Numerical Study of Developing Flow and Heat Transfer in a Wavy Passage

1999 ◽  
Vol 121 (4) ◽  
pp. 713-719 ◽  
Author(s):  
K. Stone ◽  
S. P. Vanka
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Spatial Location ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
The Core ◽  
Flow And Heat Transfer ◽  
Developing Flow ◽  
Energy Equations

Developing flow and heat transfer in a wavy passage are studied using a numerical scheme that solves the two-dimensional unsteady flow and energy equations. Calculations are presented for a wavy channel consisting of 14 waves. Time-dependent simulations have been performed for several Reynolds numbers. At low Reynolds numbers, the flow is steady in the complete channel. As the Reynolds number is progressively increased, the flow becomes unsteady. As a result of the unsteadiness, there is increased mixing between the core and the wall fluids, thereby increasing the heat transfer rate. With further increase in Reynolds number, the flow becomes unsteady at a much earlier spatial location.

A Numerical Study of Heat Transfer and Flow Structure in Channels With Miniature V Rib-Dimple Hybrid Structure on One Wall

2018 ◽  
Author(s):  
Peng Zhang ◽  
Yu Rao ◽  
Yanlin Li
Keyword(s):  
Heat Transfer ◽  
Turbulent Flow ◽  
Numerical Simulations ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Hybrid Structure ◽  
Transfer Enhancement ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Flow Mixing

This paper presents a numerical study on turbulent flow and heat transfer in the channels with a novel hybrid cooling structure with miniature V-shaped ribs and dimples on one wall. The heat transfer characteristics, pressure loss and turbulent flow structures in the channels with the rib-dimples with three different rib heights of 0.6 mm, 1.0 mm and 1.5 mm are obtained for the Reynolds numbers ranging from 18,700 to 60,000 by numerical simulations, which are also compared with counterpart of a pure dimpled and pure V ribbed channel. The results show that the overall Nusselt numbers of the V rib-dimple channel with the rib height of 1.5 mm is up to 70% higher than that of the channels with pure dimples. The numerical simulations show that the arrangement of the miniature V rib upstream each dimple induces complex secondary flow near the wall and generates downwashing vortices, which intensifies the flow mixing and turbulent kinetic energy in the dimple, resulting in significant improvement in heat transfer enhancement and uniformness.

scholarly journals Numerical study of gas dynamics and heat transfer in matrix channels at various rib angles

2021 ◽  
Vol 2057 (1) ◽  
pp. 012026
Author(s):  
A V Barsukov ◽  
V V Terekhov ◽  
V I Terekhov
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Gas Dynamics ◽  
Average Velocity ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Separation Flow ◽  
Maximum Heat ◽  
Maximum Heat Transfer

Abstract The results of numerical simulation of the separation flow in matrix channels by the RANS method are presented. The simulation is performed at the Reynolds number Re = 12600, determined by the mass-average velocity and the height of the channel. The distribution of the local Nusselt number is obtained for various Reynolds numbers in the range of 5÷15⋅103 and several rib angles. It is shown that the temperature distribution on the surface is highly nonuniform; in particular, the maximum heat transfer value is observed near the upper edge facets, in the vicinity of which the greatest velocity gradient is observed.

Numerical Investigation on Turbulence Statistics and Heat Transfer of a Circular Jet Impinging on a Roughened Flat Plate

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Abdulrahman Alenezi ◽  
Abdulrahman Almutairi ◽  
Hamad Alhajeri ◽  
Abdulaziz Gamil ◽  
Faisal Alshammari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Roughness Element ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Target Plate ◽  
Cross Sectional ◽  
Flow Physics ◽  
Baseline Case

Abstract A detailed heat transfer numerical study of a three-dimensional impinging jet on a roughened isothermal surface is presented and is investigated from flow physics vantage point under the influence of different parameters. The effects of the Reynolds number, roughness location, and roughness dimension on the flow physics and heat transfer parameters are studied. Additionally, the relations between average heat transfer coefficient (AHTC) and flow physics including pressure, wall shear and flow vortices with thermodynamic nonequilibrium are offered. This paper studies the effect of varying both location and dimension of the roughness element which took the shape of square cross-sectional continuous ribs to deliver a favorable trade-off between total pressure loss and heat transfer rate. The roughness element was tested for three different radial locations (R/D) = 1, 1.5, and 2 and at each location its height (i.e., width) (e) was changed from 0.25 to 1 mm in incremental steps of 0.25. The study used a jet angle (α) of 90 deg, jet-to-target distance (H/D = 6), and Re ranges from 10,000 to 50,000, where H is the vertical distance between the target plate and jet exit. The results show that the AHTC can be significantly affected by changing the geometry and dimensions of the roughness element. This variation can be either an augmentation of, or decrease in, the (HTC) when compared with the baseline case. An enhancement of 12.9% in the AHTC was achieved by using optimal location and dimensions of the roughness element at specific Reynolds number. However, a diminution between 10% and 30% in (AHTC) was attained by the use of rib height e = 1 mm at Re = 50k. The variation of both rib location and height showed better contribution in increasing heat transfer for low-range Reynolds numbers.

LES Investigation of Flow and Heat Transfer in a Channel With Dimples and Protrusions

2007 ◽  
Author(s):  
Mohammad A. Elyyan ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Reynolds Numbers ◽  
The Other ◽  
Secondary Effect ◽  
Flow Acceleration ◽  
Heat Transfer Augmentation ◽  
Flow And Heat Transfer ◽  
Separated Shear Layer ◽  
Dimple Surface

LES calculations are conducted for flow in a channel with dimples and protrusions on opposite walls with both surfaces heated at three Reynolds numbers, ReH = 220, 940, and 9300 ranging from laminar, weakly turbulent to fully turbulent, respectively. Turbulence generated by the separated shear layer in the dimple and along the downstream rim of the dimple is primarily responsible for heat transfer augmentation on the dimple surface. On the other hand, augmentation on the protrusion surface is mostly driven by flow impingement and flow acceleration between protrusions, while the turbulence generated in the wake has a secondary effect. Heat transfer augmentation ratios of 0.99 at ReH = 220, 2.9 at ReH = 940, and 2.5 at ReH = 9300 are obtained. Both skin friction and form losses contribute to pressure drop in the channel, with form losses increasing from 45% to 80% with an increase in the Reynolds number. Friction coefficient augmentation ratios of 1.67, 4.82 and 6.37 are obtained at ReH = 220, 940, and 9300, respectively. Based on the geometry studied, it is found that dimples and protrusions may not be viable heat transfer augmentation surfaces when the flow is steady and laminar.

Periodic Fluid Flow and Heat Transfer in a Square Cavity Due to an Insulated or Isothermal Rotating Cylinder

2009 ◽  
Vol 131 (11) ◽  
Author(s):  
Y.-C. Shih ◽  
J. M. Khodadadi ◽  
K.-H. Weng ◽  
A. Ahmed
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convection Heat Transfer ◽  
Reynolds Numbers ◽  
Rotating Cylinder ◽  
Flow Fields ◽  
Square Cavity ◽  
Nusselt Numbers ◽  
Flow And Heat Transfer ◽  
Rotating Objects

The periodic state of laminar flow and heat transfer due to an insulated or isothermal rotating cylinder object in a square cavity is investigated computationally. A finite-volume-based computational methodology utilizing primitive variables is used. Various rotating objects (circle, square, and equilateral triangle) with different sizes are placed in the middle of a square cavity. A combination of a fixed computational grid and a sliding mesh was utilized for the square and triangle shapes. For the insulated and isothermal objects, the cavity is maintained as differentially heated and isothermal enclosures, respectively. Natural convection heat transfer is neglected. For a given shape of the object and a constant angular velocity, a range of rotating Reynolds numbers are covered for a Pr=5 fluid. The Reynolds numbers were selected so that the flow fields are not generally affected by the Taylor instabilities (Ta<1750). The periodic flow field, the interaction of the rotating objects with the recirculating vortices at the four corners, and the periodic channeling effect of the traversing vertices are clearly elucidated. The simulations of the dynamic flow fields were confirmed against experimental data obtained by particle image velocimetry. The corresponding thermal fields in relation to the evolving flow patterns and the skewness of the temperature contours in comparison to the conduction-only case were discussed. The skewness is observed to become more marked as the Reynolds number is lowered. Transient variations of the average Nusselt numbers of the respective systems show that for high Re numbers, a quasiperiodic behavior due to the onset of the Taylor instabilities is dominant, whereas for low Re numbers, periodicity of the system is clearly observed. Time-integrated average Nusselt numbers of the insulated and isothermal object systems were correlated with the rotational Reynolds number and shape of the object. For high Re numbers, the performance of the system is independent of the shape of the object. On the other hand, with lowering of the hydraulic diameter (i.e., bigger objects), the triangle and the circle exhibit the highest and lowest heat transfers, respectively. High intensity of the periodic channeling and not its frequency is identified as the cause of the observed enhancement.

A Numerical Study of the Flow and Heat Transfer in the Pin Fin-Dimple Channels With Various Dimple Depths

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Yu Rao ◽  
Yamin Xu ◽  
Chaoyi Wan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Convective Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Transfer Performance ◽  
Number Range ◽  
Flow Friction ◽  
Pin Fin ◽  
Flow And Heat Transfer

A numerical study was conducted to investigate the effects of dimple depth on the flow and heat transfer characteristics in a pin fin-dimple channel, where dimples are located spanwisely between the pin fins. The study aimed at promoting the understanding of the underlying convective heat transfer mechanisms in the pin fin-dimple channels and improving the cooling design for the gas turbine components. The flow structure, friction factor, and heat transfer performance of the pin fin-dimple channels with various dimple depths have been obtained and compared with each other for the Reynolds number range of 8200–80,800. The study showed that, compared to the pin fin channel, the pin fin-dimple channels have further improved convective heat transfer performance, and the pin fin-dimple channel with deeper dimples shows relatively higher Nusselt number values. The study still showed a dimple depth-dependent flow friction performance for the pin fin-dimple channels compared to the pin fin channel, and the pin fin-dimple channel with shallower dimples shows relatively lower friction factors over the studied Reynolds number range. Furthermore, the computations showed the detailed characteristics in the distribution of the velocity and turbulence level in the flow, which revealed the underlying mechanisms for the heat transfer enhancement and flow friction reduction phenomenon in the pin fin-dimple channels.

Sign in / Sign up

Export Citation Format

Share Document