An Approach for the Stress Analysis of Transversely Isotropic Biphasic Cartilage Under Impact Load

1998 ◽  
Vol 120 (5) ◽  
pp. 608-613 ◽  
Author(s):  
J. J. Garcia ◽  
N. J. Altiero ◽  
R. C. Haut
Keyword(s):  
Stress Analysis ◽  
Impact Load ◽  
Transversely Isotropic ◽  
Incompressible Material ◽  
Shear Stresses ◽  
Stress Distributions ◽  
Cartilage Surface ◽  
Compressive Stresses ◽  
Blunt Impact ◽  
Contact Models

Stress analysis of contact models for isotropic articular cartilage under impacting loads shows high shear stresses at the interface with the subchondral bone and normal compressive stresses near the surface of the cartilage. These stress distributions are not consistent, with lesions observed on the cartilage surface of rabbit patellae from blunt impact, for example, to the patello-femoral joint. The purpose of the present study was to analyze, using the elastic capabilities of a finite element code, the stress distribution in more morphologically realistic transversely isotropic biphasic contact models of cartilage. The elastic properties of an incompressible material, equivalent to those of the transversely isotropic biphasic material at time zero, were derived algebraically using stress-strain relations. Results of the stress analysis showed the highest shear stresses on the surface of the solid skeleton of the cartilage and tensile stresses in the zone of contact. These results can help explain the mechanisms responsible for surface injuries observed during blunt insult experiments.

Axisymmetric Stress Analysis and Strength Evaluation of Bonded Shrink Fitted Joints of Circular Pipes Subjected to Internal Pressure and Tensile Loads

2000 ◽  
Author(s):  
Masahide Katsuo ◽  
Toshiyuki Sawa ◽  
Masahiro Yoneno
Keyword(s):  
Internal Pressure ◽  
Stress Analysis ◽  
Joint Strength ◽  
Tensile Load ◽  
Theory Of Elasticity ◽  
Shear Stresses ◽  
Stress Distributions ◽  
Strength Evaluation ◽  
Circular Pipes ◽  
Hollow Cylinders

Abstract This study deals with the stress analysis and the strength evaluation of a bonded shrink fitted joint of circular pipes subjected to an internal pressure and a tensile load. In the analysis, two pipes and the adhesive are replaced with finite hollow cylinders, and the stress distributions in the joint are analyzed by using the axisymmetric theory of elasticity. From the numerical calculations, the following results are obtained: (1) Both the compressive and shear stresses at the interface between the adherend and the adhesive increase as Young’s modulus of the adherend increases. (2) The stress becomes singular at the edges of the interfaces. (3) The joint strength can be evaluated using the compressive and shear stresses near the edge of the interface. In the experiments, bonded shrink fitted joints consisting of dissimilar circular pipes were manufactured, and rupture tests of the joints were carried out by applying an internal pressure, and a tensile load to the joints. From the results, the joint strength of the bonded shrink fitted joint was found to be greater than that of the shrink fitted joint. Furthermore, the numerical results are in fairly good agreement with the experimental ones.

Interfacial Stresses for Bonded Rubber Blocks in Compression and Shear

1974 ◽  
Vol 41 (4) ◽  
pp. 855-859 ◽  
Author(s):  
A. N. Gent ◽  
R. L. Henry ◽  
M. L. Roxbury
Keyword(s):  
Circular Cross Section ◽  
Shear Stresses ◽  
Stress Distributions ◽  
Interfacial Stresses ◽  
Average Value ◽  
Compressive Stresses ◽  
Theoretical Predictions ◽  
Set Up ◽  
Rigid Surfaces ◽  
Cross Section Maximum

When a rubber block is compressed between two rigid surfaces, to which it is bonded, both compressive and shear stresses are set up at the interfaces. These interfacial stresses have been measured for small compressions of four relatively-thin, flat rubber blocks of square and circular cross section. Maximum compressive stresses, nearly twice the average value, were developed in the center of the bonded surfaces. Shear stresses were found to increase continuously from zero at the center to maximum values at the edges. No evidence was detected of a singularity at the edges. For all of the blocks examined, the observed stress distributions agreed satisfactorily with theoretical predictions based on incompressibility of the rubber and a simple superposition of two deformation states. Measurements were also made of the shear stress distribution associated with an overall shear displacement of the block.

Finite Element Analysis of Tire/Rim Interface Forces Under Braking and Cornering Loads

1992 ◽  
Vol 20 (2) ◽  
pp. 83-105 ◽  
Author(s):  
J. P. Jeusette ◽  
M. Theves
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Contact Pressure ◽  
Element Model ◽  
Shear Stresses ◽  
Detailed Knowledge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Plane Shear ◽  
Normal Contact

Abstract During vehicle braking and cornering, the tire's footprint region may see high normal contact pressures and in-plane shear stresses. The corresponding resultant forces and moments are transferred to the wheel. The optimal design of the tire bead area and the wheel requires a detailed knowledge of the contact pressure and shear stress distributions at the tire/rim interface. In this study, the forces and moments obtained from the simulation of a vehicle in stationary braking/cornering conditions are applied to a quasi-static braking/cornering tire finite element model. Detailed contact pressure and shear stress distributions at the tire/rim interface are computed for heavy braking and cornering maneuvers.

scholarly journals Ultrasonic Deicing Efficiency Prediction and Validation for a Flat Deicing System

2020 ◽  
Vol 10 (19) ◽  
pp. 6640
Author(s):  
Zhonghua Shi ◽  
Zhenhang Kang ◽  
Qiang Xie ◽  
Yuan Tian ◽  
Yueqing Zhao ◽  
...  
Keyword(s):  
Lead Zirconate Titanate ◽  
Cohesive Zone ◽  
Cohesive Zone Model ◽  
Lead Zirconate ◽  
Efficiency Factor ◽  
Zone Model ◽  
Shear Stresses ◽  
Stress Distributions ◽  
Total Energy Density ◽  
Average Shear

An effective deicing system is needed to be designed to conveniently remove ice from the surfaces of structures. In this paper, an ultrasonic deicing system for different configurations was estimated and verified based on finite element simulations. The research focused on deicing efficiency factor (DEF) discussions, prediction, and validations. Firstly, seven different configurations of Lead zirconate titanate (PZT) disk actuators with the same volume but different radius and thickness were adopted to conduct harmonic analysis. The effects of PZT shape on shear stresses and optimal frequencies were obtained. Simultaneously, the average shear stresses at the ice/substrate interface and total energy density needed for deicing were calculated. Then, a coefficient named deicing efficiency factor (DEF) was proposed to estimate deicing efficiency. Based on these results, the optimized configuration and deicing frequency are given. Furthermore, four different icing cases for the optimize configuration were studied to further verify the rationality of DEF. The effects of shear stress distributions on deicing efficiency were also analyzed. At same time, a cohesive zone model (CZM) was introduced to describe interface behavior of the plate and ice layer. Standard-explicit co-simulation was utilized to model the wave propagation and ice layer delamination process. Finally, the deicing experiments were carried out to validate the feasibility and correctness of the deicing system.

Finite Element Analysis of Poor Distal Contact of the Femoral Component of a Cementless Hip Endoprosthesis

1993 ◽  
Vol 207 (4) ◽  
pp. 255-261 ◽  
Author(s):  
M Taylor ◽  
E W Abel
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Influencing Factor ◽  
Three Dimensional ◽  
Stress Distributions ◽  
Element Analysis ◽  
Hip Endoprosthesis ◽  
Applied Loading ◽  
Femoral Geometry ◽  
Contact Models

The difficulty of achieving good distal contact between a cementless hip endoprosthesis and the femur is well established. This finite element study investigates the effect on the stress distribution within the femur due to varying lengths of distal gap. Three-dimensional anatomical models of two different sized femurs were generated, based upon computer tomograph scans of two cadaveric specimens. A further six models were derived from each original model, with distal gaps varying from 10 to 60 mm in length. The resulting stress distributions within these were compared to the uniform contact models. The extent to which femoral geometry was an influencing factor on the stress distribution within the bone was also studied. Lack of distal contact with the prosthesis was found not to affect the proximal stress distribution within the femur, for distal gap lengths of up to 60 mm. In the region of no distal contact, the stress within the femur was at normal physiological levels associated with the applied loading and boundary conditions. The femoral geometry was found to have little influence on the stress distribution within the cortical bone. Although localized variations were noted, both femurs exhibited the same general stress distribution pattern.

scholarly journals Fractographical Analysis and Biomechanical Considerations of a Tooth Restored With Intracanal Fiber Post: Report of the Fracture and Importance of the Fiber Arrangements

2016 ◽  
Vol 41 (5) ◽  
pp. E149-E158 ◽  
Author(s):  
VF Wandscher ◽  
CD Bergoli ◽  
IF Limberger ◽  
TP Cenci ◽  
P Baldissara ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Glass Fiber ◽  
Shear Stresses ◽  
Fiber Post ◽  
Element Analysis ◽  
Parallel Fibers ◽  
Tooth Structure ◽  
Anterior Teeth ◽  
Compressive Stresses

SUMMARY Objective: This article aims to present a fractographic analysis of an anterior tooth restored with a glass fiber post with parallel fiber arrangement, taking into account force vectors, finite element analysis, and scanning electron microscopy (SEM). Methods: A patient presented at the Faculty of Dentistry (Federal University of Santa Maria, Brazil) with an endodontically treated tooth (ETT), a lateral incisor that had a restorable fracture. The treatment was performed, and the fractured piece was analyzed using stereomicroscopy, SEM, and finite element analysis. Results: The absence of remaining coronal tooth structure might have been the main factor for the clinical failure. We observed different stresses actuating in an ETT restored with a fiber post as well as their relationship with the ultimate fracture. Tensile, compression, and shear stresses presented at different levels inside the restored tooth. Tensile and compressive stresses acted together and were at a maximum in the outer portions and a minimum in the inner portions. In contrast, shear stresses acted concomitantly with tensile and compressive stresses. Shear was higher in the inner portions (center of the post), and lower in the outer portions. This was confirmed by finite element analysis. The SEM analysis showed tensile and compression areas in the fiber post (exposed fibers=tensile areas=lingual surface; nonexposed fibers=compression areas=buccal surface) and shear areas inside the post (scallops and hackle lines). Stereomicroscopic analysis showed brown stains in the crown/root interface, indicating the presence of microleakage (tensile area=lingual surface). Conclusion: We concluded that glass fiber posts with parallel fibers (0°), when restoring anterior teeth, present a greater fracture potential by shear stress because parallel fibers are not mechanically resistant to support oblique occlusal loads. Factors such as the presence of remaining coronal tooth structure and occlusal stability assist in the biomechanical equilibrium of stresses that act upon anterior teeth.

Numerical modelling of the crack-pore interaction and damage evolution behaviour of rocklike materials with pre-existing cracks and pores

2020 ◽  
pp. 105678952098387
Author(s):  
PLP Wasantha ◽  
D Bing ◽  
SQ Yang ◽  
T Xu
Keyword(s):  
Principal Stress ◽  
Damage Evolution ◽  
Shear Failure ◽  
Mechanical Response ◽  
Distribution Patterns ◽  
Stress Distributions ◽  
Compressive Stresses ◽  
Major Principal Stress ◽  
The Right ◽  
Macroscopic Failure

The combined effect of pre-existing cracks and pores on the damage evolution behaviour and mechanical properties of rocklike materials under uniaxial compression was numerically studied. Simulations of cracks and pores alone showed that increasing crack length and pore diameter decrease uniaxial compressive strength (UCS) and elastic modulus. Subsequent simulations considered two types of combinations of pre-existing cracks and pores – two cracks either side of a centric pore, and two pores either side of a centric crack – and the distance between cracks and pores was changed. In the case of two cracks at either side of the pore, UCS increased only slightly when the distance between the cracks and pore was increased. This was attributed to the more profound effect of the presence of the pore on UCS, and was confirmed by the progressive crack development characteristics and the major principal stress distribution patterns, which showed that the cracks initiated from the tips of the two pre-existing cracks made little or no contribution to the ultimate macroscopic failure. In contrast, models with two pores at either side of a centric crack showed a marked dependency of UCS on the distance between the pores and the crack. Cracks propagating from pre-existing pores made a greater contribution to the ultimate macroscopic failure when the pores were close to the centric crack and the effect gradually diminished with increasing space between pre-existing pores and the centric crack. Major principal stress distributions showed an asymmetric mobilisation of compressive stresses at the right and left sides of the two pores, favouring macroscopic shear failure when they were close to the centric crack which had led to a lower UCS. Overall, this study presents some critical insights into crack-pore interaction behaviour and the resulting mechanical response of rocklike materials to assist with the design of rock structures.

Anisotropic Porochemoelectroelastic Solution for an Inclined Wellbore Drilled in Shale

2013 ◽  
Vol 80 (2) ◽  
Author(s):  
Minh H. Tran ◽  
Younane N. Abousleiman
Keyword(s):  
Porous Media ◽  
Fluid Pressure ◽  
Transversely Isotropic ◽  
Biological Tissues ◽  
Analytical Models ◽  
Combined Effects ◽  
Saturated Porous Media ◽  
Stress Distributions ◽  
Shale Formations ◽  
Electrically Charged

The porochemoelectroelastic analytical models have been used to describe the response of chemically active and electrically charged saturated porous media such as clay soils, shales, and biological tissues. However, existing studies have ignored the anisotropic nature commonly observed on these porous media. In this work, the anisotropic porochemoelectroelastic theory is presented. Then, the solution for an inclined wellbore drilled in transversely isotropic shale formations subjected to anisotropic far-field stresses with time-dependent down-hole fluid pressure and fluid activity is derived. Numerical examples illustrating the combined effects of porochemoelectroelastic behavior and anisotropy on wellbore responses are also included. The analysis shows that ignoring either the porochemoelectroelastic effects or the formation anisotropy leads to inaccurate prediction of the near-wellbore pore pressure and effective stress distributions. Finally, wellbore responses during a leak-off test conducted soon after drilling are analyzed to demonstrate the versatility of the solution in simulating complex down-hole conditions.

Wrinkling of a Fiber-Reinforced Membrane

2008 ◽  
Vol 76 (1) ◽  
Author(s):  
E. Shmoylova ◽  
A. Dorfmann
Keyword(s):  
Boundary Conditions ◽  
Energy Function ◽  
Mechanical Response ◽  
Transverse Isotropy ◽  
Base Material ◽  
Strain Energy Function ◽  
Transversely Isotropic ◽  
Incompressible Material ◽  
Fiber Reinforced ◽  
Relaxed Energy

In this paper we investigate the response of fiber-reinforced cylindrical membranes subject to axisymmetric deformations. The membrane is considered as an incompressible material, and the phenomenon of wrinkling is taken into account by means of the relaxed energy function. Two cases are considered: transversely isotropic membranes, characterized by one family of fibers oriented in one direction, and orthotropic membranes, characterized by two family of fibers oriented in orthogonal directions. The strain-energy function is considered as the sum of two terms: The first term is associated with the isotropic properties of the base material, and the second term is used to introduce transverse isotropy or orthotropy in the mechanical response. We determine the mechanical response of the membrane as a function of fiber orientations for given boundary conditions. The objective is to find possible fiber orientations that make the membrane as stiff as possible for the given boundary conditions. Specifically, it is shown that for transversely isotropic membranes a unique fiber orientation exists, which does not affect the mechanical response, i.e., the overall behavior is identical to a nonreinforced membrane.

Sign in / Sign up

Export Citation Format

Share Document