Experimental Study of the Flow in the Suction Pipe of a Centrifugal Pump at Partial Flow Rates in Unsteady Conditions

1999 ◽  
Vol 121 (3) ◽  
pp. 291-295 ◽  
Author(s):  
S. Bolpaire ◽  
J. P. Barrand
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Static Pressure ◽  
Pressure Measurements ◽  
Flow Rates ◽  
Suction Pipe ◽  
Start Up ◽  
Test Loop ◽  
Fast Start ◽  
Operational Range

The operational range and the performances of pumps are limited by the occurrence of backflow and prerotation in the suction pipe as the flow rate is reduced. This paper presents the study of static pressure measurements and visualizations in the suction pipe, near the inlet of a centrifugal pump, at partial flow rates, in steady conditions, and during a fast start-up of the pump. The tests were carried out in water on the DERAP© test loop of the ENSAM Lille laboratory. Standard methods allowed to determine the recirculation critical flow rate. A visualization method showed that the axial extent of the recirculation and the prerotation with the flow rate is considerably reduced during a fast start-up compared to steady conditions.

Experimental Investigation of Pressure Fluctuations on Inner Wall of a Centrifugal Pump

2019 ◽  
Vol 36 (4) ◽  
pp. 401-410 ◽  
Author(s):  
Xiao-Qi Jia ◽  
Bao-Ling Cui ◽  
Zu-Chao Zhu ◽  
Yu-Liang Zhang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Pressure Fluctuations ◽  
High Flow ◽  
Low Flow ◽  
Centrifugal Pumps ◽  
Flow Rates ◽  
Pressure Distributions ◽  
Blade Passing Frequency

Abstract Affected by rotor–stator interaction and unstable inner flow, asymmetric pressure distributions and pressure fluctuations cannot be avoided in centrifugal pumps. To study the pressure distributions on volute and front casing walls, dynamic pressure tests are carried out on a centrifugal pump. Frequency spectrum analysis of pressure fluctuation is presented based on Fast Fourier transform and steady pressure distribution is obtained based on time-average method. The results show that amplitudes of pressure fluctuation and blade-passing frequency are sensitive to the flow rate. At low flow rates, high-pressure region and large pressure gradients near the volute tongue are observed, and the main factors contributing to the pressure fluctuation are fluctuations in blade-passing frequency and high-frequency fluctuations. By contrast, at high flow rates, fluctuations of rotating-frequency and low frequencies are the main contributors to pressure fluctuation. Moreover, at low flow rates, pressure near volute tongue increases rapidly at first and thereafter increases slowly, whereas at high flow rates, pressure decreases sharply. Asymmetries are observed in the pressure distributions on both volute and front casing walls. With increasing of flow rate, both asymmetries in the pressure distributions and magnitude of the pressure decrease.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1991 ◽  
Author(s):  
Ronald D. Flack ◽  
Steven M. Miner ◽  
Ronald J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two directional laser velocimeter. Data presented includes radial, tangential, and cross product Reynolds stresses. Blade to blade profiles were measured at four circumferential positions and four radii within and one radius outside the four bladed impeller. The pump was tested in two configurations; with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40% to 106% of the design flow rate. Variation in profiles among the individual passages in the orbiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9% and exit turbulence intensities were 6%. For 40% flow capacity the values increased to 18% and 19%, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

Turbulence Measurements in a Centrifugal Pump With a Synchronously Orbiting Impeller

1992 ◽  
Vol 114 (2) ◽  
pp. 350-358 ◽  
Author(s):  
R. D. Flack ◽  
S. M. Miner ◽  
R. J. Beaudoin
Keyword(s):  
Centrifugal Pump ◽  
Reynolds Stress ◽  
Flow Rate ◽  
Cross Product ◽  
Design Flow ◽  
Low Flow ◽  
Rate Variation ◽  
Flow Rates ◽  
The Individual ◽  
Design Flow Rate

Turbulence profiles were measured in a centrifugal pump with an impeller with backswept blades using a two-directional laser velocimeter. Data presented include radial, tangential, and cross product Reynolds stresses. Blade-to-blade profiles were measured at four circumferential positions and four radii within and one radius outside the four-bladed impeller. The pump was tested in two configurations: with the impeller running centered within the volute, and with the impeller orbiting with a synchronous motion (ε/r2 = 0.016). Flow rates ranged from 40 to 106 percent of the design flow rate. Variation in profiles among the individual passages in the oribiting impeller were found. For several regions the turbulence was isotropic so that the cross product Reynolds stress was low. At low flow rates the highest cross product Reynolds stress was near the exit. At near-design conditions the lowest cross product stress was near the exit, where uniform flow was also observed. Also, near the exit of the impeller the highest turbulence levels were seen near the tongue. For the design flow rate, inlet turbulence intensities were typically 9 percent and exit turbulence intensities were 6 percent. For 40 percent flow capacity the values increased to 18 and 19 percent, respectively. Large local turbulence intensities correlated with separated regions. The synchronous orbit did not increase the random turbulence, but did affect the turbulence in the individual channels in a systematic pattern.

scholarly journals X-Ray Measurements in a Cavitating Centrifugal Pump During Fast Start-Ups

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
S. Duplaa ◽  
O. Coutier-Delgosha ◽  
A. Dazin ◽  
G. Bois
Keyword(s):  
Centrifugal Pump ◽  
Rocket Engine ◽  
Transient Behavior ◽  
Operating Conditions ◽  
Centrifugal Impeller ◽  
X Ray ◽  
Speed Increase ◽  
Start Up ◽  
Fast Start ◽  
Start Ups

The start-up of rocket engine turbopumps is generally performed in a few seconds or even less. It implies that these pumps reach their nominal operating conditions after a few rotations only. During the start-up, the flow evolution within the pump is governed by transient phenomena, based mainly on the flow rate and rotation speed increase. Significant pressure fluctuations, which may result in the development of cavitation, are observed. A centrifugal impeller whose transient behavior during start-ups has been detailed in a previous publication is considered. Three different cases of fast start-ups have been identified according the final operating point (Duplaa et al., 2010, “Experimental Study of a Cavitating Centrifugal Pump During Fast Start-Ups,” ASME J. Fluids Eng., 132(2), p. 021301). The aim of this paper is to analyze the evolution during the start-ups of the local amount of vapor in the blade to blade channels of the pump by fast X-ray imaging. This technique has enabled to calculate the time-evolution of the fluid density within the pump, which appears to be correlated with pressure time-evolutions. For each investigated start-up, X-ray measurements have been performed at three different sections of the impeller height. For each investigated start-up and section tested, measurements have been performed for several initial positions of the impeller, to estimate the measurement uncertainty, and to obtain records from different beam angles, like in tomography.

Flow at the Centrifugal Pump Impeller Exit With Circumferential Distortion of the Outlet Static Pressure

2004 ◽  
Vol 126 (1) ◽  
pp. 81-86 ◽  
Author(s):  
Soon-Sam Hong ◽  
Shin-Hyoung Kang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Total Pressure ◽  
Static Pressure ◽  
Mean Flow ◽  
Simple Method ◽  
Local Flow ◽  
Flow Angle ◽  
Flow Parameters ◽  
Relative Flow

The effects of circumferential outlet distortion of a centrifugal pump diffuser on the impeller exit flow were investigated. A fence with sinusoidal width variation was installed at the vaneless diffuser exit. The flow field was measured at the impeller exit with and without the fence, using a hot film probe and an unsteady pressure sensor. Flow parameters varied with the circumferential position and the mean flow parameters plotted against the local flow rate at each circumferential position showed loops along the quasi-steady curves, which were obtained from the result without the fence. Simple theoretical calculations were used to predict the velocity components at the impeller exit with the relative flow angle or total pressure assumed. Good result was obtained when the relative flow angle was assumed to vary quasi-steadily, not constant with the local flow rate. The radial velocity was also reasonably predicted when the total pressure was assumed to vary quasi-steadily. A simple method is proposed to predict the impeller exit flow with downstream blockage in two-step sequence: the first step deals with the diffuser alone to obtain static pressure distribution at the diffuser inlet, while the second step deals with the impeller alone to obtain velocity components distribution at the impeller exit.

scholarly journals A Study of the Flow Characteristics in the Inducer Bleed Slot of a Centrifugal Compressor

1996 ◽  
Author(s):  
P. A. Eynon ◽  
A. Whitfield ◽  
M. R. Firth ◽  
A. J. Parkes ◽  
R. Saxton
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Low Frequency ◽  
Flow Reversal ◽  
Flow Visualisation ◽  
Pressure Measurements ◽  
Flow Rates ◽  
Operating Range ◽  
Flow Pulsations ◽  
Inlet Duct

A broad operating range between surge and choke is so important for turbocharger compressors and many other applications that a vaneless diffuser, with its reduced efficiency, is usually adopted. With the demand for increased pressure ratio the operating range naturally reduces and techniques to extend the range are necessary. The inducer bleed slot is a technique which has been adopted in turbocharger compressors. This approach was first reported by Fisher (1988) and was described as a Map Width Enhancement slot (MWE). The flow conditions in the MWE slot and impeller inlet duct were investigated with a view to developing an improved understanding of the flow mechanisms involved as the flow rate was reduced from choice to surge. Mean temperature and pressure measurements were recorded in the MWE passage, the main inducer duct to the impeller and the inlet duct upstream of the compressor. In addition the development of flow pulsations were monitored with pressure transducers in the MWE passage, the main inducer duct and the inlet duct, together with the application of flow visualisation techniques. The transient pressure measurements showed that low frequency flow pulsations developed in the MWE passage at high flow rates. As the flow rate was reduced the low frequency pulsations disappeared and flow reversal through the MWE passage developed. It was shown that flow reversal through the MWE passage commenced at flow rates close to the peak efficiency point for the compressor.

Unsteady Pressure Characteristics in the Mainstream/Disc Cavity of a Turbine-Stage

2017 ◽  
Author(s):  
A. V. Mirzamoghadam ◽  
J. Balasubramanian ◽  
M. Michael ◽  
R. P. Roy
Keyword(s):  
Flow Rate ◽  
Static Pressure ◽  
Cfd Simulation ◽  
Air Flow ◽  
Fast Response ◽  
Pressure Measurements ◽  
Turbine Stage ◽  
Unsteady Pressure ◽  
Purge Flow ◽  
The Difference

The interaction between the mainstream and disc cavity purge flows in a turbine stage is an unsteady 360° phenomenon. Most of the current rotating rigs have used steady pressure transducers to measure the mainstream annulus pressure distributions as well as the pressure distribution in the disc cavity. Unsteady static pressure measurements in these regions using fast-response transducers have also been reported but to a much lesser degree, mainly at ASU, OSU, VKI, and ETH. To gain better insight into the prevailing unsteady flow phenomena, and to assess the difference between steady and time-averaged unsteady pressure data, new unsteady static pressure measurements were recently carried out at three locations in an ASU-Honeywell turbine stage, namely, in the main gas path on the outer shroud near vane trailing edge as well as on the vane platform lip, and on the stator surface rim seal. They are reported in this paper along with the comparative results of the corresponding URANS CFD simulation reported in an earlier publication. Experiments were carried out at five different purge air flow conditions for each of the two mainstream air flow rate and rotor speed combinations. The current unsteady measurements indicate that the rim cavity pressure frequency is governed by the blade passage frequency. The unsteadiness amplitude increases with purge flow in the main gas path, but decreases with increase in purge flow for the rim cavity where the sensitivity to change in purge flow is smaller at the lower mainstream flow rate. The difference in the ambient-corrected time-averaged static pressures between those evaluated from the current unsteady measurements and the previously published steady measurements are found to be within the measurement uncertainties.

scholarly journals An Experimental Study of the Flow Field Inside the Diffuser Passage of a Laboratory Centrifugal Pump

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Qiaorui Si ◽  
Patrick Dupont ◽  
Annie-Claude Bayeul-Lainé ◽  
Antoine Dazin ◽  
Olivier Roussette ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Design Flow ◽  
Low Flow ◽  
Mean Flow ◽  
Local Pressure ◽  
Flow Rates ◽  
Piv Measurement ◽  
Measurement Results

Measurements are processed on a centrifugal pump model, which works with air and performs with the vane-island type diffuser of a real hydraulic pump, under five flow rates to investigate the internal flow characteristics and their influence on overall pump performance. The mean flow characteristics inside the diffuser are determined by using a miniature three-hole probe connected to an online data acquisition system. The flow structure at the inlet section of the diffuser is analyzed in detail, with a focus on the local pressure loss inside the vaneless gap and incidence angle distributions along the hub-to-shroud direction of the diffuser. Some existing calculations, including leakage effects, are used to evaluate the pressure recovery downstream of the impeller. Furthermore, particle image velocimetry (PIV) measurement results are obtained to help analyze the flow characteristics inside the vane-island diffuser. Each PIV measuring plane is related to one particular diffuser blade-to-blade channel and is analyzed by using the time-averaged method according to seven different relative positions of the impeller. Measurement results show that main loss is produced inside the vaneless part of the diffuser at low flow rates, which might have been caused by the strong rotor–stator interaction. When the impeller flow rate is greater than the diffuser design flow rate, a large fluctuating separated region occurs after the throat of the diffuser on the pressure side. Mean loss originates from the unsteady pressure downstream of the diffuser throat. For better characterization of the separations observed in previous experimental studies, complementary unsteady static pressure measurement campaigns have been conducted on the diffuser blade wall. The unsteadiness revealed by these measurements, as well as theirs effects on the diffuser performance, was then studied.

Sign in / Sign up

Export Citation Format

Share Document