, numerical modeling, and experimentation; all of which indicate that ultrasonic guided waves will propagate coherently in finned tube only if the proper wave modes and frequencies are selected. It is shown that the frequencies at which propagating wave modes exist can be predicted theoretically and numerically, and depend strongly on the fin geometry. Furthermore, the results show that these propagating wave modes are capable of screening for and identifying the axial location of damage in the tube wall, as well as separation of the fins from the tube wall. The conclusion drawn from these results is that Guided Wave Testing (GWT) is a viable inspection method for screening finned tubing.

The Effect of Debonding Angle on the Reduction of Effective Moduli of Particle and Fiber-Reinforced Composites

2002 ◽  
Vol 69 (3) ◽  
pp. 292-302 ◽  
Author(s):  
Y. H. Zhao ◽  
G. J. Weng
Keyword(s):  
Transversely Isotropic ◽  
Fiber Composites ◽  
Fiber Reinforced Composites ◽  
Anisotropic Damage ◽  
Reinforced Composites ◽  
Effective Moduli ◽  
Loading Mode ◽  
Interfacial Cracks ◽  
The Matrix ◽  
Composite Stiffness

In an effort to uncover the effect of interfacial partial debonding on the reduction of composite stiffness, a reduced moduli approach is proposed for the fictitious inclusions which are used to replace the original partially debonded inclusions. The fictitious inclusions are now perfectly bonded to the matrix and any micromechanical theory can be called upon to estimate the moduli of the composite. Using the volume of the inclusion directly beneath the interfacial cracks under the considered loading mode as a measure of damage, a set of anisotropic damage parameters is established in terms of the debonding angle, providing the reduced moduli for the fictitious inclusions. Specific considerations include debonding on the top and bottom of spheres and prolate inclusions, debonding on the lateral surface of spheres and oblate inclusions, and debonding on the top and bottom of circular fibers and elliptic cylinders. The reductions of the five transversely isotropic moduli for the partially debonded particle composites and the nine orthotropic moduli for the partially debonded fiber composites are examined as the debonding angle increases. The theory is also compared with some finite element results, and it suggests that the concept proposed to estimate the reduced moduli of the fictitious inclusions is a viable one.

scholarly journals Scanning anisotropy parameters in complex media

Geophysics ◽  
2011 ◽  
Vol 76 (2) ◽  
pp. U13-U22 ◽  
Author(s):  
Tariq Alkhalifah
Keyword(s):  
Anisotropic Medium ◽  
Homogeneous Medium ◽  
Transversely Isotropic ◽  
Transient Behavior ◽  
Complex Media ◽  
Linear Partial Differential Equations ◽  
Anisotropy Parameters ◽  
Axis Of Symmetry ◽  
Ti Media ◽  
Taylor’S Series

Parameter estimation in an inhomogeneous anisotropic medium offers many challenges; chief among them is the trade-off between inhomogeneity and anisotropy. It is especially hard to estimate the anisotropy anellipticity parameter η in complex media. Using perturbation theory and Taylor’s series, I have expanded the solutions of the anisotropic eikonal equation for transversely isotropic (TI) media with a vertical symmetry axis (VTI) in terms of the independent parameter η from a generally inhomogeneous elliptically anisotropic medium background. This new VTI traveltime solution is based on a set of precomputed perturbations extracted from solving linear partial differential equations. The traveltimes obtained from these equations serve as the coefficients of a Taylor-type expansion of the total traveltime in terms of η. Shanks transform is used to predict the transient behavior of the expansion and improve its accuracy using fewer terms. A homogeneous medium simplification of the expansion provides classical nonhyperbolic moveout descriptions of the traveltime that are more accurate than other recently derived approximations. In addition, this formulation provides a tool to scan for anisotropic parameters in a generally inhomogeneous medium background. A Marmousi test demonstrates the accuracy of this approximation. For a tilted axis of symmetry, the equations are still applicable with a slightly more complicated framework because the vertical velocity and δ are not readily available from the data.

Analysis of Corrosion Areas in Pipelines Using Guided Wave Propagation: Numerical Simulations and Experimental Tests

2013 ◽  
Author(s):  
Florin Turcu ◽  
Francesco Bertoncini ◽  
Giuseppe Giunta ◽  
Marco Raugi
Keyword(s):  
Wave Propagation ◽  
Numerical Methods ◽  
Numerical Simulations ◽  
Guided Waves ◽  
Experimental Tests ◽  
Field Testing ◽  
Guided Wave ◽  
Coherent Noise ◽  
Guided Wave Propagation ◽  
Integrity Issue

Guided Waves (GW) have become widely used for the inspection of unpiggable and inaccessible pipelines because of the presence of coating, because of their position or because they are buried. Among the possible anomalies, corrosion is the main integrity issue affecting pipelines. The effect that corrosion has on guided wave propagation is attenuation and increased coherent noise when it is generalized or reflection when corrosion is localized. In this paper, the possibility to characterize corrosion areas affecting pipelines through long range guided wave inspection or monitoring is investigated. With this purpose field testing was performed and the results were used for the validation of numerical methods able to simulate the phenomenon.

Guided Wave Propagation and Interaction with Damage in Tubular Structures

2008 ◽  
Vol 32 ◽  
pp. 289-292
Author(s):  
Ye Lu ◽  
Lin Ye ◽  
Dong Wang ◽  
Guang Meng
Keyword(s):  
Wave Propagation ◽  
Wave Scattering ◽  
Guided Waves ◽  
Guided Wave ◽  
Tube Surface ◽  
Tubular Structures ◽  
Active Sensor ◽  
Guided Wave Propagation ◽  
Rectangular Tube ◽  
Signal Correlation

A piezoelectric active sensor network is configured to collect the wave scattering from a throughthickness hole on an aluminium rectangular tube. It is found that guided waves are capable of propagating across the tube edges, while keeping the sensitivity to the damage even not on surfaces where the actuator and sensor are located. Signal correlation between the intact and damaged structure is evaluated and the probability distribution of damage is thus achieved on the unfolded tube surface.

Sign in / Sign up

Export Citation Format

Share Document