The Effect of a Large Hole on the Stress Concentration Factor of a Satellite Hole in a Tension Field

1999 ◽  
Vol 121 (3) ◽  
pp. 252-256 ◽  
Author(s):  
C. S. Sloan ◽  
M. D. Cowell ◽  
T. F. Lehnhoff
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Concentration Factor ◽  
Concentration Factor ◽  
Hole Diameter ◽  
Element Analysis ◽  
Large Hole ◽  
Concentration Factors ◽  
Stress Concentration Factors

Stress concentration factors have been determined for large hole to small hole diameter ratios (D/d) of 10 to 50 for two holes in an infinitely wide tension-loaded panel. Finite element analysis was used to model the system of two holes in a plate that approximates the infinitely wide and tall case. Both the D/d ratio and edge to edge hole spacing were examined for hole placement along an axis perpendicular to the direction of the tension field. It was found for large D/d ratios that the stress concentration factor was only dependent on the distance between the hole edges divided by the large hole diameter. For the configurations analyzed, the stress concentration factors varied from approximately 3 to 11.

Numerical Investigation of Stress Concentration Factor at Irregular Corrosion Pit Under Tension-Torsion Loading

2014 ◽  
Author(s):  
Yuhui Huang ◽  
Chengcheng Wang ◽  
Shan-Tung Tu ◽  
Fu-Zhen Xuan ◽  
Takamoto Itoh
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Aspect Ratio ◽  
Stress Concentration Factor ◽  
Concentration Factor ◽  
Three Dimensional ◽  
Element Analysis ◽  
Stress Concentration Factors ◽  
Local Dissolution

Finite element analysis is adopted to study the stress concentration of pit area under tension-torsion loading. The stress concentration factors under regular evolution and irregular evolution of pits are investigated by conducting a series of three-dimensional semi-elliptical pitted models. Based on the finite element analysis, it can be concluded that pit aspect ratio (a/2c) is a significant parameter affecting stress concentration factor (SCF) for regular evolution pits. Pits, having higher aspect ratio, are very dangerous form and can cause significant reduction in the load carrying capacity. When local dissolution occurs in the pitting area, SCF will have a sharp increase, it is more probable for a crack to initiate from these areas compared with pits for regular evolution. Furthermore, local dissolution coefficient is proposed to study effect of local dissolution within the pit on SCF.

An Estimation Formula of the Stress Concentration Factor of the Butt-Welded Joint

2007 ◽  
Vol 353-358 ◽  
pp. 1995-1998
Author(s):  
Byeong Choon Goo
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Gas Metal Arc Welding ◽  
Element Analysis ◽  
Butt Weld ◽  
Estimation Formula ◽  
Metal Arc Welding ◽  
Concentration Factors ◽  
Stress Concentration Factors

The purpose of this paper is to develop an estimation formula of stress concentration factors of butt-welded components under tensile loading. To investigate the influence of weld bead profiles on stress concentration factors of double V groove butt-welded joints, butt-welded specimens were made by CO2 gas metal arc welding. And the three main parameters, the toe radius, flank angle and bead height were measured by a profile measuring equipment. By using the measured data, the influence of three parameters on the stress concentration factors was investigated by a finite element analysis. It is shown that the three parameters have similar effects on the stress concentration factors. According to the simulation results, a formula to estimate the stress concentration factors of butt-weld welded structures was proposed and the estimated concentration factors from the formula were compared with the results obtained by the finite element analysis. The two results are in a good agreement.

An Assessment of Structural Details in Lightweight Marine Structures

2004 ◽  
Author(s):  
Carlos A. Pereira ◽  
Paulo P. Silva ◽  
Anto´nio F. Mateus ◽  
Joel A. Witz
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Failure Modes ◽  
Marine Structures ◽  
Element Analysis ◽  
Linear Finite Element ◽  
Structural Details ◽  
Concentration Factors ◽  
Stress Concentration Factors

This paper presents the results of investigations into the mechanics and failure modes of structural details usually encountered in lightweight marine structures. The structural analyses are performed using non-linear finite element analysis. The stress concentration factors and expected fatigue lives of the as designed and the as built structural details are evaluated and alternative configurations are discussed with the aim of improving the designs for production.

scholarly journals DETERMINATION OF STRESS CONCENTRATION FACTORS OF A STEAM TURBINE ROTOR USING FINITE ELEMENT ANALYSIS

1970 ◽  
Vol 40 (2) ◽  
pp. 137-141
Author(s):  
R. Nagendra Babu ◽  
K. V. Ramana ◽  
K. Mallikarjuna Rao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Steam Turbine ◽  
Turbine Rotor ◽  
Element Analysis ◽  
Steam Turbine Rotor ◽  
Fine Mesh ◽  
Concentration Factors ◽  
Stress Concentration Factors

Stress Concentration Factors are significant in machine design as it gives rise to localized stress when any change in the design of surface or abrupt change in the cross section occurs. Almost all machine components and structural members contain some form of geometrical or microstructural discontinuities. These discontinuities are very dangerous and lead to failure. So, it is very much essential to analyze the stress concentration factors for critical applications like Turbine Rotors. In this paper Finite Element Analysis (FEA) with extremely fine mesh in the vicinity of the blades of Steam Turbine Rotor is applied to determine stress concentration factors.Keywords: Stress Concentration Factors; FiniteElement Analysis; ANSYS.DOI: 10.3329/jme.v40i2.5355Journal of Mechanical Engineering, Vol. ME 40, No. 2, December 2009 137-141

Finite Element Analysis on Stress Concentration of Well Casing With Corrosion Pits

2010 ◽  
Author(s):  
Jing Zhang ◽  
Jianchun Fan ◽  
Laibin Zhang ◽  
Dong Wen ◽  
Yumei Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Concentration Factor ◽  
Concentration Factor ◽  
Spherical Cavity ◽  
High Stress ◽  
Orifice Diameter ◽  
Element Analysis ◽  
Corrosion Pits

Corrosion-induced pits will disturb the original stress distribution of casing and appear local high stress area. Through 3-D finite element analysis on casing with spherical and cylindrical corrosion cavity, the stress concentration degree and the influences of cavity shape, size and orifice diameter on stress concentration factor are determined and analyzed. The results show that the depth and shape of corrosion cavities are major factors impacting the stress concentration factor. For the casing with corrosion pits, the smaller orifice diameter, the more obvious influence of hemisphere effect on stress concentration factor. With the transition from shallow-spherical cavity to exact hemispherical cavity or from exact hemispherical cavity to deep-spherical cavity or from exact hemispherical cavity to cylindrical cavity, the changes of stress concentration factor show different characteristics.

Engineering Procedure for Calculation of Elastic Stress Concentration Factors of Bearing Pad Fretting Flaws

2009 ◽  
Author(s):  
Bogdan S. Wasiluk ◽  
Douglas A. Scarth
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Crack Initiation ◽  
Stress Concentration Factor ◽  
Concentration Factor ◽  
Elastic Stress ◽  
Elliptical Hole ◽  
Flat Bottom ◽  
Concentration Factors ◽  
Stress Concentration Factors

Procedures to evaluate volumetric bearing pad fretting flaws for crack initiation are in the Canadian Standard N285.8 for in-service evaluation of CANDU® pressure tubes. The crack initiation evaluation procedures use equations for calculating the elastic stress concentration factors. Newly developed engineering procedure for calculation of the elastic stress concentration factor for bearing pad fretting flaws is presented. The procedure is based on adapting a theoretical equation for the elastic stress concentration factor for an elliptical hole to the geometry of a bearing pad fretting flaw, and fitting the equation to the results from elastic finite element stress analyses. Non-dimensional flaw parameters a/w, a/c and a/ρ were used to characterize the elastic stress concentration factor, where w is wall thickness of a pressure tube, a is depth, c is half axial length, and ρ is root radius of the bearing pad fretting flaw. The engineering equations for 3-D round and flat bottom bearing pad fretting flaws were examined by calculation of the elastic stress concentration factor for each case in the matrix of source finite element cases. For the round bottom bearing pad fretting flaw, the fitted equation for the elastic stress concentration factor agrees with the finite element results within ±3.7% over the valid range of flaw geometries. For the flat bottom bearing pad fretting flaw, the fitted equation agrees with the finite element results within ±4.0% over the valid range of flaw geometries. The equations for the elastic stress concentration factor have been verified over the valid range of flaw geometries to ensure accurate results with no anomalous behavior. This included comparison against results from independent finite element calculations.

Sign in / Sign up

Export Citation Format

Share Document