Performance of a Heat Pipe Solar Collector

1998 ◽  
Vol 120 (1) ◽  
pp. 51-59 ◽  
Author(s):  
K. A. R. Ismail ◽  
M. M. Abogderah
Keyword(s):  
Heat Exchange ◽  
Flat Plate ◽  
Heat Pipe ◽  
Solar Collector ◽  
Energy Transport ◽  
Heat Pipes ◽  
Experimental Results ◽  
Working Fluid ◽  
Theoretical Predictions ◽  
Flat Plate Solar Collector

This paper presents a comparative study between theoretical predictions and experimental results of a flat-plate solar collector with heat pipes. The theoretical model for the heat pipe solar collector is based upon the method by Duffie and Beckman(1980), modified to use heat pipes for energy transport. The methanol filled heat pipes are self-contained devices whose evaporators are inserted under pressure in the flat plate of the solar collector and the heat exchange is carried out at their condensers. The evaporators contain a wick of one mesh layer to ensure a better distribution of the working fluid. The condensers are wickless and inclined 15 deg more than the inclination of the evaporators to facilitate the return of the condensate to the evaporators. The time constant of the heat pipe solar collector was calculated and found to be about 23 minutes. Also presented in this paper are comparative experimental results of the proposed solar collector and a conventional commercial solar collector. The two collectors were tested simultaneously. The instantaneous efficiencies of the heat pipe solar collector are lower than the conventional collector in the morning and higher when the heat pipes reach their operating temperatures.

scholarly journals Numerical study of flat plate solar collector performance with square shape wicked evaporator

2019 ◽  
Vol 12 (2) ◽  
pp. 90-97
Author(s):  
Basil Noori Merzah ◽  
Majid H. Majeed ◽  
Fouad A. Saleh
Keyword(s):  
Flat Plate ◽  
Heat Pipe ◽  
Flow Rate ◽  
Solar Collector ◽  
Numerical Study ◽  
Charge Ratio ◽  
Working Fluid ◽  
Evaporator Section ◽  
Fill Charge Ratio ◽  
Flat Plate Solar Collector

In this work, a system of a heat pipe is implemented to improve the performance of flat plate solar collector. The model is represented by square shape portion of the evaporator section of wicked heat pipe with a constant total length of 510 mm, and the evaporator section inclined by an angle of 30o. In this models the evaporator, adiabatic and condenser lengths are 140mm, 140mm, and 230mm respectively. The omitted energies from sunlight simulator are 200, 400, 600, 800 and 1000 W/m2 which is close to the normal solar energy in Iraq. The working fluid for all models is water with fill charge ratio of 240%. The efficiency of the solar collector is investigated with three values of condenser inlet water temperatures, namely (12, 16 and 20o C). The numerical result showed an optimum volume flow rate of cooling water in condenser at which the efficiency of collector is a maximum. This optimum agree well with the ASHRAE standard volume of flow rate for conventional tasting for flat plate solar collector. When the radiation incident increases the thermal resistance of wicked heat pipe is decreases, where the heat transfer from the evaporator to condenser increases. The numerical results showed the performance of solar collector with square shape evaporator greater than other types of evaporator as a ratio 15 %.

Optimization of a wickless heat pipe flat plate solar collector

1999 ◽  
Vol 40 (18) ◽  
pp. 1949-1961 ◽  
Author(s):  
H.M.S. Hussein ◽  
M.A. Mohamad ◽  
A.S. El-Asfouri
Keyword(s):  
Flat Plate ◽  
Heat Pipe ◽  
Solar Collector ◽  
Flat Plate Solar Collector

Investigating the Effect of Al2O3/Water Nanofluid on the Efficiency of a Thermosyphon Flat-Plate Solar Collector

2016 ◽  
Author(s):  
Mohamed Nabeel A. Negm ◽  
Ahmed A. Abdel-Rehim ◽  
Ahmed A. A. Attia
Keyword(s):  
Flat Plate ◽  
Solar Collector ◽  
Fossil Fuels ◽  
Energy Conversion Efficiency ◽  
High Energy ◽  
Green Energy ◽  
Working Fluid ◽  
Steady Increase ◽  
Solar Collectors ◽  
Flat Plate Solar Collector

The world is still dependent on fossil fuels as a continuous and stable energy source, but rising concerns for depletion of these fuels and the steady increase in demand for clean “green” energy have led to the rapid growth of the renewable energy field. As one of the most available energy sources with high energy conversion efficiency, solar energy is the most prominent of these energies as it also has the least effect on the environment. Flat plate collectors are the most common solar collectors, while their efficiency is limited by their absorber’s effectiveness in energy absorption and the transfer of this energy to the working fluid. The efficiency of flat plate solar collectors can be increased by using nanofluids as the working fluid. Nanofluids are a relatively recent development which can greatly enhance the thermophysical properties of working fluids. In the present study, the effect of using Al2O3/Water nanofluid as the working fluid on the efficiency of a thermosyphon flat-plate solar collector was experimentally investigated. The results of this experiment show an increase in efficiency when using nanofluids as the working fluid compared to distilled water. It was found that Al2O3/water nanofluids are a viable enhancement for the efficiency of flat-plate solar collectors.

scholarly journals Heat transfer in a low latitude flat-plate solar collector

2012 ◽  
Vol 16 (2) ◽  
pp. 583-591
Author(s):  
C.O.C. Oko ◽  
S.N. Nnamchi
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Solar Collector ◽  
Design Parameters ◽  
Working Fluid ◽  
Fluid Temperature ◽  
Port Harcourt ◽  
Collector Efficiency ◽  
One Year ◽  
Flat Plate Solar Collector

Study of rate of heat transfer in a flat-plate solar collector is the main subject of this paper. Measurements of collector and working fluid temperatures were carried out for one year covering the harmattan and rainy seasons in Port Harcourt, Nigeria, which is situated at the latitude of 4.858oN and longitude of 8.372oE. Energy balance equations for heat exchanger were employed to develop a mathematical model which relates the working fluid temperature with the vital collector geometric and physical design parameters. The exit fluid temperature was used to compute the rate of heat transfer to the working fluid and the efficiency of the transfer. The optimum fluid temperatures obtained for the harmattan, rainy and yearly (or combined) seasons were: 317.4, 314.9 and 316.2 [K], respectively. The corresponding insolation utilized were: 83.23, 76.61 and 79.92 [W/m2], respectively, with the corresponding mean collector efficiency of 0.190, 0.205 and 0.197 [-], respectively. The working fluid flowrate, the collector length and the range of time that gave rise to maximum results were: 0.0093 [kg/s], 2.0 [m] and 12PM - 13.00PM, respectively. There was good agreement between the computed and the measured working fluid temperatures. The results obtained are useful for the optimal design of the solar collector and its operations.

scholarly journals Numerical Investigation to Asses and Optimize Performance of Flat Plate Solar Collector by Using Different Working Fluid

2021 ◽  
Vol 87 (2) ◽  
pp. 44-55
Author(s):  
Yussra Malalah Abdula ◽  
Gadeer Salim ◽  
Salman K
Keyword(s):  
Numerical Model ◽  
Flat Plate ◽  
Solar Collector ◽  
Current Model ◽  
Effective Means ◽  
Industrial Applications ◽  
Working Fluid ◽  
Literature Study ◽  
Maximum Temperatures ◽  
Flat Plate Solar Collector

Sustainable energy becomes an optimal alternative to overcome environmental pollution economical cost of fossil fuel. One of the most effective means to invest solar radiation is flat plate solar collectors. A study carried out to optimize and assess the performance of flat plate solar collector (FPSC) for domestic and industrial applications in the Iraq climate. A 3D numerical model of FPSC has modeled by ANSYS19, CFD tool has been used to investigate thermal transfer through FPSC based on different working fluid. Water, and nanofluid of water/copper nanomaterials were used as working fluid with three different concentrations levels, 0.011 %, 0.055%, and 0,101 %. The velocity of water was 0.3, and 0.5 m/sec respectively. The result of the numerical model was compared with a literature study to prove the reliability of the current model. The result of the current study indicated that, adding Cu nanoparticular to the working fluid enhanced temperatures outlet of FPSC. Also, maximum temperatures can be achieved by reducing the velocity value.

Exergy Analysis of a Flat Plate Solar Collector With Grooved Absorber Tube Configuration Using Aqueous ZnO–Ethylene Glycol

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Yash Kashyap ◽  
Apurva Singh ◽  
Y. Raja Sekhar
Keyword(s):  
Ethylene Glycol ◽  
Flat Plate ◽  
Solar Collector ◽  
Volume Fraction ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Plain Tube ◽  
Collector Temperature ◽  
Grooved Tube ◽  
Flat Plate Solar Collector

In this study, the exergetic performance of a flat plate solar collector (FPSC) setup with ZnO-based ethylene glycol (EG)/water nanofluid as a working fluid has been evaluated against that of EG/water. As a passive means to augment the rate of heat transfer, internally grooved tubes of two different pitches (e = 0.43 and e = 0.44) have been examined and compared against the performance of plain tube. The mass flow rate was fixed at 0.015 kg/s and the volume fraction of ZnO nanoparticles is ф = 0.02% v/v. The results indicate an enhancement in exergy efficiency of 44.61% when using the grooved tube (e = 0.44) against plain tube without the nanofluid and 39.17% when nanofluid is used. Using the nanofluid enhanced the exergy efficiency of the FPSC by a maximum of 73.81%. Maximum exergy efficiency obtained was 5.95% for grooved tube (e = 0.44) with nanofluid as working fluid and is in good agreement with previous literature. Exergy destruction/irreversibility due to temperature differences and heat flow within the system has been reported. Sun-collector temperature difference accounts for nearly 86–94% of the irreversibility. The results for thermal efficiency of this experimental setup have been published and summarized in this study for reference.

Fabrication and Testing of SOG Structure Flat Heat Pipes with Triangle Grooves

2011 ◽  
Vol 483 ◽  
pp. 58-61 ◽  
Author(s):  
Xiao Wei Liu ◽  
Chao Wang ◽  
Tian Han ◽  
Tian Dong
Keyword(s):  
Thermal Conductivity ◽  
Heat Pipe ◽  
Glass Structure ◽  
Heat Pipes ◽  
Experimental Results ◽  
Working Fluid ◽  
Micro Heat Pipe ◽  
Vacuum Atmosphere

A new kind of charging and sealing method for SOG (silicon on glass) structure micro heat pipe with triangular grooves is investigated. MHP (micro heat pipe) is fully charged in a vacuum atmosphere which is useful for preventing air intermingle. Experimental results shows that when the fill ration of working fluid is about 35%, thermal conductivity of MHP with ethanol as its working fluid has an improvement of 19% compared to empty MHP.

Sign in / Sign up

Export Citation Format

Share Document