scholarly journals Discussion: “Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator” (Tahmasebi, F., 2007, ASME J. Mech. Des., 129, pp. 320–325)

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Juan A. Carretero ◽  
Meyer A. Nahon ◽  
Ron P. Podhorodeski
Keyword(s):  
High Precision ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Three Degree Of Freedom

Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator

2006 ◽  
Vol 129 (3) ◽  
pp. 320-325 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three-degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three-DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base mounted, higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of the tangent of the half-angle between one of the limbs and the base plane. Hence, there are at most 16 assembly configurations for the manipulator. In addition, it is shown that the 16 solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

The Optimum Kinematic Design of a Spherical Three-Degree-of-Freedom Parallel Manipulator

1989 ◽  
Vol 111 (2) ◽  
pp. 202-207 ◽  
Author(s):  
C. Gosselin ◽  
J. Angeles
Keyword(s):  
Numerical Method ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Design Criteria ◽  
Kinematic Design ◽  
Three Degree Of Freedom

In this paper, the design of a spherical three-degree-of-freedom parallel manipulator is considered from a kinematic viewpoint. Three different design criteria are established and used to produce designs having optimum characteristics. These criteria are (a) symmetry (b) workspace maximization, and (c) isotropy. The associated problems are formulated and their solutions, one of them requiring to resort to a numerical method, are provided. Optimum designs are thereby obtained. A discussion on singularities is also included.

Parametric Design of a Spherical Eight-Bar Linkage Based on a Spherical Parallel Manipulator

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Parametric Design ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Arbitrary Base ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a procedure that determines the dimensions of two constraining links to be added to a three degree-of-freedom spherical parallel manipulator so that it becomes a one degree-of-freedom spherical (8, 10) eight-bar linkage that guides its end-effector through five task poses. The dimensions of the spherical parallel manipulator are unconstrained, which provides the freedom to specify arbitrary base attachment points as well as the opportunity to shape the overall movement of the linkage. Inverse kinematics analysis of the spherical parallel manipulator provides a set of relative poses between all of the links, which are used to formulate the synthesis equations for spherical RR chains connecting any two of these links. The analysis of the resulting spherical eight-bar linkage verifies the movement of the system.

A new closed-form kinematics of the generalized 3-DOF spherical parallel manipulator

Robotica ◽  
1999 ◽  
Vol 17 (5) ◽  
pp. 475-485 ◽  
Author(s):  
Zhen Huang ◽  
Y. Lawrence Yao
Keyword(s):  
Closed Form ◽  
Analytical Method ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
New Method ◽  
Numerical Example ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a new method to analyze the closed-form kinematics of a generalized three-degree-of-a-freedom spherical parallel manipulator. Using this analytical method, concise and uniform solutions are achieved. Two special forms of the three-degree-of-freedom spherical parallel manipulator, i.e. right-angle type and a decoupled type, are also studied and their unique and interesting properties are investigated, followed by a numerical example.

Kinematics of a New High Precision Three Degree-of-Freedom Parallel Manipulator

2005 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base-mounted; higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of tangent of half-angle between one of the limbs and the base plane. Hence, there are at most sixteen assembly configurations for the manipulator. In addition, it is shown that the sixteen solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

Performance Analysis of Two Robots one Serial 4R and one Parallel 3T

2015 ◽  
Vol 762 ◽  
pp. 137-146
Author(s):  
Constantin Ocnărescu
Keyword(s):  
Performance Analysis ◽  
High Precision ◽  
Parallel Manipulator ◽  
Machine Building ◽  
Degree Of Freedom ◽  
Building Industry ◽  
Attractive Alternative ◽  
Kinematic Study ◽  
Structural Solution

A geometric and kinematic study between two structures of robots was performed, respectively a mechanical anthropomorphic structure, with bars and gears, with four degree of freedom, (dof), redundant (4R), which can avoid obstacles and a parallel manipulator with translation on three axes (3T). This 3T structural solution allows rapid and precise movements, which are important characteristics for machine building industry. All these features make the parallel manipulator to be an attractive alternative to the serial ones for high precision operations in a limited workspace.

Sign in / Sign up

Export Citation Format

Share Document