Two-Phase Crossflow and Boiling Heat Transfer in Horizontal Tube Bundles

1996 ◽  
Vol 118 (1) ◽  
pp. 124-131 ◽  
Author(s):  
R. Dowlati ◽  
M. Kawaji ◽  
A. M. C. Chan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Void Fraction ◽  
Mass Velocity ◽  
Flow Boiling ◽  
Horizontal Tube ◽  
Two Phase ◽  
Tube Bundles

An experimental study has been conducted to determine the void fraction, frictional pressure drop, and heat transfer coefficient for vertical two-phase crossflow of refrigerant R-113 in horizontal tube bundles under saturated flow boiling conditions. The tube bundle contained 5 × 20 tubes in a square in-line array with pitch-to-diameter ratio of 1.3. R-113 mass velocity ranged from 50 to 970 kg/m2s and test pressure from 103 to 155 kPa. The void fraction data exhibited strong mass velocity effects and were significantly less than the homogeneous and in-tube flow model predictions. They were found to be well correlated in terms of the dimensionless gas velocity, jg*. The two-phase friction multiplier data could be correlated well in terms of the Lockhart–Martinelli parameter. The validity of these correlations was successfully tested by predicting the total pressure drop from independent R-113 boiling experiments. The two-phase heat transfer coefficient data were found to agree well with existing pool boiling correlations, implying that nucleate boiling was the dominant heat transfer mode in the heat flux range tested.

Microchannel Size Effects on Two-Phase Local Heat Transfer and Pressure Drop in Silicon Microchannel Heat Sinks With a Dielectric Fluid

2007 ◽  
Author(s):  
Tannaz Harirchian ◽  
Suresh V. Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Heat Sinks ◽  
Dielectric Fluid ◽  
Two Phase ◽  
Microchannel Heat Sinks ◽  
The Heat Transfer Coefficient

Two-phase heat transfer in microchannels can support very high heat fluxes for use in high-performance electronics-cooling applications. However, the effects of microchannel cross-sectional dimensions on the heat transfer coefficient and pressure drop have not been investigated extensively. In the present work, experiments are conducted to investigate the local flow boiling heat transfer in microchannel heat sinks. The effect of channel size on the heat transfer coefficient and pressure drop is studied for mass fluxes ranging from 250 to 1600 kg/m2s. The test sections consist of parallel microchannels with nominal widths of 100, 250, 400, 700, and 1000 μm, all with a depth of 400 μm, cut into 12.7 mm × 12.7 mm silicon substrates. Twenty-five microheaters embedded in the substrate allow local control of the imposed heat flux, while twenty-five temperature microsensors integrated into the back of the substrates enable local measurements of temperature. The dielectric fluid Fluorinert FC-77 is used as the working fluid. The results of this study serve to quantify the effectiveness of microchannel heat transport while simultaneously assessing the pressure drop trade-offs.

Flow Boiling Heat Transfer in a Silicon Microchannel Heat Sink Using Liquid Crystal Thermography

2008 ◽  
Author(s):  
Ayman Megahed ◽  
Ibrahim Hassan ◽  
Tariq Ahmad
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Sink ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Microchannel Heat Sink

The present study focuses on the experimental investigation of boiling heat transfer characteristics and pressure drop in a silicon microchannel heat sink. The microchannel heat sink consists of a rectangular silicon chip in which 45 rectangular microchannels were chemically etched with a depth of 295 μm, width of 254 μm, and a length of 16 mm. Un-encapsulated Thermochromic liquid Crystals (TLC) are used in the present work to enable nonintrusive and high spatial resolution temperature measurements. This measuring technique is used to provide accurate full and local surface-temperature and heat transfer coefficient measurements. Experiments are carried out for mass velocities ranging between 290 to 457 kg/m2.s and heat fluxes from 6.04 to 13.06 W/cm2 using FC-72 as the working fluid. Experimental results show that the pressure drop increases as the exit quality and the flow rate increase. High values of heat transfer coefficient can be obtained at low exit quality (xe < 0.2). However, the heat transfer coefficient decreases sharply and remains almost constant as the quality increases for an exit quality higher than 0.2.

INVESTIGATION ON VOID FRACTION FOR TWO-PHASE FLOW PRESSURE DROP OF EVAPORATIVE R-290 IN HORIZONTAL TUBE

2016 ◽  
Vol 78 (8-4) ◽  
Author(s):  
Agus Sunjarianto Pamitran ◽  
Sentot Novianto ◽  
Normah Mohd-Ghazali ◽  
Nasruddin Nasruddin ◽  
Raldi Koestoer
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Homogeneous Model ◽  
Saturation Temperature ◽  
Horizontal Tube ◽  
Phase Flow ◽  
Two Phase ◽  
Experimental Conditions

Two-phase flow boiling pressure drop experiment was conducted to observe its characteristics and to develop a new correlation of void fraction based on the separated model. Investigation is completed on the natural refrigerant R-290 (propane) in a horizontal circular tube with a 7.6 mm inner diameter under experimental conditions of 3.7 to 9.6 °C saturation temperature, 10 to 25 kW/m2 heat flux, and 185 to 445 kg/m2s mass flux. The present experimental data was used to obtain the calculated void fraction which then was compared to the predicted void fraction with 31 existing correlations. A new void fraction correlation for predicting two-phase flow boiling pressure drop, as a function of Reynolds numbers, was proposed. The measured pressure drop was compared to the predicted pressure drop with some existing pressure drop models that use the newly developed void fraction model. The homogeneous model of void fraction showed the best prediction with 2% deviation

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

Experimental Study on Flow Boiling of HFC134a in a Multi-Port Extruded Tube

2004 ◽  
Author(s):  
Ken Kuwahara ◽  
Shigeru Koyama ◽  
Kengo Kazari
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Rectangular Channel ◽  
Large Diameter ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Inlet Temperature

In the present study, the local heat transfer and pressure drop characteristics are investigated experimentally for the flow boiling of refrigerant HFC134a in a multi-port extruded tube of 1.06mm in hydraulic diameter. The test tube is 865mm in total length made of aluminum. The pressure drop is measured at an interval of 191 mm, and the local heat transfer coefficient is measured in every subsection of 75mm in effective heating length. Experimental ranges are as follows: the mass velocity of G = 100–700 kg/m2s, the inlet temperature of Tin = 5.9–11.4 °C and inlet pressure of about 0.5 MPa. The data of pressure drop are compared with a few previous correlations for small diameter tubes, and the correlations can predict the data relatively good agreement. The data of heat transfer coefficient is compared with the correlations of Yu et al. proposed for relatively large diameter tubes. It is found that there are some differences about two phase multiplier factor of convective heat transfer between the circular channel and rectangular channel.

Sign in / Sign up

Export Citation Format

Share Document