Measurements in a Transitional Boundary Layer With Go¨rtler Vortices

1997 ◽  
Vol 119 (3) ◽  
pp. 562-568 ◽  
Author(s):  
R. J. Volino ◽  
T. W. Simon
Keyword(s):  
Boundary Layer ◽  
Outer Part ◽  
Streamwise Velocity ◽  
Velocity Profiles ◽  
Intermittent Flow ◽  
Wall Region ◽  
Mean Velocity ◽  
Transition Mechanism ◽  
Concave Wall ◽  
The Mean

The laminar-turbulent transition process has been documented in a concave-wall boundary layer subject to low (0.6 percent) free-stream turbulence intensity. Transition began at a Reynolds number, Rex (based on distance from the leading edge of the test wall), of 3.5 × 105 and was completed by 4.7 × 105. The transition was strongly influenced by the presence of stationary, streamwise, Go¨rtler vortices. Transition under similar conditions has been documented in previous studies, but because concave-wall transition tends to be rapid, measurements within the transition zone were sparse. In this study, emphasis is on measurements within the zone of intermittent flow. Twenty-five profiles of mean streamwise velocity, fluctuating streamwise velocity, and intermittency have been acquired at five values of Rex, and five spanwise locations relative to a Go¨rtler vortex. The mean velocity profiles acquired near the vortex downwash sites exhibit inflection points and local minima. These minima, located in the outer part of the boundary layer, provide evidence of a “tilting” of the vortices in the spanwise direction. Profiles of fluctuating velocity and intermittency exhibit peaks near the locations of the minima in the mean velocity profiles. These peaks indicate that turbulence is generated in regions of high shear, which are relatively far from the wall. The transition mechanism in this flow is different from that on flat walls, where turbulence is produced in the near-wall region. The peak intermittency values in the profiles increase with Rex, but do not follow the “universal” distribution observed in most flat-wall, transitional boundary layers. The results have applications whenever strong concave curvature may result in the formation of Go¨rtler vortices in otherwise 2-D flows.

Measurements in a Transitional Boundary Layer With Görtler Vortices

1996 ◽  
Author(s):  
Ralph J. Volino ◽  
Terrence W. Simon
Keyword(s):  
Boundary Layer ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Streamwise Velocity ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
Görtler Vortices ◽  
Concave Wall ◽  
The Mean ◽  
Gortler Vortices

The laminar-turbulent transition process has been documented in a concave-wall boundary layer subject to low (0.6%) free-stream turbulence intensity. Transition began at a Reynolds number, Rex (based on distance from the leading edge of the test wall), of 3.5×105 and was completed by 4.7×105. The transition was strongly influenced by the presence of stationary, streamwise, Görtler vortices. Transition under similar conditions has been documented in previous studies, but because concave-wall transition tends to be rapid, measurements within the transition zone were sparse. In this study, emphasis is on measurements within the zone of intermittent flow. Twenty-five profiles of mean streamwise velocity, fluctuating streamwise velocity, and intermittency have been acquired at five values of Rex, and five spanwise locations relative to a Görtler vortex. The mean velocity profiles acquired near the vortex downwash sites exhibit inflection points and local minima. These minima, located in the outer part of the boundary layer, provide evidence of a “tilting” of the vortices in the spanwise direction. Profiles of fluctuating velocity and intermittency exhibit peaks near the locations of the minima in the mean velocity profiles. These peaks indicate that turbulence is generated in regions of high shear, which are relatively far from the wall. The transition mechanism in this flow is different from that on flat walls, where turbulence is produced in the near-wall region. The peak intermittency values in the profiles increase with Rex, but do not follow the “universal” distribution observed in most flat-wall, transitional boundary layers. The results have applications whenever strong concave curvature may result in the formation of Görtler vortices in otherwise 2-D flows. Because these cases were run with a low value of free-stream turbulence intensity, the flow is not a replication of a gas turbine flow. However, the results do provide a base case for further work on transition on the pressure side of gas turbine airfoils, where concave curvature effects are combined with the effects of high free-stream turbulence and strong streamwise pressure gradients, for they show the effects of embedded streamwise vorticity in a flow that is free of high-turbulence effects.

scholarly journals Active control of multiscale features in wall-bounded turbulence

2019 ◽  
Vol 36 (1) ◽  
pp. 12-21 ◽  
Author(s):  
Xiaotong Cui ◽  
Nan Jiang ◽  
Xiaobo Zheng ◽  
Zhanqi Tang
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Streamwise Velocity ◽  
Discrete Wavelet ◽  
Wall Region ◽  
Mean Velocity ◽  
Pzt Actuator ◽  
The Impact ◽  
Near Wall

Abstract This study experimentally investigates the impact of a single piezoelectric (PZT) actuator on a turbulent boundary layer from a statistical viewpoint. The working conditions of the actuator include a range of frequencies and amplitudes. The streamwise velocity signals in the turbulent boundary layer flow are measured downstream of the actuator using a hot-wire anemometer. The mean velocity profiles and other basic parameters are reported. Spectra results obtained by discrete wavelet decomposition indicate that the PZT vibration primarily influences the near-wall region. The turbulent intensities at different scales suggest that the actuator redistributes the near-wall turbulent energy. The skewness and flatness distributions show that the actuator effectively alters the sweep events and reduces intermittency at smaller scales. Moreover, under the impact of the PZT actuator, the symmetry of vibration scales’ velocity signals is promoted and the structural composition appears in an orderly manner. Probability distribution function results indicate that perturbation causes the fluctuations in vibration scales and smaller scales with high intensity and low intermittency. Based on the flatness factor, the bursting process is also detected. The vibrations reduce the relative intensities of the burst events, indicating that the streamwise vortices in the buffer layer experience direct interference due to the PZT control.

Investigation of Boundary Layer Flows Over a Flat Plate With Different-Size Transverse Square Grooves at s/w = 10

2007 ◽  
Author(s):  
Redha Wahidi ◽  
Walid Chakroun ◽  
Sami Al-Fahad
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Skin Friction ◽  
Turbulence Intensity ◽  
Viscous Sublayer ◽  
Velocity Profiles ◽  
Boundary Layer Flows ◽  
Mean Velocity ◽  
Uncertainty Range ◽  
The Mean

Turbulent boundary layer flows over a flat plate with multiple transverse square grooves spaced 10 element widths apart were investigated. Mean velocity profiles, turbulence intensity profiles, and the distributions of the skin-friction coefficients (Cf) and the integral parameters are presented for two grooved walls. The two transverse square groove sizes investigated are 5mm and 2.5mm. Laser-Doppler Anemometer (LDA) was used for the mean velocity and turbulence intensity measurements. The skin-friction coefficient was determined from the gradient of the mean velocity profiles in the viscous sublayer. Distribution of Cf in the first grooved-wall case (5mm) shows that Cf overshoots downstream of the groove and then oscillates within the uncertainty range and never shows the expected undershoot in Cf. The same overshoot is seen in the second grooved-wall case (2.5mm), however, Cf continues to oscillate above the uncertainty range and never returns to the smooth-wall value. The mean velocity profiles clearly represent the behavior of Cf where a downward shift is seen in the Cf overshoot region and no upward shift is seen in these profiles. The results show that the smaller grooves exhibit larger effects on Cf, however, the boundary layer responses to these effects in a slower rate than to those of the larger grooves.

A three-dimensional turbulent boundary layer

1965 ◽  
Vol 22 (2) ◽  
pp. 285-304 ◽  
Author(s):  
A. E. Perry ◽  
P. N. Joubert
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Three Dimensional ◽  
Outer Part ◽  
Outer Region ◽  
Experimental Results ◽  
Mean Velocity ◽  
Polar Plot ◽  
Law Of The Wall ◽  
The Mean

The purpose of this paper is to provide some possible explantions for certain observed phenomena associated with the mean-velocity profile of a turbulent boundary layer which undergoes a rapid yawing. For the cases considered the yawing is caused by an obstruction attached to the wall upon which the boundary layer is developing. Only incompressible flow is considered.§1 of the paper is concerned with the outer region of the boundary layer and deals with a phenomenon observed by Johnston (1960) who described it with his triangular model for the polar plot of the velocity distribution. This was also observed by Hornung & Joubert (1963). It is shown here by a first-approximation analysis that such a behaviour is mainly a consequence of the geometry of the apparatus used. The analysis also indicates that, for these geometries, the outer part of the boundary-layer profile can be described by a single vector-similarity defect law rather than the vector ‘wall-wake’ model proposed by Coles (1956). The former model agrees well with the experimental results of Hornung & Joubert.In §2, the flow close to the wall is considered. Treating this region as an equilibrium layer and using similarity arguments, a three-dimensional version of the ‘law of the wall’ is derived. This relates the mean-velocity-vector distribution with the pressure-gradient vector and wall-shear-stress vector and explains how the profile skews near the wall. The theory is compared with Hornung & Joubert's experimental results. However at this stage the results are inconclusive because of the lack of a sufficient number of measured quantities.

Experimental Investigation of Turbulent Boundary Layers Under Favorable Pressure Gradient

2010 ◽  
Author(s):  
Pranav Joshi ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Velocity Profiles ◽  
Skin Friction Coefficient ◽  
Mean Velocity ◽  
Freestream Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

The goal of this research is to study the effect of favorable pressure gradient (FPG) on the near wall structures of a turbulent boundary layer on a smooth wall. 2D-PIV measurements have been performed in a sink flow, initially at a coarse resolution, to characterize the development of the mean flow and (under resolved) Reynolds stresses. Lack of self-similarity of mean velocity profiles shows that the boundary layer does not attain the sink flow equilibrium. In the initial phase of acceleration, the acceleration parameter, K = v/U2dU/dx, increases from zero to 0.575×10−6, skin friction coefficient decreases and mean velocity profiles show a log region, but lack universality. Further downstream, K remains constant, skin friction coefficient increases and the mean velocity profiles show a second log region away from the wall. In the initial part of the FPG region, all the Reynolds stress components decrease over the entire boundary layer. In the latter phase, they continue to decrease in the middle of the boundary layer, and increase significantly close to the wall (below y∼0.15δ), where they collapse when normalized with the local freestream velocity. Turbulence production and wallnormal transport, scaled with outer units, show self-similar profiles close to the wall in the constant K region. Spanwise-streamwise plane data shows evidence of low speed streaks in the log layer, with widths scaling with the boundary layer thickness.

Scaling of Favorable Pressure Gradient Turbulent Boundary Layers With Eventual Relaminarization

2005 ◽  
Author(s):  
Rau´l Bayoa´n Cal ◽  
Xia Wang ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

Applying similarity analysis to the RANS equations of motion for a pressure gradient turbulent boundary layer, Castillo and George [1] obtained the scalings for the mean deficit velocity and the Reynolds stresses. Following this analysis, Castillo and George studied favorable pressure gradient (FPG) turbulent boundary layers. They were able to obtain a single curve for FPG flows when scaling the mean deficit velocity profiles. In this study, FPG turbulent boundary layers are analyzed as well as relaminarized boundary layers subjected to an even stronger FPG. It is found that the mean deficit velocity profiles diminish when scaled using the Castillo and George [1] scaling, U∞, and the Zagarola and Smits [2] scaling, U∞δ*/δ. In addition, Reynolds stress data has been analyzed and it is found that the relaminarized boundary layer data decreases drastically in all components of the Reynolds stresses. Furthermore, it will be shown that the shape of the profile for the wall-normal and Reynolds shear stress components change drastically given the relaminarized state. Therefore, the mean velocity deficit profiles as well as Reynolds stresses are found to be necessary in order to understand not only FPG flows, but also relaminarized boundary layers.

Heat Transfer in the Forced Laminar Wall Jet

1997 ◽  
Vol 119 (3) ◽  
pp. 451-459 ◽  
Author(s):  
D. L. Quintana ◽  
M. Amitay ◽  
A. Ortega ◽  
I. J. Wygnanski
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Skin Friction ◽  
Streamwise Velocity ◽  
Wall Heat Flux ◽  
Wall Jet ◽  
Wall Region ◽  
Mean Velocity ◽  
Constant Wall Temperature ◽  
The Mean

The mean and fluctuating characteristics of a plane, unsteady, laminar, wall jet were investigated experimentally for a constant wall-temperature boundary condition. Temperature and streamwise velocity profiles, including the downstream development of the thermal and hydrodynamic boundary layer thicknesses, were obtained through simultaneous hot and cold wire measurements in air. Even at relatively low temperature differences, heating or cooling of a floor surface sufficiently altered the mean velocity profile in the inner, near-wall region to produce significant effects on the jet stability. Selective forcing of the flow at the most amplified frequencies produced profound effects on the temperature and velocity fields and hence the time-averaged heat transfer and shear stress. Large amplitude excitation of the flow (up to 2 percent of the velocity measured at the jet exit plane) at a high frequency resulted in a reduction in the maximum skin friction by as much as 65 percent, with an increase in the maximum wall heat flux as high as 45 percent. The skin friction and wall heat flux were much less susceptible to low-frequency excitation.

scholarly journals Turbulent boundary layers and channels at moderate Reynolds numbers

2010 ◽  
Vol 657 ◽  
pp. 335-360 ◽  
Author(s):  
JAVIER JIMÉNEZ ◽  
SERGIO HOYAS ◽  
MARK P. SIMENS ◽  
YOSHINORI MIZUNO
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Turbulent Flows ◽  
Pressure Fluctuations ◽  
Reynolds Numbers ◽  
Streamwise Velocity ◽  
Rotational Flow ◽  
Mean Velocity ◽  
The Mean ◽  
External Flows

The behaviour of the velocity and pressure fluctuations in the outer layers of wall-bounded turbulent flows is analysed by comparing a new simulation of the zero-pressure-gradient boundary layer with older simulations of channels. The 99 % boundary-layer thickness is used as a reasonable analogue of the channel half-width, but the two flows are found to be too different for the analogy to be complete. In agreement with previous results, it is found that the fluctuations of the transverse velocities and of the pressure are stronger in the boundary layer, and this is traced to the pressure fluctuations induced in the outer intermittent layer by the differences between the potential and rotational flow regions. The same effect is also shown to be responsible for the stronger wake component of the mean velocity profile in external flows, whose increased energy production is the ultimate reason for the stronger fluctuations. Contrary to some previous results by our group, and by others, the streamwise velocity fluctuations are also found to be higher in boundary layers, although the effect is weaker. Within the limitations of the non-parallel nature of the boundary layer, the wall-parallel scales of all the fluctuations are similar in both the flows, suggesting that the scale-selection mechanism resides just below the intermittent region, y/δ = 0.3–0.5. This is also the location of the largest differences in the intensities, although the limited Reynolds number of the boundary-layer simulation (Reθ ≈ 2000) prevents firm conclusions on the scaling of this location. The statistics of the new boundary layer are available from http://torroja.dmt.upm.es/ftp/blayers/.

On the Tendency to Self-Preservation in Axisymmetric Ducted Jets

1964 ◽  
Vol 86 (4) ◽  
pp. 765-771 ◽  
Author(s):  
R. Curtet ◽  
F. P. Ricou
Keyword(s):  
Boundary Layer ◽  
Equations Of Motion ◽  
Form Factors ◽  
Velocity Profiles ◽  
Stream Velocity ◽  
Mean Velocity ◽  
Velocity Fluctuations ◽  
Air Jet ◽  
The Mean ◽  
Secondary Stream

If it is assumed that the mean-velocity profiles of a ducted jet are similar in form sufficiently for downstream of the orifice it is possible, as shown in earlier papers [1, 2, 3], to integrate the equations of motion using the boundary-layer approximation and assuming a constant-energy secondary stream. It is necessary to know when and how this limiting profile is reached, and whether a similar tendency to self-preservation of the components of the velocity fluctuations is observed before the jet reaches the duct-wall boundary layer. Measurements have been made in an axisymmetric ducted air jet of the mean and fluctuating velocities, jet width, secondary-stream velocity, ductwall static pressure, and the boundary layer thickness. Results are compared with values predicted by the approximate jet theory. The authors define form factors calculated from measured profiles of mean velocities, of radial and longitudinal components of the velocity fluctuations, and of the shear stress. The variation of these form factors indicates a definite tendency to similarity for the mean velocity profiles; however, departures from similarity persist for the velocity fluctuations to the limit of measurements, about three duct diameters (40 nozzle diameters).

scholarly journals Turbulence structures and statistics of a supersonic turbulent boundary layer subjected to concave surface curvature

2019 ◽  
Vol 865 ◽  
pp. 60-99 ◽  
Author(s):  
Mingbo Sun ◽  
Neil D. Sandham ◽  
Zhiwei Hu
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Turbulent Flows ◽  
Large Scale ◽  
Layer Structure ◽  
Outer Part ◽  
Streamwise Velocity ◽  
Budget Analysis ◽  
Concave Wall

Supersonic turbulent flows at Mach 2.7 over concave surfaces for two different radii of curvature were investigated and compared with a flat plate turbulent boundary layer using direct numerical simulations. The streamwise velocity reduces in the outer part of the boundary layer due to compression, while it increases near the wall due to curvature, with a higher shape factor for the concave cases. The near-wall spanwise streak spacing reduces compared to the flat plate, with large-scale streaks and turbulence amplification also observed. Streamwise velocity iso-surfaces and streamlines show the generation of Görtler-like vortices, consistent with significant centrifugal effects. Abundant small vortices are shown to be associated with large baroclinic production of vorticity that is caused by the density and pressure gradients that are associated with concave compression. Profiles of turbulent kinetic energy and turbulent Mach number exhibit a characteristic two-layer structure in the concave boundary layer cases. In the outer layer, turbulence is greatly amplified, whereas a local balance exists in the inner layer. Turbulent energy budget analysis shows that both production and dissipation increase near the concave wall, whereas in the outer part of the boundary layer, the production is increased and ultimately balanced by convection and turbulent transport.

Sign in / Sign up

Export Citation Format

Share Document