Performance Prediction of a Sub-Slab Heat Exchanger for Geothermal Heat Pumps

1998 ◽  
Vol 120 (4) ◽  
pp. 282-288 ◽  
Author(s):  
K. Den Braven ◽  
E. Nielson
Keyword(s):  
Soil Temperature ◽  
Heat Pump ◽  
Flow Direction ◽  
Heat Pumps ◽  
Heat Extraction ◽  
Fluid Temperature ◽  
Geothermal Heat ◽  
Pump System ◽  
Pump Operation ◽  
Heat Pump System

A large portion of the installation cost of a ground-coupled heat pump system is for the excavation necessary for ground coil placement. One possible method of reducing this cost is to place the ground coils beneath the slab floor of the building. This configuration of ground coil placement has not been specifically addressed in previous research. Freezing of the soil must be avoided in such a system. To simulate the temperature response of the surrounding soil to heat pump operation, a computer model was developed which incorporates line source theory in the form of a system of rings. The fluid temperature change along the length of the coil was used to determine the distribution of the ground load throughout the ring system. The model includes an adiabatic upper boundary, seasonal soil temperature variation, and thermal interference throughout the system. Using these results, the minimum soil temperature over a season was predicted. Based on these results, design recommendations for ground coil installation are provided based on available area, soil type, heat extraction rate, depth of coil beneath the slab floor, and depth of slab floor below grade. These include recommendations for pipe spacing, flow direction, and a method to determine whether this type of system is feasible for installation in a particular location.

An Economical Analysis on a Solar Greenhouse Integrated Solar Assisted Geothermal Heat Pump System

2005 ◽  
Vol 128 (1) ◽  
pp. 28-34 ◽  
Author(s):  
Onder Ozgener ◽  
Arif Hepbasli
Keyword(s):  
Heat Pump ◽  
Cooling System ◽  
Heat Pumps ◽  
Renewable Energy Resources ◽  
Ahp Method ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Economical Analysis ◽  
Geothermal Heat Pump

The main objective in doing the present study is twofold, namely (i) to review briefly the utilization of geothermally heated greenhouses and geothermal heat pumps in Turkey, since the system studied utilizes both renewable energy resources and (ii) to present the Analytical Hierarchy Process (AHP) as a potential decision making method for use in a greenhouse integrated solar assisted geothermal heat pump system (GISAGHPS), which was installed in the Solar Energy Institute of Ege University, Izmir, Turkey. This investigation may also be regarded as the one of the limited studies on the application of the AHP method to GISAGHPs, as no studies on the GISAGHPS have appeared in the literature. In this context, an economic analysis is performed based on the life cycle costing technique first. The results are then evaluated by applying the AHP method to a study, which is a comparative study on the GISAGHPS and split system. The results indicated that the GISAGHPS is economically preferable to the conventional split heating/cooling system under Turkey’s conditions.

scholarly journals Human-induced load on the environment when using geothermal heat pump wells

2020 ◽  
Vol 29 (1) ◽  
pp. 57-68
Author(s):  
Sergii V. Goshovskyi ◽  
Oleksii V. Zurian
Keyword(s):  
Soil Temperature ◽  
Heat Pump ◽  
Heat Load ◽  
Geothermal Field ◽  
Heat Energy ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Geothermal Heat Exchanger ◽  
Geothermal Heat Pump

The research is aimed to study the process of change in temperature mode dynamics for the Earth subsurface layer when heat is extracted with geothermal heat pump systems, reveal and disclose specifics of effect on the ecology caused by technologies using geothermal resources and give practical recommendations regarding further development of methods for designing heat pumps using low potential heat energy of soil based on the long-term forecast and efficacy assessment. Mathematical statistics and mathematical model methods were applied for assessment of economic and environmental effects. Methods based on principles of the theory of thermal conductivity, hydromechanics, theory of differential equations and mathematical analysis were applied for calculation of proposed systems and review of field observation findings. The authors had developed for research purposes an experimental geothermal heat pump system consisting of four structurally connected geothermal wells, each with installed U-shaped twin collectors of 200 m overall length, and a heat pump of 14 kW capacity with a heat energy battery for 300 L connected to the building heat-supply system. They also created a computer data archivation and visualisation system and devised a research procedure. The paper provides assessment of the effect caused by changes in the process operation mode of the heat pump system on the soil temperature near the geothermal well. As a result, the authors have found that the higher the intensity of heat energy extraction, the lower the soil temperature near the geothermal heat exchanger, in proportion to the load on the system. Moreover, it has been determined by experimental means that at critical loads on the geothermal heat exchanger the soil temperature is unable to keep up with regeneration and may reach negative values. The research also determined relation between inservice time and season of the system operation and temperature fluctuations of geothermal field. For example, it has been found by experimental means that the heat flow from the well is spread radially, from the well axis to its borders. Additionally, it has been proved that depending on the heat load value, the bed temperature is changed after the time of the first launch. For example, the geothermal field temperature has changed from the time of the first launch during 1-year operation by 0.5 °С in average. The research has proved that depending on the heat load value, under seasonal operation (heating only or cooling only) of the system, the soil temperature has decreased for five years by 2.5 °С and switched to quasi-steady state, meanwhile, stabilisation of the geothermal field in the state under 1-year operation (heating and cooling) occurred yet in the 2nd year of operation. In conclusion, the paper reasonably states that geothermal heat pump systems using vertical heat exchangers installed into the wells put no significant human-induced load on the environment. At the same time, still relevant are issues of scientific approach to development of the required configuration of the geothermal collector, methodology for its optimal placement and determination of efficacy depending on operation conditions.

scholarly journals Implementation of a geothermal heat pump system in a solar passive house

2019 ◽  
Vol 85 ◽  
pp. 07014
Author(s):  
Gheorghe Ilisei ◽  
Tiberiu Catalina ◽  
Marian Alexandru ◽  
Robert Gavriliuc
Keyword(s):  
Heat Pump ◽  
Electricity Consumption ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Passive House ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Major Index ◽  
Passive Houses

Underground energy sources are becoming increasingly popular and now geothermal heat pumps are frequently used to heat/cool different types of buildings, including for solar passive houses. This article aims at giving a contribution in the development of the thermal modelling of borehole heat storage systems, investigating the possibility of a GSHP (ground source heat pump) implementation with vertical boreholes in a solar passive house. A case study analysing a residential solar passive house is presented as a suitable modelling tool for the estimation of the thermal behaviour of GSHP systems by combining the outcome from different modelling programs. The software DesignBuilder, Earth Energy Designer and a sizing method for borehole’s length are used for producing the numerical results. The results highlight that the length of the borehole, a major index in estimating the system’s cost, is directly influenced by fundamental variables like thermal conductivity of grout or soil. Additionally, correlations between these parameters and the coefficient of performance of GSHP were made. Furthermore, the length of borehole is very important as it is responsible for almost half of the total installation cost and triggered a difference in electricity consumption of the GSHP up to 14%.

DETERMINING THE PROFITABILITY OF GREENHOUSE ELECTROTECHNOLOGIES: A MODELING APPROACH

HortScience ◽  
1994 ◽  
Vol 29 (4) ◽  
pp. 249a-249
Author(s):  
Eric A. Lavoie ◽  
Damien de Halleux ◽  
André Gosselin ◽  
Jean-Claude Dufour
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Water System ◽  
Heat Pumps ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Artificial Lighting ◽  
Hot Air ◽  
Marketable Fruit

The main objective of this research was to produce a simulated model that permitted the evaluation of operating costs of commercial greenhouse tomato growers with respect to heating methods (hot air, hot water, radiant and heat pumps) and the use of artificial lighting for 1991 and 1992. This research showed that the main factors that negatively influence profitability were energy consumption during cold periods and the price of tomatoes during the summer season. The conventional hot water system consumed less energy than the heat pump system and produced marketable fruit yields similar to those from the heat pump system. The hot water system was generally more profitable in regards to energy consumption and productivity. Moreover, investment costs were less; therefore, this system gives best overall financial savings. As for radiant and hot air systems, their overall financial status falls between that of the hot water system and the heat pump. The radiant system proved to be more energy efficient that the hot air system, but the latter produced a higher marketable fruit yield over the 2-year study.

scholarly journals Analysis of Heat Exchange Rate for Low-Depth Modular Ground Heat Exchanger through Real-Scale Experiment

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1893
Author(s):  
Kwonye Kim ◽  
Jaemin Kim ◽  
Yujin Nam ◽  
Euyjoon Lee ◽  
Eunchul Kang ◽  
...  
Keyword(s):  
Exchange Rate ◽  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Pump ◽  
Heat Extraction ◽  
Ground Heat Exchanger ◽  
Pump System ◽  
Heat Pump System ◽  
Scale Experiment ◽  
Real Scale

A ground source heat pump system is a high-performance technology used for maintaining a stable underground temperature all year-round. However, the high costs for installation, such as for boring and drilling, is a drawback that prevents the system to be rapidly introduced into the market. This study proposes a modular ground heat exchanger (GHX) that can compensate for the disadvantages (such as high-boring/drilling costs) of the conventional vertical GHX. Through a real-scale experiment, a modular GHX was manufactured and buried at a depth of 4 m below ground level; the heat exchange rate and the change in underground temperatures during the GHX operation were tracked and calculated. The average heat exchanges rate was 78.98 W/m and 88.83 W/m during heating and cooling periods, respectively; the underground temperature decreased by 1.2 °C during heat extraction and increased by 4.4 °C during heat emission, with the heat pump (HP) working. The study showed that the modular GHX is a cost-effective alternative to the vertical GHX; further research is needed for application to actual small buildings.

The design of a seasonal heat storage system with a geothermal heat pump for a residential building in Tehran

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Akbar Alidadi Shamsabadi ◽  
Mehdi Jahangiri ◽  
Tayebeh Rezaei ◽  
Rouhollah Yadollahi Farsani ◽  
Ali Seryani ◽  
...  
Keyword(s):  
Heat Pump ◽  
Heating System ◽  
Coefficient Of Performance ◽  
Maximum Temperature ◽  
Software Environment ◽  
Geothermal Heat ◽  
Pump System ◽  
Matlab Software ◽  
Content Type ◽  
Heat Pump System

Purpose In this study, a solar water heating system along with a seasonal thermal energy storage and a heat pump is designed for a villa with an area of 192 m2 in Tehran, the capital of Iran. Design/methodology/approach According to the material and the area of the residential space, the required heating of the building was calculated manually and then the thermodynamic analysis of the system and simulation was done in MATLAB software. Finally, regarding the waste of system, an efficient solar heating system, providing all the required energy to heat the building, was obtained. Findings The surface area of the solar collector is equal to 46 m2, the capacity of the tank is about 2,850 m3, insulation thickness stands at 55 cm and the coefficient of performance in required heat pump is accounted to about 9.02. Also, according to the assessments, the maximum level of received energy by the collector in this system occurs at a maximum temperature of 68ºC. Originality/value To the best of the authors’ knowledge, in the present work, for the first time, using mathematical modeling and analyzing of the first and second laws of thermodynamics, as well as using of computational code in MATLAB software environment, the solar-assisted ground source heat pump system is simulated in a residential unit located in Tehran.

scholarly journals Designing and Optimizing Heat Storage of a Solar-Assisted Ground Source Heat Pump System in China

2020 ◽  
Vol 2020 ◽  
pp. 1-18 ◽  
Author(s):  
Yan Gao ◽  
Zhi Sun ◽  
Xinxing Lin ◽  
Chuang Wang ◽  
Zongyu Sun ◽  
...  
Keyword(s):  
Soil Temperature ◽  
Heat Pump ◽  
Solar Collector ◽  
Heat Storage ◽  
Ground Source Heat Pump ◽  
Cold Region ◽  
Annual Average ◽  
Pump System ◽  
Heat Pump System ◽  
Ground Source

The cold accumulation problem can lead to performance degradation of heat pumps. This paper presents the design and optimization of a solar-assisted storage system to solve this issue. A ground source heat pump (GSHP) project was established using the transient system simulation program (TRNSYS) based on a ground heat exchange theoretical model, which was validated by a previously established experiment in Beijing. The Beijing, Harbin, and Zhengzhou regions were used in numerical simulations to represent three typical cities where buildings require space heating (a cold region, a severe cold region, and a hot summer and cold winter region, respectively). System performance was simulated over periods of ten years. The simulation results showed that the imbalance efficiencies in the Beijing, Harbin, and Zhengzhou regions are 55%, 79%, and 38%, respectively. The annual average soil temperature decreases 7.3°C, 11.0°C, and 5.3°C during ten years of conventional GSHP operation in the Beijing, Harbin, and Zhengzhou regions, respectively. Because of the soil temperature decrease, the minimum heating coefficient of performance (COP) values decrease by 23%, 46%, and 11% over the ten years for GSHP operation in these three regions, respectively. Moreover, the simulation data show that the soil temperature would still be decreasing if based on the previous solar energy area calculation method. Design parameters such as the solar collector size are optimized for the building load and average soil temperature in various cold regions. Long-term operation will test the matching rate of the compensation system with the conventional GSHP system. After the system is optimized, the solar collector area increases of 20% in the Beijing region, 25% in the Harbin region, and 15% in the Zhengzhou region could help to maintain the annual average soil temperature balance. The optimized system could maintain a higher annual average COP because of the steady soil temperature. It provides a method for the design of a solar collector area which needs to be determined in the seasonal heat storage solar ground source heat pump system.

scholarly journals Numerical evaluation of the performance of a single-well groundwater source heat pump system in Beijing, China

2019 ◽  
Vol 38 (1) ◽  
pp. 201-221 ◽  
Author(s):  
Tianfu Xu ◽  
Fengyu Li ◽  
Bo Feng ◽  
Guanhong Feng ◽  
Zhenjiao Jiang
Keyword(s):  
Heat Transport ◽  
Heat Pump ◽  
Transport Model ◽  
Heat Pumps ◽  
Transport Processes ◽  
Pump System ◽  
Heat Pump System ◽  
Single Well ◽  
Groundwater Source ◽  
Beijing China

Shallow geothermal energy is stable and clean. Using a heat pump to produce groundwater and realize heating and cooling can effectively prevent haze and reduce energy consumption. To reduce engineering costs, many buildings in Beijing, China, plan to utilize single-well groundwater source heat pumps. Numerical modeling is an effective way to gain an understanding of thermal transport processes. However, wellbore-reservoir coupling and the uncertainty of productivity due to geological parameters make simulation difficult. A wellbore-reservoir-integrated fluid and heat transport model is defined by T2Well simulator to predict the productivity of a typical single-well system, with consideration of complex geological factors. The model is validated by the analytical model developed in Beijing, China. The fluid processes in the wellbore are described by 1 D non-Darcy flow, and the reservoir 3 D fluid and heat transport processes are calculated. Six crucial factors satisfying a random distribution are used, and for a single well that can supply heat for an area of 9000 m2, the output temperature during the heating season ranges from 11°C to 15°C.

Optimization and energy-economic assessment of a geothermal heat pump system

2020 ◽  
Vol 133 ◽  
pp. 110282 ◽  
Author(s):  
Pooya Farzanehkhameneh ◽  
M. Soltani ◽  
Farshad Moradi Kashkooli ◽  
Masoud Ziabasharhagh
Keyword(s):  
Heat Pump ◽  
Economic Assessment ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Geothermal Heat Pump
Sign in / Sign up

Export Citation Format

Share Document