scholarly journals Using Pade´ Approximants and Curve-fitting to Approximate Eigenvalues and Eigenvectors for Large Design Changes

1996 ◽  
Vol 118 (1) ◽  
pp. 151-153 ◽  
Author(s):  
J. M. Vance ◽  
J. E. Bernard
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Solution Process ◽  
Mode Shapes ◽  
Eigenvalues And Eigenvectors ◽  
Computational Burden ◽  
Design Change ◽  
Design Changes ◽  
Develop Software ◽  
Unique Method

Our overall goal is to develop software that facilitates the interactive participation of the designer in the optimization process. We are focusing this research on problems which use finite element solutions as part of the objective function. One challenge to implementing interactive participation in these types of problems is the high computational burden of computing a finite element solution for each design change. The research presented here focuses on a unique method to develop fast approximations for natural frequencies and mode shapes which can be used to avoid the time-consuming re-solution process and which will facilitate interactive design for systems with even large design changes.

Analysis Behavior of a Rig Shafting Vibration Set Changes Bearing Parameters

2013 ◽  
Vol 437 ◽  
pp. 98-101 ◽  
Author(s):  
Van Thanh Ngo ◽  
Dan Mei Xie
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Degree Of Freedom ◽  
Mode Shapes ◽  
Lateral Vibration ◽  
Eigenvalues And Eigenvectors ◽  
Fem Model ◽  
Critical Speeds ◽  
Bearing Stiffness

Frequently, in the design of machines, some of parameters that directly affect the rotordynamics of the machines are not accurately known. In particular, bearing stiffness support is one such parameter. Taking a rig shafting as an example, this paper studies the lateral vibration of the rig shafting with multi-degree-of-freedom by using finite element method (FEM). The FEM model is created and the eigenvalues and eigenvectors are calculated and analyzed to find natural frequencies, critical speeds, mode shapes. Then critical speeds and mode shapes are analyzed by set bearing stiffness changes. The model permitted to identify the critical speeds and bearings that have an important influence on the vibration behavior.

Flexural Vibration of Prestressed Concrete Bridges with Corrugated Steel Webs

2017 ◽  
Vol 17 (02) ◽  
pp. 1750023 ◽  
Author(s):  
Xia-Chun Chen ◽  
Zhen-Hu Li ◽  
Francis T. K. Au ◽  
Rui-Juan Jiang
Keyword(s):  
Finite Element ◽  
Shear Deformation ◽  
Prestressed Concrete ◽  
Natural Frequencies ◽  
Sandwich Beam ◽  
Flexural Vibration ◽  
Concrete Bridges ◽  
Mode Shapes ◽  
Beam Model ◽  
Prestressed Concrete Bridges

Prestressed concrete bridges with corrugated steel webs have emerged as a new form of steel-concrete composite bridges with remarkable advantages compared with the traditional ones. However, the assumption that plane sections remain plane may no longer be valid for such bridges due to the different behavior of the constituents. The sandwich beam theory is extended to predict the flexural vibration behavior of this type of bridges considering the presence of diaphragms, external prestressing tendons and interaction between the web shear deformation and flange local bending. To this end, a [Formula: see text] beam finite element is formulated. The proposed theory and finite element model are verified both numerically and experimentally. A comparison between the analyses based on the sandwich beam model and on the classical Euler–Bernoulli and Timoshenko models reveals the following findings. First of all, the extended sandwich beam model is applicable to the flexural vibration analysis of the bridges considered. By letting [Formula: see text] denote the square root of the ratio of equivalent shear rigidity to the flange local flexural rigidity, and L the span length, the combined parameter [Formula: see text] appears to be more suitable for considering the diaphragm effect and the interaction between the shear deformation and flange local bending. The diaphragms have significant effect on the flexural natural frequencies and mode shapes only when the [Formula: see text] value of the bridge falls below a certain limit. For a bridge with an [Formula: see text] value over a certain limit, the flexural natural frequencies and mode shapes obtained from the sandwich beam model and the classical Euler–Bernoulli and Timoshenko models tend to be the same. In such cases, either of the classical beam theories may be used.

scholarly journals Dynamics Characteristics of Blast Furnace Shell

2011 ◽  
Vol 2-3 ◽  
pp. 1018-1020
Author(s):  
De Chen Zhang ◽  
Yan Ping Sun
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Blast Furnace ◽  
Modal Analysis ◽  
Natural Frequencies ◽  
Theoretical Foundation ◽  
Structural Mechanics ◽  
Mode Shapes ◽  
The Future ◽  
Element Method

Finite element method and structural mechanics method are used to study the blast furnace shell modal analysis and the natural frequencies and mode shapes have been calculated. The two methods were compared and validated , and the results provide a theoretical foundation for the anti-vibration capabilities design of blast furnace shell in the future .

scholarly journals High-Fidelity Sensitivity Analysis of Modal Properties of Mistuned Bladed Disks Regarding Material Anisotropy

2018 ◽  
Author(s):  
Adam Koscso ◽  
Guido Dhondt ◽  
E. P. Petrov
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Coordinate Systems ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Material Orientation

A new method has been developed for sensitivity calculations of modal characteristics of bladed disks made of anisotropic materials. The method allows the determination of the sensitivity of the natural frequencies and mode shapes of mistuned bladed disks with respect to anisotropy angles that define the crystal orientation of the monocrystalline blades using full-scale finite element models. An enhanced method is proposed to provide high accuracy for the sensitivity analysis of mode shapes. An approach has also been developed for transforming the modal sensitivities to coordinate systems used in industry for description of the blade anisotropy orientations. The capabilities of the developed methods are demonstrated on examples of a single blade and a mistuned realistic bladed disk finite element models. The modal sensitivity of mistuned bladed disks to anisotropic material orientation is thoroughly studied.

scholarly journals An investigation into the free vibrations of carbon nanotubes using analytical and finite element methods

2021 ◽  
Author(s):  
Ishan Ali Khan
Keyword(s):  
Carbon Nanotubes ◽  
Finite Element ◽  
Eigenvalue Problem ◽  
Natural Frequencies ◽  
Nonlinear Eigenvalue Problem ◽  
Dynamic Stiffness ◽  
Free Vibrations ◽  
Mode Shapes ◽  
Wide Range ◽  
Walled Cnts

Since their discovery, immense attention has been given to carbon nanotubes (CNTs), due to their exceptional thermal, electronic and mechanical properties and, therefore, the wide range of applications in which they are, or can be potentially, employed. Hence, it is important that all the properties of carbon nanotubes are studied extensively. This thesis studies the vibrational frequencies of double-walled and triple-walled CNTs, with and without an elastic medium surrounding them, by using Finite Element Method (FEM) and Dynamic Stiffness Matrix (DSM) formulations, considering them as Euler-Bernoulli beams coupled with van der Waals interaction forces. For FEM modelling, the linear eigenvalue problem is obtained using Galerkin weighted residual approach. The natural frequencies and mode shapes are derived from eigenvalues and eigenvectors, respectively. For DSM formulation of double-walled CNTs, a nonlinear eigenvalue problem is obtained by enforcing displacement and load end conditions to the exact solution of single equation achieved by combining the coupled governing equations. The natural frequencies are obtained using Wittrick-Williams algorithm. FEM formulation is also applied to both double and triple-walled CNTs modelled as nonlocal Euler-Bernoulli beam. The natural frequencies obtained for all the cases, are in agreement with the values provided in literature.

scholarly journals Coupled flexural - torsional vibration and stability analysis of pre-loaded beams using conventional and dynamic finite element methods

2021 ◽  
Author(s):  
Heenkenda Jayasinghe
Keyword(s):  
Finite Element ◽  
Eigenvalue Problem ◽  
Axial Force ◽  
Torsional Vibration ◽  
Natural Frequencies ◽  
Nonlinear Eigenvalue Problem ◽  
Compressive Force ◽  
Mode Shapes ◽  
Dynamic Finite Element ◽  
Starting Point

Dynamic Finite Element (DFE) and conventional finite element formulations are developed to study the flexural - torsional vibration and stability of an isotropic, homogeneous and linearly elastic pre-loaded beam subjected to an axial load and end-moment. Various classical boundary conditions are considered. Elementary Euler - Bernoulli bending and St. Venant torsion beam theories were used as a starting point to develop the governing equations and the finite element solutions. The nonlinear Eigenvalue problem resulted from the DFE method was solved using a program code written in MATLAB and the natural frequencies and mode shapes of the system were determined form the Eigenvalues and Eigenvectors, respectively. Similarly, a linear Eigenvalue problem was formulated and solved using a MATLAB code for the conventional FEM method. The conventional FEM results were validated against those available in the literature and ANSYS simulations and the DFE results were compared with the FEM results. The results confirmed that tensile forces increased the natural frequencies, which indicates beam stiffening. On the contrary, compressive forces reduced the natural frequencies, suggesting a reduction in beam stiffness. Similarly, when an end-moment was applied the stiffness of the beam and the natural frequencies diminished. More importantly, when a force and end-moment were acting in combination, the results depended on the direction and magnitude of the axial force. Nevertheless, the stiffness of the beam is more sensitive to the changes in the magnitude and direction of the axial force compared to the moment. A buckling analysis of the beam was also carried out to determine the critical buckling end-moment and axial compressive force.

Coupled Bending-Torsion Vibration of Geared Rotors

1995 ◽  
Author(s):  
J. S. Rao ◽  
J. R. Chang ◽  
T. N. Shiau
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
Mode Shapes ◽  
Mesh Stiffness ◽  
Present Program ◽  
Gear Mesh ◽  
Pressure Angle ◽  
Torsion Vibration ◽  
Gear Mesh Stiffness

Abstract A general finite element model is presented for determining the coupled bending-torsion natural frequencies and mode shapes of geared rotors. Uncoupled bending and torsion frequencies are obtained for examples available in literature and the present program is verified against these. The effect of the gear box is considered to determine the coupled frequencies. Parameters studied include the pressure angle, gear mesh stiffness, and bearing properties. The gear pressure angle is shown to have no effect on the natural frequencies of rotors supported on isotropic bearing supports. Several case studies with bending-torsion coupling are considered and the results obtained are compared with those available in literature. The results of a general rotor system with 8lodes are also presented.

Investigation of stiffness of small wind turbine blade based on vibration analysis technique

2019 ◽  
Vol 44 (1) ◽  
pp. 49-59
Author(s):  
Nilesh Chandgude ◽  
Nitin Gadhave ◽  
Ganesh Taware ◽  
Nitin Patil
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Natural Frequency ◽  
Vibration Analysis ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Element Analysis ◽  
Finite Element Software ◽  
Small Wind Turbine

In this article, three small wind turbine blades of different materials were manufactured. Finite element analysis was carried out using finite element software ANSYS 14.5 on modeled blades of National Advisory Committee for Aeronautics 4412 airfoil profile. From finite element analysis, first, two flap-wise natural frequencies and mode shapes of three different blades are obtained. Experimental vibration analysis of manufactured blades was carried out using fast Fourier transform analyzer to find the first two flap-wise natural frequencies. Finally, the results obtained from the finite element analysis and experimental test of three blades are compared. Based on vibration analysis, we found that the natural frequency of glass fiber reinforced plastic blade reinforced with aluminum sheet metal (small) strips increases compared with the remaining blades. An increase in the natural frequency indicates an increase in the stiffness of blade.

Free Vibration Analysis of PZT Glide Heads

1999 ◽  
Vol 121 (4) ◽  
pp. 984-988 ◽  
Author(s):  
Alex Y. Tsay ◽  
Jin-Hui Ouyang ◽  
C.-P. Roger Ku ◽  
I. Y. Shen ◽  
David Kuo
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Laser Doppler Vibrometer ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Bonding Length ◽  
Measured Displacement

This paper studies natural frequencies and mode shapes of a glide head with a piezoelectric transducer (PZT) through calibrated experiments and a finite element analysis. In the experiments, the PZT transducer served as an actuator exciting the glide head from 100 kHz to 1.3 MHz, and a laser Doppler vibrometer (LDV) measured displacement of the glide head at the inner or outer rail. The natural frequencies were measured through PZT impedance and frequency response functions from PZT to LDV. In the finite element analysis, the glide head was meshed by brick elements. The finite element results show that there are two types of vibration modes: slider modes and PZT modes. Only the slider modes are important to glide head applications. Moreover, natural frequencies predicted from the finite element analysis agree well with the experimental results within 5% of error. Finally, the finite element analysis identifies four critical slider dimensions whose tolerance will significantly vary the natural frequencies: PZT bonding length, wing thickness, slider thickness, and air bearing recess depth.

A Damage Identification Method Using Vibration Modal Parameters Through Finite Element Discretization

2003 ◽  
Author(s):  
Xiaoping Zhou ◽  
Abhijit Gupta
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Damage Identification ◽  
Least Squares Method ◽  
Modal Testing ◽  
Mode Shapes ◽  
Element Formulation ◽  
Element Discretization ◽  
Damage Indices ◽  
Actual Damage

Natural frequencies and mode shapes of a structure will change whenever the structure has any kind of damage. This paper introduces a technique to quantify and locate the damage when the natural frequencies and mode shapes of undamaged and damaged structure are known. Aluminum beams (with and without damage) are used for numerical simulation and experimental verification. To establish the theoretical basis of this method, finite element formulation is used. A set of undetermined equations involving damage indices and natural frequencies and mode shapes of undamaged and damaged structures are obtained. The damage indices are computed using non-negative least squares method. Impact modal testing was conducted with three aluminum beams and damage indices based on experimental data are compared with actual damage cases to establish the effectiveness of this method to identify the damage.

Sign in / Sign up

Export Citation Format

Share Document