On the Design Criteria for Suppression of Secondary Flows in Centrifugal and Mixed Flow Impellers

1998 ◽  
Vol 120 (4) ◽  
pp. 723-735 ◽  
Author(s):  
M. Zangeneh ◽  
A. Goto ◽  
H. Harada
Keyword(s):  
Flow Field ◽  
Pressure Distribution ◽  
Centrifugal Compressor ◽  
Design Method ◽  
Three Dimensional ◽  
Design Guidelines ◽  
Secondary Flows ◽  
Mixed Flow ◽  
Optimum Pressure ◽  
Specific Speed

In this paper, for the first time, a set of guidelines is presented for the systematic design of mixed flow and centrifugal compressors and pumps with suppressed secondary flows and a uniform exit flow field. The paper describes the shape of the optimum pressure distribution for the suppression of secondary flows in the impeller with reference to classical secondary flow theory. The feasibility of achieving this pressure distribution is then demonstrated by deriving guidelines for the design specifications of a three-dimensional inverse design method, in which the blades are designed subject to a specified circulation distribution or 2πrVθ. The guidelines will define the optimum choice of the blade loading or ∂rVθ/∂m and the stacking condition for the blades. These guidelines are then used in the design of three different low specific speed centrifugal pump impellers and a high specific speed industrial centrifugal compressor impellers. The flows through all the designed impellers are computed numerically by a three-dimensional viscous code and the resulting flow field is compared to that obtained in the corresponding conventional impeller. The results show consistent suppression of secondary flows in all cases. The design guidelines are validated experimentally by comparing the performance of the inverse designed centrifugal compressor impeller with the corresponding conventional impeller. The overall performance of the stage with the inverse designed impeller with suppressed secondary flows was found to be 5 percent higher than the conventional impeller at the peak efficiency point. Exit flow traverse results at the impeller exit indicate a more uniform exit flow than that measured at the exit from the conventional impeller.

On the Design Criteria for Suppression of Secondary Flows in Centrifugal and Mixed Flow Impellers

1997 ◽  
Author(s):  
M. Zangeneh ◽  
A. Goto ◽  
H. Harada
Keyword(s):  
Flow Field ◽  
Pressure Distribution ◽  
Centrifugal Compressor ◽  
Design Method ◽  
Secondary Flows ◽  
Mixed Flow ◽  
Optimum Pressure ◽  
Compressor Impeller ◽  
Specific Speed ◽  
Guide Lines

In this paper, for the first lime, a set of guide-lines are presented for the systematic design of mixed flow and centrifugal compressors and pumps with suppressed secondary flows and a uniform exit flow field. The paper describes the shape of the optimum pressure distribution for the suppression of secondary flows in the impeller with reference to classical secondary flow theory. The feasibility of achieving this pressure distribution is then demonstrated by deriving guide-lines for the design specifications of a 3D inverse design method, in which the blades are designed subject to a specified circulation distribution or 2πrV¯θ. The guide-lines will define the optimum choice of the blade loading or ∂rV¯θ/∂m and the stacking condition for the blades. These guide-lines are then used in the design of three different low specific speed centrifugal pump impellers and a high specific speed industrial centrifugal compressor impeller. The flow through all the designed impellers are computed numerically by a 3D viscous code and the resulting flow field is compared to that obtained in the corresponding conventional impeller. The results show consistent suppression of secondary flows in all cases. The design guide-lines are validated experimentally by comparing the performance of the inverse designed centrifugal compressor impeller with the corresponding conventional impeller. The overall performance of the stage with the inverse designed impeller with suppressed secondary flows was found to be 5% higher than the conventional impeller at the peak efficiency point. Exit flow traverse results at the impeller exit indicate a more uniform exit flow than that measured at the exit from the conventional impeller.

On the role of three-dimensional inverse design methods in turbomachinery shape optimization

1999 ◽  
Vol 213 (1) ◽  
pp. 27-42 ◽  
Author(s):  
M Zangeneh ◽  
A Goto ◽  
H Harada
Keyword(s):  
Flow Field ◽  
Inverse Method ◽  
Design Method ◽  
Three Dimensional ◽  
Design Guidelines ◽  
Secondary Flows ◽  
Inverse Design ◽  
Vaned Diffuser ◽  
Oil Flow ◽  
Inverse Design Method

The application of a three-dimensional (3D) inverse design method in which the blade geometry is computed for a specified distribution of circulation to the design of turbomachinery blades is explored by using two examples. In the first instance the method is applied to the design of radial and mixed flow impellers to suppress secondary flows. Based on our understanding of the fluid dynamics of the flow in the impeller, simple guidelines are developed for input specification of the inverse method in order to systematically design impellers with suppressed secondary flows and a more uniform exit flow field. In the second example the method is applied to the design of a vaned diffuser. Again based on the understanding of the detailed flow field in the diffuser obtained by using 3D viscous calculations and oil flow visualizations, simple design guidelines are developed for input specification to the inverse method in order to suppress corner separation. In both cases the guidelines are verified numerically and in the case of the diffuser further experimental validation is presented.

Suppression of Secondary Flows in a Mixed-Flow Pump Impeller by Application of Three-Dimensional Inverse Design Method: Part 1—Design and Numerical Validation

1996 ◽  
Vol 118 (3) ◽  
pp. 536-543 ◽  
Author(s):  
M. Zangeneh ◽  
A. Goto ◽  
T. Takemura
Keyword(s):  
Flow Field ◽  
Design Method ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Inverse Design ◽  
Suction Surface ◽  
Mixed Flow ◽  
Pump Impeller ◽  
Inverse Design Method ◽  
Flow Pump

This paper describes the design of the blade geometry of a medium specific speed mixed flow pump impeller by using a three-dimensional inverse design method in which the blade circulation (or rVθ) is specified. The design objective is the reduction of impeller exit flow nonuniformity by reducing the secondary flows on the blade suction surface. The paper describes in detail the aerodynamic criteria used for the suppression of secondary flows with reference to the loading distribution and blade stacking condition used in the design. The flow through the designed impeller is computed by Dawes’ viscous code, which indicates that the secondary flows are well suppressed on the suction surface. Comparison between the predicted exit flow field of the inverse designed impeller and a corresponding conventional impeller indicates that the suppression of secondary flows has resulted in substantial improvement in the exit flow field. Experimental comparison of the flow fields inside and at exit from the conventional and the inverse designed impeller is made in Part 2 of the paper.

Unsteady Flow at the Outlet of the High Specific Speed Centrifugal Compressor Impeller

1984 ◽  
Author(s):  
Fumikata Kano ◽  
Takafumi Shirakami
Keyword(s):  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Coal Gasification ◽  
Three Dimensional ◽  
Axial Direction ◽  
Navier Stokes ◽  
Meridional Plane ◽  
Mixed Flow ◽  
Navier Stokes Equation ◽  
Specific Speed

The unsteady flow at the outlet of the high specific speed mixed flow Impeller was studied. The specific speed is 500 (m3/min)1/2 · rpm · m−3/4. The flow is strongly influenced by the impeller blading. The other hand, the flow influences the performance of the stationary vanes downstream of the impeller. The flow path at the outlet of the mixed flow impeller is inclined to the axial direction and is curved in the meridional plane. The study was carried out to develop the 30 MW centrifugal compressor. This compressor is used in the field of the coal gasification, the geothermal power generation, etc. The distributions of flow velocity, pressure and temperature of three dimensional flow were measured using a high sensitive pressure transducer and a total temperature probe. The flow was surveyed across the entire passage at about ten axial locations including endwall boundary layer. A theoretical analysis was also carried out using the linearized Navier-Stokes equation.

Development and Industrial Application of the “All-Over-Controlled Vortex Distribution Method” for Designing Radial and Mixed Flow Impellers

1992 ◽  
Author(s):  
S. J. Wang ◽  
M. J. Yuan ◽  
G. Xi ◽  
S. X. Liu ◽  
D. T. Qi ◽  
...  
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Inverse Method ◽  
Three Dimensional ◽  
Industrial Applications ◽  
Mixed Flow ◽  
Distribution Method ◽  
Stream Surface ◽  
Surface Theory ◽  
Performance Curves

Sixteen years ago an inverse method of designing radial, mixed flow impellers was proposed by the first author of this paper, which was based on a quasi-three-dimensional stream surface theory. The contradictions between the full controlling of the flow field in the whole impeller and the designed bables’ smooth machinability can be perfectly resolved with the above method (So it is called “all-over-controlled vortex distribution method”). This paper presents the developments and industrial applications of the above method in the last decade. Two single centrifugal compressor model stages with the 3-D impellers designed by this method are studied in detail, and several performance curves of the multistage centrifugal compressors designed by this method are also presented.

Nonaxisymmetric Turbine End Wall Design: Part I— Three-Dimensional Linear Design System

1999 ◽  
Vol 122 (2) ◽  
pp. 278-285 ◽  
Author(s):  
Neil W. Harvey ◽  
Martin G. Rose ◽  
Mark D. Taylor ◽  
Shahrokh Shahpar ◽  
Jonathan Hartland ◽  
...  
Keyword(s):  
Flow Field ◽  
Design Method ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Design System ◽  
Linear Superposition ◽  
Turbine Rotor Blade ◽  
End Wall

A linear design system, already in use for the forward and inverse design of three-dimensional turbine aerofoils, has been extended for the design of their end walls. This paper shows how this method has been applied to the design of a nonaxisymmetric end wall for a turbine rotor blade in linear cascade. The calculations show that nonaxisymmetric end wall profiling is a powerful tool for reducing secondary flows, in particular the secondary kinetic energy and exit angle deviations. Simple end wall profiling is shown to be at least as beneficial aerodynamically as the now standard techniques of differentially skewing aerofoil sections up the span, and (compound) leaning of the aerofoil. A design is presented that combines a number of end wall features aimed at reducing secondary loss and flow deviation. The experimental study of this geometry, aimed at validating the design method, is the subject of the second part of this paper. The effects of end wall perturbations on the flow field are calculated using a three-dimensional pressure correction based Reynolds-averaged Navier–Stokes CFD code. These calculations are normally performed overnight on a cluster of work stations. The design system then calculates the relationships between perturbations in the end wall and resulting changes in the flow field. With these available, linear superposition theory is used to enable the designer to investigate quickly the effect on the flow field of many combinations of end wall shapes (a matter of minutes for each shape). [S0889-504X(00)00902-8]

Performance of a Mixed Flow Pump with Varying Tip Clearance: Part 1

1996 ◽  
Vol 210 (4) ◽  
pp. 305-318 ◽  
Author(s):  
T K Saha ◽  
S Soundranayagam
Keyword(s):  
Angular Momentum ◽  
Flow Field ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Flow Reversal ◽  
Tip Clearance ◽  
Mixed Flow ◽  
Three Dimensional Flow ◽  
Specific Speed ◽  
Flow Pump

Measurements of the three-dimensional flow field entering and leaving a mixed flow pump of non-dimensional specific speed k = 1.89 [ Ns = 100 r/min (metric)] are discussed as a function of flowrate. Flow reversal at inlet at reduced flows is seen to result in abnormally high total pressures in the casing region, but causes no noticeable discontinuities on the head-flow characteristics. Inlet prerotation is associated with the transport of angular momentum by the reversal eddy and begins with the initiation of flow reversal.

Inverse Design of Centrifugal Compressor Vaned Diffusers in Inlet Shear Flows

1996 ◽  
Vol 118 (2) ◽  
pp. 385-393 ◽  
Author(s):  
M. Zangeneh
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Design Method ◽  
Three Dimensional ◽  
Internal Flow ◽  
Inviscid Flow ◽  
Inverse Design ◽  
Flow Conditions ◽  
Inlet Flow ◽  
Blade Thickness

A three-dimensional inverse design method in which the blade (or vane) geometry is designed for specified distributions of circulation and blade thickness is applied to the design of centrifugal compressor vaned diffusers. Two generic diffusers are designed, one with uniform inlet flow (equivalent to a conventional design) and the other with a sheared inlet flow. The inlet shear flow effects are modeled in the design method by using the so-called “Secondary Flow Approximation” in which the Bernoulli surfaces are convected by the tangentially mean inviscid flow field. The difference between the vane geometry of the uniform inlet flow and nonuniform inlet flow diffusers is found to be most significant from 50 percent chord to the trailing edge region. The flows through both diffusers are computed by using Denton’s three-dimensional inviscid Euler solver and Dawes’ three-dimensional Navier–Stokes solver under sheared in-flow conditions. The predictions indicate improved pressure recovery and internal flow field for the diffuser designed for shear inlet flow conditions.

Design and Off-Design Numerical Investigation of a Transonic Double-Splitter Centrifugal Compressor

2008 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Cross Sections ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Complex Flow ◽  
Flow Measurements ◽  
Vaned Diffuser

The flow field of a high pressure ratio centrifugal compressor for turbocharger applications is investigated using a three-dimensional Navier-Stokes solver. The compressor is composed of a double-splitter impeller followed by a vaned diffuser. The flow field of the transonic open-shrouded impeller is highly three-dimensional, and it is influenced by shock waves, tip leakage vortices and secondary flows. Their interactions generate complex flow structures which are convected and distorted through the impeller blades. Both steady and unsteady computations are performed in order to understand the physical mechanisms which govern the impeller flow field while the operation ranges from choke to surge. Detailed Laser Doppler Velocimetry (LDV) flow measurements are available at various cross-sections inside the impeller blades at both design and off-design operating conditions.

Numerical Simulation of Internal Flow Field in Mixed Flow Fan

2013 ◽  
Vol 860-863 ◽  
pp. 1589-1593
Author(s):  
Yan Zhao Zhai ◽  
Hong Ming Zhang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Velocity Distribution ◽  
Pressure Distribution ◽  
Three Dimensional ◽  
Internal Flow ◽  
Field Structure ◽  
Mixed Flow ◽  
Flow Phenomenon ◽  
Impeller Outlet

The numerical simulation of internal flow field of a mixed-flow fan was carried out on the star-CD platform. Three-dimensional steady turbulent flow is calculated using the standard k-ɛ turbulence model, and the pressure distribution, velocity distribution and other important flow phenomenon inside the fan are obtained. The number of meshes has important influence on the result, meanwhile, fan inlet, impeller, outlet interact with each other. The results of numerical simulation can accurately analyze the fan flow field. The results of numerical simulation can accurately analyze the fan flow field structure, and provide guidance for further optimization and improvement of the fan.

Sign in / Sign up

Export Citation Format

Share Document