Conditions for Scuffing Failure of Ground and Superfinished Steel Disks at High Sliding Speeds Using a Gas Turbine Engine Oil

1995 ◽  
Vol 117 (3) ◽  
pp. 482-489 ◽  
Author(s):  
M. J. Patching ◽  
C. C. Kweh ◽  
H. P. Evans ◽  
R. W. Snidle
Keyword(s):  
Experimental Investigation ◽  
Gas Turbine ◽  
Surface Finish ◽  
Axial Direction ◽  
Gas Turbine Engine ◽  
Hardened Steel ◽  
Engine Oil ◽  
Turbine Engine ◽  
Involute Gears ◽  
Scuffing Failure

This paper describes the results of an experimental investigation to compare the scuffing performance of conventionally ground and superfinished hardened steel disks operating at sliding speeds of up to 26 m/s and lubricated with a gas turbine engine oil at a temperature of 100° C. The ground disks were finished in the axial direction to simulate the orientation of surface finish found on involute gears. Superfinishing was found to give a significant increase in the load at which scuffing occurred. Frictional traction was also measured in the experiments and was found to be significantly lower for the superfinished disks in the loading stages preceding scuffing failure.

Determination of Thermoacoustic Response in a Demonstrator Gas Turbine Engine

2000 ◽  
Author(s):  
C. A. Arana ◽  
B. Sekar ◽  
M. A. Mawid
Keyword(s):  
Experimental Investigation ◽  
Gas Turbine ◽  
Analytical Model ◽  
Pressure Fluctuations ◽  
Gas Turbine Engine ◽  
Area Ratio ◽  
Fuel Injector ◽  
Acoustic Response ◽  
Turbine Engine ◽  
Discharge Area

This paper describes an analytical and experimental investigation to obtain the thermoacoustic response of a demonstrator gas turbine engine combustor. The combustor acoustic response for two different fuel injector design configurations was measured. It was found that the combustor maximum peak to peak pressure fluctuations were 0.6 psi to 2 psi for configuration A and B respectively. Based on the measured acoustic response, another experimental investigation was conducted to identify the design features in configuration B that caused the increase in the acoustic response. The data showed that by changing the fuel injector swirler’s vane to inner passage discharge area ratio, the engine acoustic response could be lowered to an acceptable level. A simplified analytical model based on the lumped-parameter approach was then developed to investigate the effect of geometrical changes upon the engine response. The analytical model predicted the fuel injector/swirlers acoustic response as a function of the swirlers inner passage discharge area ratio and frequency. The predictions were consistent with the experimental observations, in particular, it was predicted that as the area ratio was increased, the system reactance was decreased and as a result the system changed from a damping to an amplifying system.

Lube Oil and Bearing Thermal Management System

2009 ◽  
Author(s):  
Karleine M. Justice ◽  
Jeffrey S. Dalton ◽  
Ian Halliwell ◽  
Stephen Williamson
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Thermal Management ◽  
Gas Turbine Engine ◽  
System Level ◽  
Engine Oil ◽  
Management Systems ◽  
Lubrication System ◽  
Turbine Engine ◽  
Heat Loads

Recent improvements in technology have enabled the development of models capable of capturing performance interactions in the thermal management of air vehicle systems. Such system level models are required for better understanding of integration constraints and interactions, and are becoming increasingly important because of the need for tighter coupling between the components of thermal management systems. The study described here integrates current engine modeling capabilities with an improved, more comprehensive thermal management simulation. More specifically, the current effort evaluates the heat loads associated with the lubrication system of a gas turbine engine. The underlying engine model represents a mid-size, two-spool, subsonic transport engine. The architecture of the model is adaptable to other two-spool turbine engines and missions. Mobil Avrex S Turbo 256 engine oil is used as the lubrication medium. The model consists of five bearing heat loads. Within the engine flowpath, local temperatures and the appropriate rotational speeds are the only parameters pertinent to the heat load calculations. General assumptions have been made to simplify the representation of the lubrication system. Fuel properties into the heat exchanger are assumed. A gear box attached to the high-speed shaft operates both supply pump and scavenge pump and sends compressed air to the oil reservoir. Once the oil is distributed to the bearings, the scavenge pump collects and sends it through a filter and a fuel/oil heat exchanger before it is remixed with the contents of the reservoir. A MATLAB/Simulink modeling environment provides a general approach that may be applied to the thermal management of any engine. As a result of this approach, the new model serves as a starting point for a flexible architecture that can be modified as more detailed specifications or data are made available. In this paper, results from the simple model are compared to a more comprehensive tribology-based analysis. The results demonstrate its successful application to a typical mission, based on very limited data. In general, these results will allow system designers to conduct preliminary analyses and trade studies of gas turbine engine thermal management systems.

Experimental Investigation of an Inert Gas Generator for Fire Suppressing

2001 ◽  
Author(s):  
SooYong Kim ◽  
A. Slitenko
Keyword(s):  
Experimental Investigation ◽  
Gas Turbine ◽  
Mass Flow Rate ◽  
Oxygen Content ◽  
Flow Rate ◽  
Gas Turbine Engine ◽  
Inert Gas ◽  
Gas Generator ◽  
Turbine Engine ◽  
Exit Nozzle

Present study deals with experimental and theoretical performance analysis of an inert gas generator(IGG) which can be used as an effective mean to suppress the fire. The system consists of a gas turbine engine and afterburning system with injection of water, exit nozzle to produce the inert gas. It is generally known that the degree of oxygen content in the product of combustion depends on both inlet and outlet temperature of a combustor. Less the oxygen content in the combustion product higher will be the effectiveness of fire suppression. Injection of water brings additional advantages of suffocating and cooling effects which are both indespensable factors for fire suppressing. The special test rig was manufactured and experimental investigation of IGG system has been carried out. The automatic control system ensured stable operation of gas turbine engine and afterburner, water injection, fuel control and others. During the investigation the main parameters of gas turbine engine and auxiliarly systems were measured: gas temperature and pressure at gas turbine and afterburner exit, fuel flow rate, water mass flow rate, inlet air temperature, water temperature in the cooling chamber, mass flow rate, temperature and velocity of exhaust gas-steam mixture in the exit nozzle, oxygen content in the exit jet. The experimental investigation shows that developed IGG system can work very well for indoor fires but need some modifications in application to outdoor fire suppressing.

Sign in / Sign up

Export Citation Format

Share Document