scholarly journals Oscillating Cascade Aerodynamics at Large Mean Incidence

1998 ◽  
Vol 120 (1) ◽  
pp. 122-130 ◽  
Author(s):  
D. H. Buffum ◽  
V. R. Capece ◽  
A. J. King ◽  
Y. M. EL-Aini
Keyword(s):  
Separation Bubble ◽  
Incidence Angle ◽  
Separated Flow ◽  
Leading Edge ◽  
Pressure Measurements ◽  
Suction Surface ◽  
Airfoil Surface ◽  
Attached Flow ◽  
Blade Tip ◽  
Fan Blade

The aerodynamics of a cascade of airfoils oscillating in torsion about the midchord is investigated experimentally at a large mean incidence angle and, for reference, at a low mean incidence angle. The airfoil section is representative of a modern, low-aspect-ratio, fan blade tip section. Time-dependent airfoil surface pressure measurements were made for reduced frequencies of up to 1.2 for out-of-phase oscillations at a Mach number of 0.5 and chordal incidence angles of 0 and 10 deg; the Reynolds number was 0.9 × 106. For the 10 deg chordal incidence angle, a separation bubble formed at the leading edge of the suction surface. The separated flow field was found to have a dramatic effect on the chordwise distribution of the unsteady pressure. In this region, substantial deviations from the attached flow data were found, with the deviations becoming less apparent in the aft region of the airfoil for all reduced frequencies. In particular, near the leading edge the separated flow had a strong destabilizing influence while the attached flow had a strong stabilizing influence.

scholarly journals Oscillating Cascade Aerodynamics at Large Mean Incidence

1996 ◽  
Author(s):  
Daniel H. Buffum ◽  
Vincent R. Capece ◽  
Aaron J. King ◽  
Yehia M. El-Aini
Keyword(s):  
Separation Bubble ◽  
Incidence Angle ◽  
Separated Flow ◽  
Leading Edge ◽  
Pressure Measurements ◽  
Suction Surface ◽  
Airfoil Surface ◽  
Attached Flow ◽  
Blade Tip ◽  
Fan Blade

The aerodynamics of a cascade of airfoils oscillating in torsion about the midchord is investigated experimentally at a large mean incidence angle and, for reference, at a low mean incidence angle. The airfoil section is representative of a modern, low aspect ratio, fan blade tip section. Time-dependent airfoil surface pressure measurements were made for reduced frequencies of up to 1.2 for out-of-phase oscillations at a Mach number of 0.5 and chordal incidence angles of 0° and 10°; the Reynolds number was 0.9×106. For the 10° chordal incidence angle, a separation bubble formed at the leading edge of the suction surface. The separated flow field was found to have a dramatic effect on the chordwise distribution of the unsteady pressure. In this region, substantial deviations from the attached flow data were found with the deviations becoming less apparent in the aft region of the airfoil for all reduced frequencies. In particular, near the leading edge the separated flow had a strong destabilizing influence while the attached flow had a strong stabilizing influence.

Predicting Transitional Separation Bubbles

2004 ◽  
Vol 127 (3) ◽  
pp. 497-501
Author(s):  
John A. Redford ◽  
Mark W. Johnson
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Transition Process ◽  
Test Cases ◽  
Transition Model ◽  
Flow Transition ◽  
Free Stream Turbulence ◽  
Attached Flow

This paper describes the modifications made to a successful attached flow transition model to produce a model capable of predicting both attached and separated flow transition. This transition model is used in combination with the Fluent CFD software, which is used to compute the flow around the blade assuming that it remains entirely laminar. The transition model then determines the start of transition location and the development of the intermittency. These intermittency values weight the laminar and turbulent boundary layer profiles to obtain the resulting transitional boundary layer parameters. The ERCOFTAC T3L test cases are used to validate the predictions. The T3L blade is a flat plate with a semi-circular leading edge, which results in the formation of a separation bubble the length of which is strongly dependent on the transition process. Predictions were performed for five T3L test cases for differing free-stream turbulence levels and Reynolds numbers. For the majority of these test cases the measurements were accurately predicted.

Predicting Transitional Separation Bubbles

2004 ◽  
Author(s):  
John A. Redford ◽  
Mark W. Johnson
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Transition Process ◽  
Reynolds Numbers ◽  
Test Cases ◽  
Transition Model ◽  
Flow Transition ◽  
Attached Flow

This paper describes the modifications made to a successful attached flow transition model to produce a model capable of predicting both attached and separated flow transition. This transition model is used in combination with the Fluent CFD software, which is used to compute the flow around the blade assuming that it remains entirely laminar. The transition model then determines the start of transition location and the development of the intermittency. These intermittency values weight the laminar and turbulent boundary layer profiles to obtain the resulting transitional boundary layer parameters. The ERCOFTAC T3L test cases are used to validate the predictions. The T3L blade is a flat plate with a semi-circular leading edge, which results in the formation of a separation bubble the length of which is strongly dependent on the transition process. Predictions were performed for five T3L test cases for differing freestream turbulence levels and Reynolds numbers. For the majority of these test cases the measurements were accurately predicted.

scholarly journals Periodicity and Repetivity of Unsteady Measurements of an Annular Turbine Cascade at Off Design Flow Conditions

1993 ◽  
Author(s):  
A. Bölcs ◽  
H. Körbächer
Keyword(s):  
Steady State ◽  
Test Data ◽  
Separation Bubble ◽  
Incidence Angle ◽  
Leading Edge ◽  
Design Flow ◽  
Turbine Cascade ◽  
Flow Conditions ◽  
Suction Surface ◽  
Shock Region

A two-dimensional section of a gas turbine cascade has been investigated experimentally in an annular non-rotating cascade facility as regards to its steady-state and time-dependent aerodynamic characteristics at off-design flow conditions. The blades vibrated in the first traveling wave bending mode. Steady-state and unsteady data were obtained for an off-design incidence angle of about 22° and for an isentropic outlet Mach number of M2s=1.19. At this flow condition, a separation bubble was present on the suction surface close to the leading edge. A shock appeared at trans- and supersonic outlet flow conditions on the suction surface. The data showed high unsteady loads close to the leading edge and in the shock region. It was found that the steady and the unsteady pressures in the shock region on the blade surface seemed to be very sensitive to small changes in the flow conditions. The periodicity and repetitivity of the steady and the unsteady pressures (σ=180°) was checked at several circumferential channel positions. This was done to figure out to which extend test data obtained in an annular ring channel can serve as a basis for the comparison with numerically obtained data. The aim of this paper is to show where problems may arise when comparing calculated results with test data.

The Measurement of Boundary Layers on a Compressor Blade in Cascade: Part 2—Suction Surface Boundary Layers

1988 ◽  
Vol 110 (1) ◽  
pp. 138-145 ◽  
Author(s):  
S. Deutsch ◽  
W. C. Zierke
Keyword(s):  
Boundary Layers ◽  
Separation Bubble ◽  
Incidence Angle ◽  
Outer Region ◽  
Leading Edge ◽  
Compressor Blade ◽  
Surface Boundary ◽  
Suction Surface ◽  
Circular Arc ◽  
Edge Separation

Using the facility described in Part 1 [29], eleven detailed velocity and turbulence intensity profiles are obtained on the suction surface of a double circular arc blade in cascade. At the measured incidence angle of 5 deg, transition through a leading edge separation bubble occurs before 2.6 percent chord. A continuing recovery from this leading edge separation is apparent in the measured boundary layer profiles at 2.6 and 7.6 percent chord. Recovery appears to be complete by 12.7 percent chord. The data then illustrate the evolution of the nonequilibrium turbulent boundary layers as they approach a second region of separation. Following the criteria established by Simpson et al. [1], we find that intermittent separation occurs near 60 percent chord while detachment occurs at 84.2 percent chord. Comparison between the measured profiles and the sublimation visualization studies indicates that the flow visualization is signaling the location of incipient detachment (1 percent instantaneous backflow). Measured profiles are also considered in light of similarity techniques for boundary layers approaching separation. Outer region similarity is shown to vanish for profiles downstream of detachment.

Characteristics of a separated flow past a semicircular leading-edge airfoil model under different imposed pressure gradient

2021 ◽  
pp. 095441002110212
Author(s):  
K Anand ◽  
KT Ganesh
Keyword(s):  
Boundary Layer ◽  
Particle Image Velocimetry ◽  
Pressure Gradient ◽  
Particle Image ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Field Measurements ◽  
Bench Mark ◽  
Image Velocimetry

The effect of pressure gradient on a separated boundary layer past the leading edge of an airfoil model is studied experimentally using electronically scanned pressure (ESP) and particle image velocimetry (PIV) for a Reynolds number ( Re) of 25,000, based on leading-edge diameter ( D). The features of the boundary layer in the region of separation and its development past the reattachment location are examined for three cases of β (−30°, 0°, and +30°). The bubble parameters such as the onset of separation and transition and the reattachment location are identified from the averaged data obtained from pressure and velocity measurements. Surface pressure measurements obtained from ESP show a surge in wall static pressure for β = −30° (flap deflected up), while it goes down for β = +30° (flap deflected down) compared to the fundamental case, β = 0°. Particle image velocimetry results show that the roll up of the shear layer past the onset of separation is early for β = +30°, owing to higher amplification of background disturbances compared to β = 0° and −30°. Downstream to transition location, the instantaneous field measurements reveal a stretched, disoriented, and at instances bigger vortices for β = +30°, whereas a regular, periodically shed vortices, keeping their identity past the reattachment location, is observed for β = 0° and −30°. Above all, this study presents a new insight on the features of a separation bubble receiving a disturbance from the downstream end of the model, and these results may serve as a bench mark for future studies over an airfoil under similar environment.

Large Eddy Simulation of Wake-Shear Layer Interactions Over a Multi-Element Aerofoil

2020 ◽  
Author(s):  
Souvik Naskar ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Modern commercial airliners use multi-element aerofoils to enhance take-off and landing performance. Further, multielement aerofoil configurations have been shown to improve the aerodynamic characteristics of wind turbines. In the present study, high resolution Large Eddy Simulation (LES) is used to explore the low Reynolds Number (Re = 0.832 × 104) aerodynamics of a 30P30N multi-element aerofoil at an angle of attack, α = 4°. In the present simulation, wake shed from a leading edge element or slat is found to interact with the separated shear layer developing over the suction surface of the main wing. High receptivity of shear layer via amplification of free-stream turbulence leads to rollup and breakdown, forming a large separation bubble. A transient growth of fluctuations is observed in the first half of the separation bubble, where levels of turbulence becomes maximum near the reattachment and then decay depicting saturation of turbulence. Results of the present LES are found to be in close agreement with the experiment depicting high vortical activity in the outer layer. Some features of the flow field here are similar to those occur due to interactions of passing wake and the separated boundary layer on the suction surface of high lift low pressure turbine blades.

Numerical Investigation of the Effect of Inlet Flow Angle on Film Cooling Performance for the Blade Tip With Suction Surface Squealer Rim

2019 ◽  
Author(s):  
Zhiqiang Yu ◽  
Jianjun Liu ◽  
Chen Li ◽  
Baitao An
Keyword(s):  
Mass Flow ◽  
Film Cooling ◽  
Incidence Angle ◽  
Leading Edge ◽  
Flow Ratio ◽  
Suction Surface ◽  
Cooling Performance ◽  
Tip Leakage ◽  
Pressure Surface ◽  
Mass Flow Ratio

Abstract Numerical investigations have been performed to study the effect of incidence angle on the aerodynamic and film cooling performance for the suction surface squealer tip with different film-hole arrangements at τ = 1.5% and BR = 1.0. Meanwhile, the full squealer tip as baseline is also investigated. Three incidence angles at design condition (0 deg) and off-design conditions (± 7 deg) are investigated. The suction surface, pressure surface, and the camber line have seven holes each, with an extra hole right at the leading edge. The Mach number at the cascade inlet and outlet are 0.24 and 0.52, respectively. The results show that the incidence angle has a significant effect on the tip leakage flow characteristics and coolant flow direction. The film cooling effectiveness distribution is altered, especially for the film holes near the leading edge. When the incidence angle changes from +7 deg to 0 and −7 deg, the ‘re-attachment line’ moves downstream and the total tip leakage mass flow ratio decreases, but the suction surface tip leakage mass flow ratio near leading edge increases. In general, the total tip leakage mass flow ratio for suction surface squealer tip is 1% greater than that for full squealer tip at the same incidence angle. The total pressure loss coefficient of suction surface squealer tip is larger than that for full squealer tip. The full squealer tip with film holes near suction surface and the suction surface squealer tip with film hole along camber line show high film cooling performance, and the area averaged film cooling effectiveness at positive incidence angle +7 deg is higher than that at 0 and −7 deg. The coolant discharged from film holes near pressure surface only cools narrow region near pressure surface.

scholarly journals Turbulence Amplification with Incidence at the Leading Edge of a Compressor Cascade

1999 ◽  
Vol 5 (2) ◽  
pp. 89-98 ◽  
Author(s):  
Garth V. Hobson ◽  
Bryce E. Wakefield ◽  
William B. Roberts
Keyword(s):  
Separation Bubble ◽  
Leading Edge ◽  
Laser Doppler Velocimeter ◽  
Free Shear Layer ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Flow Angle ◽  
Laminar Separation ◽  
High Incidence ◽  
High Turbulence

Detailed measurements, with a two-component laser-Doppler velocimeter and a thermal anemometer were made near the suction surface leading edge of controlled-diffusion airfoils in cascade. The Reynolds number was near 700,000, Mach number equal to 0.25, and freestream turbulence was at 1.5% ahead of the cascade.It was found that there was a localized region of high turbulence near the suction surface leading edge at high incidence. This turbulence amplification is thought to be due to the interaction of the free-shear layer with the freestream inlet turbulence. The presence of the local high turbulence affects the development of the short laminar separation bubble that forms very near the suction side leading edge of these blades. Calculations indicate that the local high levels of turbulence can cause rapid transition in the laminar bubble allowing it to reattach as a short “non-burst” type.The high turbulence, which can reach point values greater than 25% at high incidence, is the reason that leading edge laminar separation bubbles can reattach in the high pressure gradient regions near the leading edge. Two variations for inlet turbulence intensity were measured for this cascade. The first is the variation ofmaximum inlet turbulence with respect to inlet-flow angle; and the second is the variation of leading edge turbulence with respect to upstream distance from the leading edge of the blades.

Separated Flow Measurements on a Highly Loaded Low-Pressure Turbine Airfoil

2008 ◽  
Author(s):  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Transition To Turbulence ◽  
Suction Surface ◽  
Airfoil Surface ◽  
Flow Measurements ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied on a new, very high lift, low-pressure turbine airfoil. Experiments were done under low freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Velocity profiles were acquired in the suction side boundary layer at several streamwise locations using hot-wire anemometry. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) ranging from 25,000 to 330,000. In all cases the boundary layer separated, but at high Reynolds number the separation bubble remained very thin and quickly reattached after transition to turbulence. In the low Reynolds number cases, the boundary layer separated and did not reattach, even when transition occurred. This behavior contrasts with previous research on other airfoils, in which transition, if it occurred, always induced reattachment, regardless of Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document